- 29 11月, 2011 8 次提交
-
-
由 Timur Tabi 提交于
On the P1022/P1013, the work-around for erratum SATA_A001 was implemented only if U-Boot initializes SATA, but SATA is not initialized by default. So move the work-around to the CPU initialization function, so that it's always executed on the SOCs that need it. Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Timur Tabi 提交于
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA controller, so it should be defined in config_mpc85xx.h instead of the various board header files. So now CONFIG_FSL_SATA_V2 is always defined on the P1013, P1022, P2041, P3041, P5010, and P5020. It was already defined for the P1010 and P1014. Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 York Sun 提交于
Erratum A-003474: Internal DDR calibration circuit is not supported Impact: Experience shows no significant benefit to device operation with auto-calibration enabled versus it disabled. To ensure consistent timing results, Freescale recommends this feature be disabled in future customer products. There should be no impact to parts that are already operating in the field. Workaround: Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following: 1. Write a value of 0x0000_0015 to the register at offset CCSRBAR + DDR OFFSET + 0xf30 2. Write a value of 0x2400_0000 to the register at offset CCSRBAR + DDR OFFSET + 0xf54 Signed-off-by: NYork Sun <yorksun@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Jia Hongtao 提交于
Make the fixup matchable with dts and kernel. Update the compatible from "fsl,flexcan-v1.0" to "fsl,p1010-flexcan" and Change the "clock-freq" property to "clock-frequency". We also change flexcan frequency from CCB-clock to CCB-clock/2 according to P1010 spec. We now keep the old interfaces to make previous kernel work. They should be removed in the future. Signed-off-by: NJia Hongtao <B38951@freescale.com> Signed-off-by: NLi Yang <leoli@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Erratum A-003999: Running Floating Point instructions requires special initialization. Impact: Floating point arithmetic operations may result in an incorrect value. Workaround: Perform a read modify write to set bit 7 to a 1 in SPR 977 before executing any floating point arithmetic operation. This bit can be set when setting MSR[FP], and can be cleared when clearing MSR[FP]. Alternatively, the bit can be set once at boot time, and never cleared. There will be no performance degradation due to setting this bit. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Wolfgang Denk 提交于
common/menu.c used printf() in a number of places to print user provided, constant strings (like the "title" string). printf() is dangerous here for example in case the user unwittingly embeds some '%' caracters that printf() would interpret as formatting and then pick up random arguments. Use puts() instead. We also omit the trailing ':' in the title line - if a user wants this, he can provide it as part of the title string. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
git://git.denx.de/u-boot-staging由 Wolfgang Denk 提交于
* 'agust@denx.de' of git://git.denx.de/u-boot-staging: MAKEALL: drop obsolete mx31pdk_nand target dataflash: fix parameters order in write_dataflash() hawkboard: Replace HAWKBOARD_KICK{0, 1}_UNLOCK defines davinci_sonata: define CONFIG_MACH_TYPE for davinci_sonata board davinci_schmoogie: define CONFIG_MACH_TYPE for davinci_schmoogie board arm: a320evb: define mach-type in board config file OMAP3: Use sdelay from arch/arm/cpu/armv7/syslib.c instead of cloning that. Fix Stelian's email address
-
git://git.denx.de/u-boot-video由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-video: DIU: 1080P and 720P support CFB: Fix font rendering on mx5 framebuffer
-
- 28 11月, 2011 8 次提交
-
-
由 Stefano Babic 提交于
The mx31pdk can boot only from NAND and the target was already updated in boards.cfg. mx31pdk_nand is obsolete and is dropped. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Igor Grinberg 提交于
Fix parameters order in write_dataflash() function extern declaration in the header file. Parameters order, as in function definition, should be: addr_dest, addr_src, size. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
-
由 Christian Riesch 提交于
This patch replaces the HAWKBOARD_KICK{0,1}_UNLOCK defines by DV_SYSCFG_KICK{0,1}_UNLOCK. The kick register values are not hawkboard specific but may be used for all davinci boards. In commit f3c149d6 new defines for these values wer introduced. Signed-off-by: NChristian Riesch <christian.riesch@omicron.at> Cc: Syed Mohammed Khasim <sm.khasim@gmail.com> Cc: Sughosh Ganu <urwithsughosh@gmail.com> Cc: Sandeep Paulraj <s-paulraj@ti.com>
-
由 Christian Riesch 提交于
This patch fixes the build breakage for the davinci_sonata board. Signed-off-by: NChristian Riesch <christian.riesch@omicron.at> Cc: Sergey Kubushyn <ksi@koi8.net> Cc: Sandeep Paulraj <s-paulraj@ti.com>
-
由 Christian Riesch 提交于
This patch fixes the build breakage for the davinci_schmoogie board. Signed-off-by: NChristian Riesch <christian.riesch@omicron.at> Cc: Sergey Kubushyn <ksi@koi8.net> Cc: Sandeep Paulraj <s-paulraj@ti.com>
-
由 Yan-Pai Chen 提交于
MACH_TYPE_FARADAY was dropped from mach-types.h. Add it back to board config file. Signed-off-by: NYan-Pai Chen <ypchen@faraday-tech.com> Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
-
由 Alexander Holler 提交于
There is no need to have such a function twice. Signed-off-by: NAlexander Holler <holler@ahsoftware.de> Acked-by: NDirk Behme <dirk.behme@googlemail.com> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Stelian Pop 提交于
Change my old email address which is no longer valid. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 27 11月, 2011 6 次提交
-
-
git://git.denx.de/u-boot-mmc由 Wolfgang Denk 提交于
* 'master' of git://git.denx.de/u-boot-mmc: Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec" mmc: mv_sdhci: Fix host version read for Armada100
-
由 Stephan Linz 提交于
As a result of the commit 68332608 the uart16550 driver is broken for Microblaze big endian systems, because of the missing 3 byte offset. Other than as described, not all U-Boot BSP will treat properly the 3 byte offset. This why prefer to mask out the 3 byte offset in general and setup correct _REG_SIZE value depending on edianess. Signed-off-by: NStephan Linz <linz@li-pro.net> Tested-by: NMichal Simek <monstr@monstr.eu>
-
由 Michael Jones 提交于
Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
-
由 Kumar Gala 提交于
cmd_nvedit.c: In function 'do_env_grep': cmd_nvedit.c:182:3: warning: suggest parentheses around assignment used as truth value Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Acked-by: NMike Frysinger <vapier@gentoo.org> Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
-
由 Kumar Gala 提交于
Fix: x86emu/ops2.c: In function 'x86emuOp2_set_byte': x86emu/ops2.c:171:11: warning: variable 'name' set but not used [-Wunused-but-set-variable] Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Mike Frysinger 提交于
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 26 11月, 2011 2 次提交
-
-
由 Macpaul Lin 提交于
This reverts commit 02f3029f. This patch add 3 times retry to CMD8 because the Marvell mmc controller doesn't obey the power ramp up process in the SD specification 6.4.1. (Please refer to figure 6.1 and 6.2 in the specification.) The CMD0 should be send after power ramp up has been finished. However, the Marvell mmc contorller must do power ramp up after the first CMD0 command has been send. This patch also affect existing platforms like Nokia N900 and other platforms. Signed-off-by: NMacpaul Lin <macpaul@andestech.com> Acked-by: NLei Wen <leiwen@marvell.com> Acked-by: NStephen Warren <swarren@nvidia.com> Tested-by: NStephen Warren <swarren@nvidia.com>
-
由 Ajay Bhargav 提交于
sdhci_readw does not work for host version read in Armada100 series SoCs. This patch fix this issue by making a sdhci_readl call to get host version. Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>
-
- 25 11月, 2011 2 次提交
-
-
由 Jerry Huang 提交于
Add the 1920x1080 and 1280x720 resolution support. Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com> Acked-by: NTimur Tabi <timur@freescale.com> CC: Anatolij Gustschin <agust@denx.de>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
- 24 11月, 2011 4 次提交
-
-
git://git.denx.de/u-boot-staging由 Wolfgang Denk 提交于
* 'hs@denx.de' of git://git.denx.de/u-boot-staging: drivers/net/dnet.c: Fix GCC 4.6 warnings board/xaeniax/flash.c: Fix GCC 4.6 warnings net/bootp.c: Fix GCC 4.6 warning common/cmd_bootm.c: Fix GCC 4.6 warnings board/mx1ads/mx1ads.c: Fix GCC 4.6 warning board/mx1ads/syncflash.c: Fix GCC 4.6 warnings board/lubbock/flash.c: Fix GCC 4.6 warnings drivers/net/cs8900.c: Fix GCC 4.6 warning arch/arm/cpu/arm926ejs/omap/cpuinfo.c: Fix GCC 4.6 warnings drivers/net/lan91c96.c: Fix GCC 4.6 warning board/ronetix/pm9263/pm9263.c: Fix GCC 4.6 warning drivers/mtd/onenand/samsung.c: Fix GCC 4.6 warning drivers/usb/musb/musb_hcd.c: Fix GCC 4.6 warning
-
由 Anatolij Gustschin 提交于
Fix: davinci_i2c.c: In function 'flush_rx': davinci_i2c.c:81:6: warning: variable 'dummy' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de> Acked-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
There are some magic constants in this drivers, which I cannot fixup ... Eran, can you help here? Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Eran Man <eran@nbase.co.il>
-
由 Nobuhiro Iwamatsu 提交于
This supports I2C of Renesas SH. I tested on SH7724. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Heiko Schocher <hs@denx.de>
-
- 23 11月, 2011 10 次提交
-
-
由 Anatolij Gustschin 提交于
Fix: dnet.c: In function 'dnet_send': dnet.c:136:9: warning: variable 'len' set but not used [-Wunused-but-set-variable] dnet.c: In function 'dnet_set_hwaddr': dnet.c:209:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] dnet.c:209:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] dnet.c:209:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] dnet.c:209:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: flash.c: In function 'flash_erase': flash.c:223:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] flash.c: In function 'write_data': flash.c:392:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: bootp.c: In function 'BootpCopyNetParams': bootp.c:108:11: warning: unused variable 'tmp_ip' [-Wunused-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: cmd_bootm.c: In function 'bootm_load_os': cmd_bootm.c:315:7: warning: unused variable 'unc_len' [-Wunused-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: mx1ads.c: In function 'board_early_init_f': mx1ads.c:83:24: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: syncflash.c: In function 'SF_SR': syncflash.c:60:10: warning: variable 'tmp1' set but not used [-Wunused-but-set-variable] syncflash.c: In function 'SF_PrechargeAll': syncflash.c:96:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] mx1ads.c: In function 'board_early_init_f': mx1ads.c:83:24: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] syncflash.c: In function 'SF_Erase': syncflash.c:112:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] syncflash.c: In function 'flash_init': syncflash.c:155:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: flash.c: In function 'flash_erase': flash.c:223:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] flash.c: In function 'write_data': flash.c:392:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: cs8900.c: In function 'get_reg_init_bus': cs8900.c:69:14: warning: variable 'c' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: cpuinfo.c: In function 'print_cpuinfo': cpuinfo.c:155:6: warning: variable 'system_serial_low' set but not used [-Wunused-but-set-variable] cpuinfo.c:154:6: warning: variable 'system_serial_high' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Fix: lan91c96.c: In function 'dump_memory_info': lan91c96.c:157:7: warning: variable 'mem_info' set but not used [-Wunused-but-set-variable] lan91c96.c: In function 'smc_send_packet': lan91c96.c:320:16: warning: variable 'ioaddr' set but not used [-Wunused-but-set-variable] Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-