- 04 2月, 2020 14 次提交
-
-
由 Biwen Li 提交于
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1021A Signed-off-by: NBiwen Li <biwen.li@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Biwen Li 提交于
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1012A Signed-off-by: NBiwen Li <biwen.li@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
Enable FSPI controller support. So, flash environment can now be used Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
Enable the config for ls1012ardb as the entry got missed earlier. Fixes: 8d8ee47e ("env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol") Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Faiz Abbas 提交于
Enable CONFIG_DA8XX_GPIO to enable GPIO support. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vignesh Raghavendra 提交于
Enable PCA953x IO expander to control MMC/SD power lines. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vignesh Raghavendra 提交于
Enable DFU, Fastboot and USB mass storage gadget related configs Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vignesh Raghavendra 提交于
Enable USB Gadget for R5 SPL, A72 SPL and A72 U-Boot to support DFU boot Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vignesh Raghavendra 提交于
Increase R5 SPL early malloc memory pool by ~7K to accommodate SPL USB DFU boot requirements Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Faiz Abbas 提交于
The current environment offset overlaps with the sysfw area and whenever environment is saved in the redundant slot, it overwrites sysfw.itb. Fix the offset to prevent this. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Sam Protsenko 提交于
Enable Android commands that will be needed for Android 10 boot flow implementation, for all AM57x variants. Commands enabled: 1. 'abootimg': - CONFIG_CMD_ABOOTIMG=y 2. 'ab_select': - CONFIG_ANDROID_AB=y - CONFIG_CMD_AB_SELECT=y 3. 'avb': - CONFIG_LIBAVB=y - CONFIG_AVB_VERIFY=y - CONFIG_CMD_AVB=y While at it, resync defconfig files with "make savedefconfig". Signed-off-by: NSam Protsenko <joe.skb7@gmail.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Sam Protsenko 提交于
Unit test for 'abootimg' command. Right now it covers dtb/dtbo functionality in Android Boot Image v2, which was added recently. Running test: $ ./test/py/test.py --bd sandbox --build -k test_abootimg shows that 1/1 tests passes successfully. Signed-off-by: NSam Protsenko <joe.skb7@gmail.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Andy Shevchenko 提交于
SFI is quite poor and useless resource provider. Moreover it makes hard to develop and extend functionality in the Linux kernel. Enable a necessary minimum to use ACPI on Intel Edison. Linux kernel have been prepared for this change since v5.4, where the last crucial driver, i.e. for Basin Cove PMIC, has been submitted. Note, that stock image won't suffer by this change since it doesn't have ACPI enabled on the kernel level. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Marek Vasut 提交于
Enable command line editing, because it is extremely convenient. Signed-off-by: NMarek Vasut <marex@denx.de> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
- 30 1月, 2020 8 次提交
-
-
由 Mark Kettenis 提交于
This enables readning the cpuid from e-fuse, and deriving a static MAC address from it. Signed-off-by: NMark Kettenis <kettenis@openbsd.org> Reviewed-by: NKever Yang <kever.yang@rock-chips.com>
-
由 Kever Yang 提交于
Rockchip use CONFIG_SPL_OPTEE for OPTEE support, which is load and run before U-Boot, but not use CONFIG_OPTEE which is after U-Boot. Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
-
由 Jagan Teki 提交于
All rockchip platforms support TPL or SPL-based bootloader in mainline with U-Boot proper as final stage. For each stage we need to burn the image on to flash with respective offsets. This patch creates a single boot image component using - binman, for arm32 rockchip platforms - pad_cat, for arm64 rockchip platforms. This would help users to get rid of burning different boot stage images. The new image called 'u-boot-rockchip.bin' which can burn into flash like: ₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64 This would support all rockchip platforms, except rk3128 since it doesn't support for SPL yet. Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Cc: Wadim Egorov <w.egorov@phytec.de> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NKever Yang <kever.yang@rock-chips.com>
-
由 Jagan Teki 提交于
RK3288, RK3399 are now support cpu-info, so enable DISPLAY_CPUINFO by default. Reviewed-by: NKever Yang <kever.yang@rock-chips.com> Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
Enable winbond SPI flash for ROC-PC-RK3399 board. Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NKever Yang <kever.yang@rock-chips.com>
-
由 Jagan Teki 提交于
Enable winbond SPI flash for ROC-PC-RK3399 board. Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NKever Yang <kever.yang@rock-chips.com>
-
由 Amit Singh Tomar 提交于
The Raspberry Pi 4 SoC features an integrated Gigabit Ethernet controller, connected as a platform device. Enable the new driver in the three applicable defconfigs, to allow TFTP booting on the board. Signed-off-by: NAmit Singh Tomar <amittomer25@gmail.com> [Andre: Add joined and 32-bit configs] Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Tested-by: NCorentin Labbe <clabbe@baylibre.com> Signed-off-by: NMatthias Brugger <mbrugger@suse.com>
-
由 Marek Szyprowski 提交于
Enable support for DFU over USB. This requires to enable USB gadget, DWC2 UDC OTG driver and DFU command. DFU entities are defined for the following firmware objects: u-boot.bin, uboot.env, config.txt, and zImage/Image. Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: NLukasz Majewski <lukma@denx.de> Signed-off-by: NMatthias Brugger <mbrugger@suse.com>
-
- 28 1月, 2020 2 次提交
-
-
由 Anatolij Gustschin 提交于
This shrinks the image size: all -3840.0 text -3840.0 Signed-off-by: NAnatolij Gustschin <agust@denx.de> Acked-by: NSoeren Moch <smoch@web.de>
-
由 Marek Szyprowski 提交于
XOM pins provide information for iROM bootloader about the boot device. Those pins are mapped to lower bits of OP_MODE register (0x10000008), which is common for all Exynos SoC variants. Set the default MMC device id to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for the eMMC). Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 26 1月, 2020 4 次提交
-
-
由 Jernej Skrabec 提交于
Orange Pi Win has gigabit ethernet port, but default U-Boot configuration for that board enabled ethernet driver but didn't enable realtek phy. Fix that. Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 mingming lee 提交于
This patch includes the following: 1. Add fastboot command to erase the whole EMMC_USER 2. Add fastboot command to flash image at EMMC_BOOT1 3. Add fastboot command to erase the whole EMMC_BOOT1 4. Enale CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT for mt8518 Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>
-
由 mingming lee 提交于
Enable EFI module. Enable fastboot. Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>
-
由 mingming lee 提交于
Enable board_late_init and usb gadget for mt8518 Signed-off-by: Nmingming lee <mingming.lee@mediatek.com>
-
- 25 1月, 2020 5 次提交
-
-
由 Chen-Yu Tsai 提交于
The Libre Computer ALL-H5-CC board is an upgraded version of the ALL-H3-CC. Changes include: - Gigabit Ethernet via external RTL8211E Ethernet PHY - 16 MiB SPI NOR flash memory - PoE tap header - Line out jack removed Only H5 variant test samples were made available, and the vendor is not certain whether other SoC variants would be made or not. Furthermore the board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree simply includes the one for the ALL-H3-CC, and adds the changes on top. The device tree was synced over from the Linux kernel, along with other H3/H5 changes, in a previous patch. Thus only the defconfig and an entry to the MAINTAINERS file is added. Signed-off-by: NChen-Yu Tsai <wens@csie.org> [jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS] Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Chen-Yu Tsai 提交于
The Libre Computer ALL-H3-IT board is a small single board computer that is roughly the same size as the Raspberry Pi Zero, or around 20% smaller than a credit card. The board features: - H2, H3, or H5 SoC from Allwinner - 2 DDR3 DRAM chips - Realtek RTL8821CU based WiFi module - 128 Mbit SPI-NOR flash - micro-SD card slot - micro HDMI video output - FPC connector for camera sensor module - generic Raspberri-Pi style 40 pin GPIO header - additional pin headers for extra USB host ports, ananlog audio and IR receiver Only H5 variant test samples were made available, but the vendor does have plans to include at least an H3 variant. Thus the device tree is split much like the ALL-H3-CC, with a common dtsi file for the board design, and separate dts files including the common board file and the SoC dtsi file. The other variants will be added as they are made available. The device tree was synced over from the Linux kernel, along with other H3/H5 changes, in a previous patch. Thus only the defconfig and an entry to the MAINTAINERS file is added. Signed-off-by: NChen-Yu Tsai <wens@csie.org> [jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS] Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Andre Przywara 提交于
For Allwinner SoCs the CONFIG_SYS_SPI_U_BOOT_OFFS value is not really a board choice: The boot ROM only loads the SPL from offset 0 of the SPI NOR flash, and loads at most 32KB. This is a similar situation as on MMC, so consequently we create our "joint" image (SPL + U-Boot proper) with that 32KB offset during the build. So define the value of this symbol to be 32KB by default for every Allwinner SoC. This removes the definition of this symbol from the _defconfig files, and avoids every board to define this over and over again. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Andre Przywara 提交于
Now that the USB PHY on the Allwinner R40 SoC is supported, enable USB support for the two R40 boards U-Boot supports. For this we need to add the GPIO pin that powers the USB port(s), also enable the usual suspects (OHCI/EHCI support). Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Andre Przywara 提交于
The M2 Berry features the normal Gigabit PHY connected to the SoC's MAC, so enable the sun8i-emac driver to support Ethernet on the board. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>
-
- 24 1月, 2020 7 次提交
-
-
由 Alex Marginean 提交于
LS1028A QDS boards have a MDIO MUX and they require the driver for it for PHYs to work. Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Udit Agarwal 提交于
setexpr command is used while running secure boot (chain of trust with confidentiality) feature. Enable CONFIG_CMD_SETEXPR to enable setexpr command. Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Alex Marginean 提交于
Currently LS1028A board code uses arch_misc_init to set up the board mux on QDS. Move this code to misc_init_r. This is consistent with LS gen 2 and T series SoCs/boards. Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Alex Marginean 提交于
Currently LX2 board code uses arch_misc_init to set up the board mux on RDB and QDS. Move this code to misc_init_r. This is consistent with LS gen 2 and T series SoCs/boards. Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Wasim Khan 提交于
lx2160a rev1 and rev2 SoC has different pcie controller. The pcie controller device tree node fields "compatible" and registers names needs to be updated accordingly. Enable CONFIG_OF_BOARD_FIXUP to apply board_fix_fdt which updates the "compatible" and registers names. Signed-off-by: NWasim Khan <wasim.khan@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Wasim Khan 提交于
Add Common device tree fixup for NXP SoCs. Based on SoC and revision call pcie_layerscape or pcie_layerscape_gen4 fixup. Signed-off-by: NWasim Khan <wasim.khan@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Yinbo Zhu 提交于
Enable RTL8152, AX88179 and AX8817X USB network cards support for ls1012afwry Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-