When max client was set to 512 in qca99x0, there was host memory
alloc failure during wmi service ready event handling. This issue
got resolved now, increasing max client limit from 256 to 512.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Host memory required for firmware is allocated while handling
wmi service ready event. Right now, wmi service ready is handled
in tasklet context and it calls dma_alloc_coherent() with atomic
flag (GFP_ATOMIC) to allocate memory in host needed for firmware.
The problem is, dma_alloc_coherent() with GFP_ATOMIC fails in
the platform (at least in AP platform) where it has less atomic
pool memory (< 2mb). QCA99X0 requires around 2 MB of host memory
for one card, having additional QCA99X0 card in the same platform
will require similarly amount of memory. So, it's not guaranteed that
all the platform will have enough atomic memory pool.

Fix this issue, by handling wmi service ready event in workqueue
context and calling dma_alloc_coherent() with GFP_KERNEL. mac80211 work
queue will not be ready at the time of handling wmi service ready.
So, it can't be used to handle wmi service ready. Also, register work
gets scheduled during insmod in existing ath10k_wq and waits for
wmi service ready to completed. Both workqueue can't be used for
this purpose. New auxiliary workqueue is added to handle wmi service
ready.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.

 cryptmode:

   0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
      encapsulation to the firmware. This is the default mode.
   1: Use sofware crypto engine globally with raw mode TX/RX
      encapsulation to the firmware.

Known limitation:
   A-MSDU must be disabled for RAW Tx encap mode to perform well when
   heavy traffic is applied.

Testing: (by Michal Kazior <michal.kazior@tieto.com>)

     a) Performance Testing

      cryptmode=1
       ap=qca988x sta=killer1525
        killer1525  ->  qca988x     194.496 mbps [tcp1 ip4]
        killer1525  ->  qca988x     238.309 mbps [tcp5 ip4]
        killer1525  ->  qca988x     266.958 mbps [udp1 ip4]
        killer1525  ->  qca988x     477.468 mbps [udp5 ip4]
        qca988x     ->  killer1525  301.378 mbps [tcp1 ip4]
        qca988x     ->  killer1525  297.949 mbps [tcp5 ip4]
        qca988x     ->  killer1525  331.351 mbps [udp1 ip4]
        qca988x     ->  killer1525  371.528 mbps [udp5 ip4]
       ap=killer1525 sta=qca988x
        qca988x     ->  killer1525  331.447 mbps [tcp1 ip4]
        qca988x     ->  killer1525  328.783 mbps [tcp5 ip4]
        qca988x     ->  killer1525  375.309 mbps [udp1 ip4]
        qca988x     ->  killer1525  403.379 mbps [udp5 ip4]
        killer1525  ->  qca988x     203.689 mbps [tcp1 ip4]
        killer1525  ->  qca988x     222.339 mbps [tcp5 ip4]
        killer1525  ->  qca988x     264.199 mbps [udp1 ip4]
        killer1525  ->  qca988x     479.371 mbps [udp5 ip4]

      Note:
       - only open network tested for RAW vs nwifi performance comparison
       - killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
       - used iperf
       - OTA, devices a few cm apart from each other, no shielding
       - tcpX/udpX, X - means number of threads used

      Overview:
       - relative Tx performance drop is seen but is within reasonable and
         expected threshold (A-MSDU must be disabled with RAW Tx)

     b) Connectivity Testing

      cryptmode=1
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan  OK

      Note:
       - each test takes all possible endpoint pairs and pings
       - each pair-ping flushes arp table
       - ip6 is used

     c) Testbed Topology:

      1ap1sta:
        [ap] ---- [sta]

        endpoints: ap, sta

      1ap1sta2br:
        [veth0] [ap] ---- [sta] [veth2]
           |     |          |     |
        [veth1]  |          \   [veth3]
            \   /            \  /
            [br0]            [br1]

        endpoints: veth0, veth2, br0, br1
        note: STA works in 4addr mode, AP has wds_sta=1

      1ap1sta2br1vlan:
        [veth0] [ap] ---- [sta] [veth2]
           |     |          |     |
        [veth1]  |          \   [veth3]
            \   /            \  /
          [br0]              [br1]
            |                  |
          [vlan0_id2]        [vlan1_id2]

        endpoints: vlan0_id2, vlan1_id2
        note: STA works in 4addr mode, AP has wds_sta=1

Credits:

    Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
    amsdu issue, contributed a workaround (already squashed into this
    patch), and contributed the throughput and connectivity tests results.
Signed-off-by: NDavid Liu <cfliu.tw@gmail.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Tested-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During tx completion, tx_lock is held for longer than required, preventing
efficient refill of htt->pending_tx. Refactor the code so that only MSDU
related operations are protected by the lock.

Improves downstream performance on a dual-core ARM Freescale LS1024A
(f.k.a. Mindspeed Comcerto 2000) AP with a 3x3 client from 495 to 580 Mbps.
Other CPU bound multicore systems may also benefit.
Signed-off-by: NDenton Gentry <dgentry@google.com>
Signed-off-by: NAvery Pennarun <apenwarr@google.com>
[mfaltesek@google.com: removed conflicting code for tracking msdu_ids.]
Signed-off-by: NMarty Faltesek <mfaltesek@google.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When using DFS channels on Ath10k, kernel log has repeated warning message
'failed to process fft: -22' typically under medium/heavy traffic.

This patch switches the warnings to driver debug (WMI events) mode only
thus reducing log file noise.

DFS and spectral scan share underlying HW mechanisms and enabling one
(DFS) enables the other (spectral scan) as far as event reporting from
firmware to driver is concerned. Spectral scan events take no part in
processing of DFS radar pulses which are delivered as distinct events,
so the fft (spectral event) warning is harmless and DFS interference
detection/protection still occurs.

Symptoms seen & fix tested in both debug & non-debug modes on TP-Link
Archer C7 v2 platform.
Signed-off-by: NKevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes two misspellings of "distribution" in a comment.
Signed-off-by: NNik Nyby <nikolas@gnu.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HTT_H2T_MSG_TYPE_MGMT_TX msg in 10.4 firmware carries additional
4 byte in htt_mgmt_tx_desc where it tells to firmware that at what
rate mgmt frame has to go out in the air. It's an optional parameter,
setting this field to zero will force firmware to choose auto rate
and send the frame out.

Those 4 byte info is missed out in the current code and 10.4 firmware
ended up reading some junk in those 4 byte and sometime malfunctioning.

Fix it by adding 4 byte in struct htt_mgmt_tx_desc. Non 10.4 firmware
will not process those four byte. So, adding 4 byte at the end of
struct htt_mgmt_tx_desc will not create any impact on other chipset.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The patch adds support to offload TCP/UDP checksum
calculations for QCA99x0.
Signed-off-by: NManikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

chandef is initialized with NULL and on the very next line, we are using it to
get channel, which is not correct. Channel should be initialized after
obtaining chandef.

Found by cppcheck:

ath/ath10k/mac.c:839]: (error) Possible null pointer dereference: chandef
Signed-off-by: NManinder Singh <maninder1.s@samsung.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 chip has an extra 4 bytes in rx_msdu_start,
20 bytes in rx_msdu_end and 20 bytes in rx_ppdu_end structure
which are used in htt_rx_desc and HTT Rx ring offset setup.
This is necessary for correct Rx for QCA99X0 or Rx descriptors
will be overwritten and corrupted.

With this patch QCA988X and QCA6174 will have extra 44 bytes
padding in Rx descriptor layout which is harmless.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

rx_ppdu_end_common structure is valid for both of qca998x and
qca6174, but not for qca99x0 since it has new additional members.
Hence update the common structure to cover qca99x0 as well.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since QCA99X0 uses fragmentation descriptor differently from
other ones on tx path, we need to handle it separately.

QCA99X0 is using 48 bits for address and 16 bits for length
out of 2 dword and each values have to be programmed by frag
desc base addr + msdu id, so that hardware can retrieve
corresponding frag data.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is observed that during cold reset pcie access right
after a write operation to SOC_GLOBAL_RESET_ADDRESS causes
Data Bus Error and system hard lockup. The reason
for bus error is that pcie needs some time to get
back to stable state for any transaction during cold reset. Add
delay of 20 msecs after write of SOC_GLOBAL_RESET_ADDRESS
to fix this issue. This patch is tested on QCA988X. This is
also tested on QCA99X0 which is WIP.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Major changes in ath10k:

* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch

FCC long pulse radar (type 5) requires pulses to be
checked for chirping. This patch implements chirp
detection based on the FFT data provided for long
pulses.

A chirp is detected when a set of criteria defined
by FCC pulse characteristics is met, including
* have at least 4 FFT samples
* max_bin index moves equidistantly between samples
* the gradient is within defined range

The chirp detection has been tested with reference
radar generating devices and proved to work reliably.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The chip reports radar pulses on extension channel
even if operating in HT20 mode. This patch adds a
sanity check for HT40 mode before it feeds pulses
on extension channel to the pattern detector.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

commit 2c86c275 ("Add ipw2100 wireless driver.") introduced
HW_PHY_OFF_LOOP_DELAY (HZ / 5000) which always evaluated to 0. Clarified
by Stanislav Yakovlev <stas.yakovlev@gmail.com> that it should be 50
milliseconds thus fixed up to msecs_to_jiffies(50).
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Acked-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Concurrent AP/GO operation on different channels
isn't really supported well by the firmware so
it's better to remove it from being advertised.

Also tune the way station and p2p client interface
limits are expressed to allow station + 2x p2p
client or station + p2p client + p2p go.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Whenever any vdev was supposed to be paused all Tx
queues were stopped (except offchannel) instead of
only these associated with the given vdev.

This caused subtle issues with
multi-channel/multi-vif scenarios, e.g.
authentication of station vif could sometimes fail
depending on fw tx pause request timing.

Fixes: b4aa539d ("ath10k: implement tx pause wmi event")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Psmode can be forcefully enabled when vdev isn't
started. It isn't guaranteed that mac80211 will
re-issue psmode setting after vdev is started
unless actual bss_conf.ps value has changed.

Even if this doesn't fix any problems now it may
prevent future breakage.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since fcf98446 ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.

This fixes some P2P connection setup issues.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Further testing proved that multi-channel AP+STA
on QCA6174 with RM.2.0-00088 should have powersave
force-disabled to avoid beacon misses/skipping on
either side which in turn could disrupt
communication.

Since AP never has arvif->ps don't even bother
checking it. Other combinations may be broken as
well so disallow powersave with multivif outright
unless firmware advertises otherwise.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mac80211 already does provide complete IEs for
Probe Requests for hw scan and ath10k firmware was
appending duplicate Supported Rates IEs
unnecessarily.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In commit 418ca599 ("ath10k: Make target cpu address to
CE address conversion chip specific") mask 0x7fff is added
by mistake instead of 0x7ff. Fix this regression.

Fixes: 418ca599 ("ath10k: Make target cpu address to CE address conversion chip specific")
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

commit a521ee98 ("ath10k: Add new reg_address/mask to hw register
table") broke QCA61x4 support by providing wrong
fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028.

User experience was a failing boot up sequence (crashing device during
initialization):

[  181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[  181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[  181.688886] ath10k_pci 0000:02:00.0: device has crashed during init
[  181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70
[  181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70
[  181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70

Fix it by updating the address with correct value.

Fixes: a521ee98 ("ath10k: Add new reg_address/mask to hw register table")
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sathya Perla says:

====================
be2net: patch set

Hi David, the following patch set has code cleanup patches, minor enhancements
and non-critical fixes. Pls consider applying to the net-next tree. Thanks!

Patch 1 removes duplicate code in be_setup_wol() routine making it simpler
and more readable.

Patch 2 fixes the the bridge mode return value for the ndo_bridge_getlink()
call. Instead of just relying on the SRIOV enabled state, the driver now
queries the FW, for the actual mode of bridge.

Patch 3 removes code for setting D0 power state as it's already done
in pci_enable_device()

Patch 4 fixes a bad return value in be_check_ufi_compatibility() routine
introduced by an earlier commit.

Patch 5 fixes a field in udp header being accessed while in network endian
format.

Patch 6 fixes the be_mcc_notify() routine to return an error status when
the FW/HW is in an error state.

Patch 7 fixes the be_cmd_rx_filter() routine to issue the RX_FILTER cmd
and not wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.

Patch 8 fixes the be_cmd_set_loopback() routine to issue the LOOPBACK cmd
and not wait for the FW completion while spin_lock_bh() is held on the
mcc_lock. As the cmd is always issued from ethtool in a process context,
it can sleep till the FW completion is received.

Patch 9 bumps up the driver version to 10.6.0.3
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SET_LOOPBACK_MODE command is always issued from ethtool only in a
process context. So, while waiting for the cmd to complete, the driver
can sleep instead of holding spin_lock_bh() on the mcc_lock. This is done
by calling be_mcc_notify() instead of be_mcc_notify_wait() (that returns
only after the cmd completes while the MCCQ is locked).
Signed-off-by: NSuresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fix makes the RX_FILTER cmd asynchronous, i.e., the caller issues
this cmd and doesn't wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.
Signed-off-by: NSuresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the adapter is in error state, return error from be_mcc_notify()
so that the caller routines need not sleep waiting for a response.
Signed-off-by: NSuresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "dest" field in the UDP-hdr of a TX skb is in network endian format.
Convert it to host endian before accessing it. The os2bmc patch,
mentioned below introduced this code.

Fixes: 760c295e ("be2net: Support for OS2BMC")
Signed-off-by: NVenkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the commit a6e6ff6e
("be2net: simplify UFI compatibility checking"), a return value of "-1"
was incorrectly used in place of "false". This patch fixes it.

Fixes: a6e6ff6e ("be2net: simplify UFI compatibility checking")
Signed-off-by: NVasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_enable_device() call sets device power state to D0; there is no need
doing it again.
Signed-off-by: NKalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code assumes that bridge functionality (EVB) in the adapter
is enabled only when SR-IOV is enabled. This is not always true.
This patch uses the GET_HSW_CONFIG FW cmd to query this from the FW.
Signed-off-by: NKalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change will make be_setup_wol() routine more compact and readable
by removing some duplicate code.
Signed-off-by: NKalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If outgoing interface is specified and the candidate address is
restricted to the outgoing interface, it is enough to iterate
over that given interface only.
Signed-off-by: NYOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: NErik Kline <ek@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support manually setting the polarity to mdi or mdix
Signed-off-by: NDavid Thomson <david.thomson@alliedtelesis.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the mdix setting from ethtool down to the phy driver, to allow
driver specific implementations of manually setting the polarity.
Signed-off-by: NDavid Thomson <david.thomson@alliedtelesis.co.nz>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 900f65d3 ("tcp: move duplicate code from
tcp_v4_init_sock()/tcp_v6_init_sock()"), we no longer
need to export tcp_init_xmit_timers()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>