提交 93f7848b 编写于 作者: J Jeff Kirsher

myri*: Move the Myricom drivers

Move the Myricom drivers into drivers/net/ethernet/myricom/ and make
the necessary Kconfig and Makefile changes.

CC: Andrew Gallatin <gallatin@myri.com>
CC: Brice Goglin <brice@myri.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
上级 5a2cc190
......@@ -4335,7 +4335,7 @@ M: Andrew Gallatin <gallatin@myri.com>
L: netdev@vger.kernel.org
W: http://www.myri.com/scs/download-Myri10GE.html
S: Supported
F: drivers/net/myri10ge/
F: drivers/net/ethernet/myricom/myri10ge/
NATSEMI ETHERNET DRIVER (DP8381x)
M: Tim Hockin <thockin@hockin.org>
......
......@@ -1519,32 +1519,6 @@ config VXGE_DEBUG_TRACE_ALL
the vxge driver. By default only few debug trace statements are
enabled.
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
depends on PCI && INET
select FW_LOADER
select CRC32
select INET_LRO
---help---
This driver supports Myricom Myri-10G Dual Protocol interface in
Ethernet mode. If the eeprom on your board is not recent enough,
you will need a newer firmware image.
You may get this image or more information, at:
<http://www.myri.com/scs/download-Myri10GE.html>
To compile this driver as a module, choose M here. The module
will be called myri10ge.
config MYRI10GE_DCA
bool "Direct Cache Access (DCA) Support"
default y
depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
---help---
Say Y here if you want to use Direct Cache Access (DCA) in the
driver. DCA is a method for warming the CPU cache before data
is used, with the intent of lessening the impact of cache misses.
config PASEMI_MAC
tristate "PA Semi 1/10Gbit MAC"
depends on PPC_PASEMI && PCI && INET
......
......@@ -151,7 +151,6 @@ obj-$(CONFIG_R8169) += r8169.o
obj-$(CONFIG_IBMVETH) += ibmveth.o
obj-$(CONFIG_S2IO) += s2io.o
obj-$(CONFIG_VXGE) += vxge/
obj-$(CONFIG_MYRI10GE) += myri10ge/
obj-$(CONFIG_PXA168_ETH) += pxa168_eth.o
obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
obj-$(CONFIG_DM9000) += dm9000.o
......
......@@ -21,6 +21,7 @@ source "drivers/net/ethernet/emulex/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
source "drivers/net/ethernet/mellanox/Kconfig"
source "drivers/net/ethernet/myricom/Kconfig"
source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/racal/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
......
......@@ -12,6 +12,7 @@ obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
obj-$(CONFIG_SFC) += sfc/
......
#
# Myricom device configuration
#
config NET_VENDOR_MYRI
bool "Myricom devices"
depends on PCI && INET
---help---
If you have a network (Ethernet) card belonging to this class, say
Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about Myricom cards. If you say Y, you will be asked for
your specific card in the following questions.
if NET_VENDOR_MYRI
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
depends on PCI && INET
select FW_LOADER
select CRC32
select INET_LRO
---help---
This driver supports Myricom Myri-10G Dual Protocol interface in
Ethernet mode. If the eeprom on your board is not recent enough,
you will need a newer firmware image.
You may get this image or more information, at:
<http://www.myri.com/scs/download-Myri10GE.html>
To compile this driver as a module, choose M here. The module
will be called myri10ge.
config MYRI10GE_DCA
bool "Direct Cache Access (DCA) Support"
default y
depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
---help---
Say Y here if you want to use Direct Cache Access (DCA) in the
driver. DCA is a method for warming the CPU cache before data
is used, with the intent of lessening the impact of cache misses.
endif # NET_VENDOR_MYRI
#
# Makefile for the Myricom network device drivers.
#
obj-$(CONFIG_MYRI10GE) += myri10ge/
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册