mlx4: Move the Mellanox driver

Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.

CC: Roland Dreier <roland@kernel.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/Kconfig

@@ -1554,30 +1554,6 @@ config PASEMI_MAC
 	  This driver supports the on-chip 1/10Gbit Ethernet controller on
 	  PA Semi's PWRficient line of chips.
 
-config MLX4_EN
-	tristate "Mellanox Technologies 10Gbit Ethernet support"
-	depends on PCI && INET
-	select MLX4_CORE
-	select INET_LRO
-	help
-	  This driver supports Mellanox Technologies ConnectX Ethernet
-	  devices.
-
-config MLX4_CORE
-	tristate
-	depends on PCI
-	default n
-
-config MLX4_DEBUG
-	bool "Verbose debugging output" if (MLX4_CORE && EXPERT)
-	depends on MLX4_CORE
-	default y
-	---help---
-	  This option causes debugging code to be compiled into the
-	  mlx4_core driver.  The output can be turned on via the
-	  debug_level module parameter (which can also be set after
-	  the driver is loaded through sysfs).
-
 config TEHUTI
 	tristate "Tehuti Networks 10G Ethernet"
 	depends on PCI

drivers/net/Makefile

@@ -157,7 +157,6 @@ obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
 obj-$(CONFIG_DM9000) += dm9000.o
 obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o
 pasemi_mac_driver-objs := pasemi_mac.o pasemi_mac_ethtool.o
-obj-$(CONFIG_MLX4_CORE) += mlx4/
 obj-$(CONFIG_ENC28J60) += enc28j60.o
 obj-$(CONFIG_ETHOC) += ethoc.o
 obj-$(CONFIG_GRETH) += greth.o

drivers/net/ethernet/Kconfig

@@ -20,6 +20,7 @@ source "drivers/net/ethernet/chelsio/Kconfig"
 source "drivers/net/ethernet/emulex/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"
 source "drivers/net/ethernet/i825xx/Kconfig"
+source "drivers/net/ethernet/mellanox/Kconfig"
 source "drivers/net/ethernet/qlogic/Kconfig"
 source "drivers/net/ethernet/racal/Kconfig"
 source "drivers/net/ethernet/sfc/Kconfig"

drivers/net/ethernet/Makefile

@@ -11,6 +11,7 @@ obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
 obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
 obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
+obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
 obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
 obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
 obj-$(CONFIG_SFC) += sfc/

drivers/net/ethernet/mellanox/Kconfig

+#
+# Mellanox driver configuration
+#
+
+config NET_VENDOR_MELLANOX
+	bool "Mellanox devices"
+	depends on PCI && INET
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Mellanox cards. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_MELLANOX
+
+source "drivers/net/ethernet/mellanox/mlx4/Kconfig"
+
+endif # NET_VENDOR_MELLANOX

drivers/net/ethernet/mellanox/Makefile

+#
+# Makefile for the Mellanox device drivers.
+#
+
+obj-$(CONFIG_MLX4_CORE) += mlx4/

drivers/net/ethernet/mellanox/mlx4/Kconfig

+#
+# Mellanox driver configuration
+#
+
+config MLX4_EN
+	tristate "Mellanox Technologies 10Gbit Ethernet support"
+	depends on PCI && INET
+	select MLX4_CORE
+	select INET_LRO
+	---help---
+	  This driver supports Mellanox Technologies ConnectX Ethernet
+	  devices.
+
+config MLX4_CORE
+	tristate
+	depends on PCI
+	default n
+
+config MLX4_DEBUG
+	bool "Verbose debugging output" if (MLX4_CORE && EXPERT)
+	depends on MLX4_CORE
+	default y
+	---help---
+	  This option causes debugging code to be compiled into the
+	  mlx4_core driver.  The output can be turned on via the
+	  debug_level module parameter (which can also be set after
+	  the driver is loaded through sysfs).