This will avoid unnecessary forward declaration of
any kind in the future.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This prevents protected flag being stripped from
undecrypted raw sniffed frames when monitor
interface is active.
Reported-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Tested-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The channel_switch_beacon callback is optional, so it doesn't have to
be defined if it's not going to do anything useful with it.  Both
ath9k and ath10k define the callback and just returns.  This commit
removes them.

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

tmp may be used uninitialized if ath10k_bmi_read_memory() returns
an error.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Recently there was a bug discovered that involved
hif_stop() being called twice that ended up with a
double free_irq() call but it only manifested with
multiple MSI interrupts mapping.

Catch this kind of a problem early in driver
regardless of interrupt mapping.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was possible to call hif_stop() 2 times through
ath10k_htc_connect_init() timeout failpath which
could lead to double free_irq() kernel splat for
multiple MSI interrupt case.

Re-order init sequence to avoid this problem. The
HTC stop shouldn't stop HIF implicitly since it
doesn't implicitly start it. Since the re-ordering
required some functions to be split/removed/renamed
rename a few functions to make more sense while at
it.
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Verified that target's tx/rx chain register is set appropriately,
and that the tx rate goes down as number of chains
decrease, but I did not actually try to verify antenna
ceased to transmit when disabled.

kvalo: move ar->supp_*_chainmask initialisation to ath10k_mac_register()
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NAvery Pennarun <apenwarr@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix sending and receiveing protected managment frames.
Lack of protected flag for received protected action frames
causes report these frames as unprotected robust action frames.
If the driver in AP mode sent frame with protected flag and
CCMP header using IEEE80211_KEY_FLAG_SW_MGMT_TX flag,
the FW encrypted frames once again. From user side all
received SA Query Requests and Responses were skipped and
all protected action frames were sent as malformed packets.
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

On ARM-based (MSM mach), the pci_assign_resource() is passing
some invalid pointers and leading to L2 cache errors,
what prevents the PCI communication completly.

So far I have not found this funtion to be directly called by
any other wifi driver and did not found this assigning needed
on any other platform. So removing it completely.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This can be useful for early initialization
debugging, i.e. ROM crashes.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sometimes warm reset works upon retry. It might be
related to imperfect warm reset routine, but for
now let's just do the retries.

This should improve the reliability of some chips
that hang/crash with cold reset which is used as a
last resort if warm reset fails.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Warm reset is now able to recover after device
crashes which required a cold reset before.

This should greatly reduce chances of getting data
bus errors or host system freezes due to buggy
cold reset on some chips.

kvalo: use ath10k_pci_soc_*()
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Simple typo fix.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Apparently firmware can sometimes report a
sequence with the first rx descriptor saying it's
not the last MSDU. In that case msdu_chaining
value could be overwritten saying it's not a
chained MSDU. This in turn led to skb_push panic
as the frame could be treated as an A-MSDU instead
of a chained MSDU.
Reported-By: NAvery Pennarun <apenwarr@gmail.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

msdu_payId was read before txrx tasklet was killed
so it was possible to end up using an invalid
sk_buff pointer leading to a panic.

Make sure to sanitize rx ring sk_buff pointers and
make the clean up go through all possible entries
and not rely on coherent-DMA mapped u32 index
which could be (in theory) corrupted by the device
as well.
Reported-By: NAvery Pennarun <apenwarr@gmail.com>
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJahnavi Meher <jahnavi.meher@redpinesignals.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The struct cfg80211_chan_def contains additional info to derive the
bandwidth and side-band information of the chanspec. This patch adds
chandef_to_chanspec() function used in IBSS join and starting AP
operation.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The device is queried about the usability of channels, but it did not
take 80MHz channels into consideration. This patch adds processing those
chanspecs and clear the NO_80MHZ flag for those control/primary channels.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function does not provide any additional functionality and is
used only once so just get rid of it.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By default allow 80Mhz in custom regulatory rules of the 5G band so
the channels will not be flagged with N0_80MHZ.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Although brcmfmac support several 11ac devices it did not advertise
VHT related information to cfg80211.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel values used by firmware is handled using conversion functions
depending on the type of chip. These functions were already in place but
lacked proper support for 80MHz channel definitions. This patch adds the
support for that.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the .start_ap callback cfg80211_get_chandef_type() was used to
provide debug log info. However, this causes a warning when the
chandef contains VHT channel with 80MHz bandwidth. Avoid the warning
by just printing the channel and bandwidth instead.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The DISASSOC command needs to be sent to firmware when a connection
loss is detected by firmware (e.g., beacon timeout). Otherwise the
next connect request fails due to a lingering LINK(down) event from
firmware. This patch resolves the issue by using brcmf_link_down()
handler, instead of the incomplete duplicated codes.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NDaniel Kim <dekim@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver serializes the nvram firmware file before sending it
to the device. This patch enhances this to assure serialized data
is properly formatted and provide warnings on syntax failures.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

FWS is always queuing frames and using a worker for de-queueing,
this is not always efficient for all bus layer. For example SDIO
has an internal queue and worker making the queueing of FWS
unnecessary. Make it possible to bypass the worker if fws mode
is none using a bus interface configuration. For USB bus layer
this configuration is set true to have fws provide queueing
regardless the fws mode.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tracking and handling of 802.1x frames is done in two modules, it
is more logical and clear to move this to dhd_linux module.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In tx_finalize the hdrpull is performed. For the new protocol
msgbuf this is complex, because it does not use protocol headers
in front of payload anymore and therefor can not determine interface
index in the hdr pulll operation. Move out the hdrpull operation
from tx_finalize to make msgbuf implementation easier.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently firmware roaming support is not reported to cfg80211.
This patch reports the support of firmware based roaming when
it is enabled.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NDaniel Kim <dekim@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a BSS provides both 2.4GHz and 5GHz bands, in many cases it
makes sense to choose 5GHz. Typically a 5GHz channel is less crowded
and has less interference and therefore its performance will be
better than a crowded 2.4 GHz channel. This patch configures
'join_pref' to induce firmware to preferably select 5GHz BSS.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NDaniel Kim <dekim@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

and use it. This move need changes in both drivers.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

to fix compile errors
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>