- 30 3月, 2021 9 次提交
-
-
由 Amit Kumar Mahapatra 提交于
Update the following device tree properties for nand flash - Set software ecc mode. - Set bch as ecc algo. - Set read block to 0. Signed-off-by: NAmit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Update clock/pll setup, ddr, MIOs based on 2020.2 hw design. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is Linux driver for these chips that's why add it to device tree. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Add missing configurations file for zcu208 and zcu216. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ashok Reddy Soma 提交于
EMMC will have bus-width 8 and it is non-removable in general. These are missing from dt node. Add bus-width and non-removable parameters to emmc node. Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ashok Reddy Soma 提交于
size of malloc() pool for use before relocation is not sufficient for ZynqMP mini u-boot with emmc configuration. Increase it to 4K. Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ashok Reddy Soma 提交于
Enable time command to get the elapsed time and timer commands. Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Robert Hancock 提交于
The code was trying to disable PCS auto-negotiation when a fixed-link node is present and enable it otherwise. However, the PCS registers were being written before the PCSSEL bit was set in the network configuration register, and it appears that in this state, PCS register writes are ignored. The result is that the intended change only took effect on the second network operation that was performed, since at that time PCSSEL is already enabled. Fix the order of register writes so that PCS registers are only written to after the PCS is enabled. Fixes: 26e62cc9 ("net: gem: Disable PCS autonegotiation in case of fixed-link") Signed-off-by: NRobert Hancock <robert.hancock@calian.com> Reviewed-by: NRamon Fried <rfried.dev@gmail.com> Reviewed-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 29 3月, 2021 4 次提交
-
-
由 Tom Rini 提交于
-
由 Jessica Clarke 提交于
On Arm-based Macs, -no_pie is ignored and gives a linker warning. Moreover, the build falls over with: ld: Absolute addressing not allowed in arm64 code but used in '_image_type_ptr_aisimage' referencing '_image_type_aisimage' for dumpimage and mkimage, since we put data structs in text sections not data sections and so cannot have dynamic relocations. Instead, move the sections to __DATA and drop disabling PIE. Signed-off-by: NJessica Clarke <jrtc27@jrtc27.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Sean Anderson 提交于
We need this header for U_BOOT_CMD, which is always present even without EFI. Fixes: 82c468a0 ("dm: test: Update Makefile conditions") Signed-off-by: NSean Anderson <seanga2@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
When including this file on a board other than sandbox (e.g by enabling UNIT_TEST and CMD_SETEXPR) an results. Fix it by declaring struct udevice first. Signed-off-by: NSimon Glass <sjg@chromium.org> Reported-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
- 27 3月, 2021 15 次提交
-
-
由 Tom Rini 提交于
- Rework the deprecation warnings to be consistently phrased. - Add in a warning for DM_I2C, for a year from next release. - Fix Azure builds of Windows host tools.
-
由 Tom Rini 提交于
We now see an error such as: warning: database file for 'ucrt64' does not exist (use '-Sy' to download) error: failed to prepare transaction (could not find database) So use -Sy as suggested. Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Simon Glass 提交于
This probably should have been done a while back since it is a core system. Add a migration deadline of later this year, to catch the stragglers. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This message does not seem to make sense. It may be out of date. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the CONFIG_DM_ETH check to use the 'deprecated' function. Tested with snow Old message: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the CONFIG_WDT check to use the 'deprecated' function. Tested with kmcent2 Old message: ===================== WARNING ====================== This board does not use CONFIG_WDT (DM watchdog support). Please update the board to use CONFIG_WDT before the v2019.10 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_WDT (Driver Model for DM watchdog). Please update the board to use CONFIG_WDT before the v2019.10 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the CONFIG_DM_SPI_FLASH check to use the 'deprecated' function. Tested with vinco Old message: ===================== WARNING ====================== This board does not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_DM_SPI_FLASH (Driver Model for SPI flash). Please update the board to use CONFIG_DM_SPI_FLASH before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the CONFIG_DM_VIDEO check to use the 'deprecated' function. Tested with pxm2 Old message: ===================== WARNING ====================== This board does not use CONFIG_DM_VIDEO Please update the board to use CONFIG_DM_VIDEO before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_DM_VIDEO (Driver Model for video). Please update the board to use CONFIG_DM_VIDEO before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the CONFIG_DM_PCI check to use the 'deprecated' function. Tested with MPC8349ITX Old message: ===================== WARNING ====================== This board does not use CONFIG_DM_PCI Please update the board to use CONFIG_DM_PCI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_DM_PCI (Driver Model for PCI). Please update the board to use CONFIG_DM_PCI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the CONFIG_LIBATA check to use the 'deprecated' function. Tested with MPC8349ITX Old message: ===================== WARNING ====================== This board does use CONFIG_LIBATA but has CONFIG_AHCI not enabled. Please update the storage controller driver to use CONFIG_AHCI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_AHCI (Driver Model for AHCI). Please update the board to use CONFIG_AHCI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the CONFIG_MVSATA_IDE check to use the 'deprecated' function. Tested with nas220 Old message: ===================== WARNING ====================== This board does use CONFIG_MVSATA_IDE which is not ported to driver-model (DM) yet. Please update the storage controller driver to use CONFIG_AHCI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_AHCI (Driver Model for AHCI instead of CONFIG_MVSATA_IDE). Please update the board to use CONFIG_AHCI before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the USB check to use the 'deprecated' function. Tested with xpress Old message: ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_DM_USB (Driver Model for USB). Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Update the MMC check to use the 'deprecated' function. Tested with zc5202 Old message: ===================== WARNING ====================== This board does not use CONFIG_DM_MMC. Please update the board to use CONFIG_DM_MMC before the v2019.04 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== New message: ===================== WARNING ====================== This board does not use CONFIG_DM_MMC (Driver Model for MMC). Please update the board to use CONFIG_DM_MMC before the v2019.04 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Add a function which can be called to report a migration problem. This will make it easier to add new migration checks, since the logic and strings are not spread out over 8 lines of code. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present the driver model migration messages are mixed with the others. Collect them together before starting to refactor them. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 24 3月, 2021 1 次提交
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq由 Tom Rini 提交于
- Bug fixes related to FSL-IFC, watchdog - layerscape-pcie, flexspi, T2080rdb.
-
- 23 3月, 2021 11 次提交
-
-
由 Maxim Kochetkov 提交于
Linux commit a75bbe71a27 ("mtd: rawnand: fsl_ifc: fix FSL NAND driver to read all ONFI parameter pages") Per ONFI specification (Rev. 4.0), if the CRC of the first parameter page read is not valid, the host should read redundant parameter page copies. Fix FSL NAND driver to read the two redundant copies which are mandatory in the specification. Signed-off-by: NJane Wan <Jane.Wan@nokia.com> Signed-off-by: NBoris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: NMaxim Kochetkov <fido_max@inbox.ru> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Hou Zhiqiang 提交于
As on some incipient Layerscape platforms (LS1043A series) there isn't separate PF control register block, these registers reside in the LUT register block, so when the driver detected there isn't 'ctrl', it will assign the 'lut' address to the ls_pcie->ctrl. The current code allocate memory for the struct ls_pcie with random contents, this can result in skipping to assign the ls_pcie->ctrl with the 'lut' address, then further crash with the incorrect address. Fixes: 118e58e2 ("pci: layerscape: Split the EP and RC driver") Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NVladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
LS1028A-RDB/QDS has Micron "mt35xu02g" nor flash of size 256M with 128K sector size. Correct CONFIG_ENV_SECT_SIZE value to 128K. Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
LS1028A-QDS has CONFIG_SPI_FLASH_SST and CONFIG_SPI_FLASH_EON defines present in header. Move these entries from header to defconfigs. Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
There is no Spansion flash on LS1028A-RDB/QDS boards. Unset CONFIG_SPI_FLASH_SPANSION option for both the boards. Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
It is now safe to remove Flexspi configs NXP_FSPI_FLASH_SIZE and NXP_FSPI_FLASH_NUM options from headers as they are no longer used by driver anymore. Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
There is no Spansion flash on LX2160A-RDB/QDS boards. Unset CONFIG_SPI_FLASH_SPANSION option for both the boards. Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Chris Packham 提交于
The User Guide contains handy things like block diagrams and DIP switch settings and it's even available on the public web. Add a link to it in the README. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Chris Packham 提交于
The T2080RDB has a ds1339 on i2c0. Add this to the devicetree and enable the relevant support in the configs. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Chris Packham 提交于
As far as u-boot is concerned the ds1339 is compatible with the other devices supported by the ds1307 driver. The Linux driver does expose some additional functionality but as far as u-boot is concerned just adding the compatible string is enough. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
-