- 02 7月, 2009 1 次提交
-
-
由 Poonam Aggrwal 提交于
Defining the next two configs allows to switch the serial port from the console using the setenv stdin and stdout 1. #define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */ 2. #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 13 6月, 2009 1 次提交
-
-
由 Tom Rix 提交于
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board. The default serial is from the USB connector on left side of the debug board. The USB connector will produce 2 of the 4 UARTS. On your host pick the first enumeration. The details of the setting of the serial gpmc setup are not available. The values were provided by another party. The serial port set up is the same with Zoom1. Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow. The kernel bootargs are console=ttyS3,115200n8 Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 19 10月, 2008 1 次提交
-
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 05 2月, 2008 1 次提交
-
-
由 Harald Welte 提交于
This patch adds support for CONFIG_SERIAL_MULTI on s3c24x0 CPU's Signed-off-by: NHarald Welte <laforge@openmoko.org>
-
- 01 11月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 07 9月, 2007 1 次提交
-
-
由 stefano babic 提交于
This patch adds support for multiple serial ports to the PXA target. FFUART, BTUART and STUART are supported. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
- 24 3月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
This patch cleans up all the open issue of the preliminary Acadia support. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 31 8月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 16 6月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
Patch by Martin Krause, 8 Jun 2006 This patch supports two serial consoles on boards with a MPC5xxx CPU. The console can be switched at runtime by setting stdin, stdout and stderr to the desired serial interface (serial0 or serial1). The PSCs to be used as console port are definded by CONFIG_PSC_CONSOLE and CONFIG_PSC_CONSOLE2. See README.serial_multi for details.
-
- 10 1月, 2005 1 次提交
-
-
由 wdenk 提交于
add support for the AMD db1550 board * Patch by Travis Sawyer, 15 Sep 2004: Add CONFIG_SERIAL_MULTI support for ppc4xx, update README.serial_multi
-
- 02 8月, 2004 1 次提交
-
-
由 wdenk 提交于
* Patch by Sascha Hauer, 28 Jun: - add generic support for Motorola i.MX architecture - add support for mx1ads, mx1fs2 and scb9328 boards * Patches by Marc Leeman, 23 Jul 2004: - Add define for the PCI/Memory Buffer Configuration Register - corrected comments in cpu/mpc824x/cpu_init.c * Add support for multiple serial interfaces (for example to allow modem dial-in / dial-out)
-