- Bug fixes on ls1012a, ls1021a, ls1028ardb platforms Integrate fspi for
  ls1028a, add DM-I2C support, update secure boot header offset

- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config

- Various minor fixes for x86
- Switch to ACPI mode on Intel edison
- Support run-time configuration for NS16550 driver
- Update coreboot and slimbootloader serial drivers to use NS16550
run-time configuration
- ICH SPI driver fixes to hardware sequencing erase case
- Move ITSS from Apollo Lake to a more generic location
- Intel GPIO driver bug fixes
- Move to vs2017-win2016 platform build host for Azure pipelines

- DFU boot support for J721e
- I2C support for J721e
- GPIO support for J721e
- Android boot image updates on AM57XX
- OMAP watchdog fixes

Inside Kconfig we must not use the CONFIG_ prefix with the imply statement.

Fixes: 28e3c39e ("board: freescale: ls1012a2g5rdb: enable network
support on ls1012a2g5rdb")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Updates the secure boot headers offsets of Kernel and other
firmware images for SD and NOR boot sources used by
esbc_validate command.
Signed-off-by: NPriyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Updates the secure boot headers offsets of Kernel and other
firmware images for SD and QSPI boot sources used by
esbc_validate command.
Signed-off-by: NPriyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Updates the secure boot headers offsets of Kernel and other
firmware images for SD and XSPI boot sources used by
esbc_validate command.
Signed-off-by: NPriyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Updates the secure boot headers offsets of Kernel and other
firmware images used by esbc_validate command.
Signed-off-by: NPriyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Updates the secure boot headers offsets of Kernel and other
firmware images for SD and QSPI boot sources used by
esbc_validate command.
Signed-off-by: NPriyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

The default reserved memory for CMA is high memory. If LPAE is enabled,
highmem pages are non-remapped and can not be used with
dma_alloc_coherent. This patch will reserve low memory for CMA and fix
the issue on LS1021A.
Signed-off-by: NPeng Ma <peng.ma@nxp.com>
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: NAlison Wang <alison.wang@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

The default value of CONFIG_SYS_MALLOC_F_LEN (0x400)
leaves U-Boot with not enough memory to load i2c driver
before relocate, causing it to hang.

Change the default value of CONFIG_SYS_MALLOC_F_LEN
for below SoCs,
- LS1012A
- LS1021A
- LS1043A
- LS1046A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

This adds DM_FLAG_PRE_RELOC flag to probe i2c driver
before relocation
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Fix below SPL build error when DM_I2C is enabled,
- arch/arm/cpu/armv8/built-in.o: In function `board_init_f:
  arch/arm/cpu/armv8/fsl-layerscape/spl.c:74: undefined reference to `i2c_init_all'
  arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:(.text.board_init_f+0x30):
  relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol
  `i2c_init_all'
  make[2]: *** [spl/u-boot-spl] Error 1
  make[1]: *** [spl/u-boot-spl] Error 2
  make: *** [sub-make] Error 2
  arch/arm/cpu/armv8/fsl-layerscape/spl.c: In function 'board_init_f':
  arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:2: warning: implicit
  declaration of function 'i2c_init_all'; did you mean 'misc_init_r'?
  [-Wimplicit-function-declaration]`
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add support of driver model of pcf8563
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable FSPI controller support. So, flash environment can now be used
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Align flexspi node properties with linux device-tree properties
Tested on LX2160A-RDB
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Align flexspi node properties with linux device-tree properties
Tested on LS1028A-RDB
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add support of "qixis_reset emmc" command for lx2160a based platforms
Signed-off-by: NMeenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Sync the interrupt properties with the ones from Linux. Also use the
constants provided by the dt-bindings header. Please note, that there
are actual changes/fixes in the irq flags. U-Boot won't use the
interrupt properties anyway. It's just to be consistent with the Linux
device tree.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Also align the fspi node with the kernel one.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable the config for ls1012ardb as the entry got missed earlier.

Fixes: 8d8ee47e ("env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol")
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Azure is moving to remove the vs2015-win2012r2 platform build host.  The
two suggested new platforms to use are vs2017-win2016 and windows-2019.
For now, move up to vs2017-win2016.

Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Tested-by: NBin Meng <bmeng.cn@gmail.com>

Fix the following in intel_gpio_get_value():

 * The value of the register is contained in the variable 'reg', not in
   'mode'. The variable 'mode' contains only the configuration whether
   the gpio is currently an input or an output.

 * The correct bitmasks for the input and output value are
   PAD_CFG0_RX_STATE and PAD_CFG0_TX_STATE.
   Use them instead of the currently used PAD_CFG0_RX_STATE_BIT and
   PAD_CFG0_TX_STATE_BIT.
Signed-off-by: NWolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Add missing 'PAD_CFG0_TX_STATE' to the clear mask for pcr_clrsetbits32().
Otherwise this bit cannot be cleared again after it has been set once.
Signed-off-by: NWolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

The function pcr_clrsetbits32() expects a device with a P2SB parent
device. In intel_gpio_direction_output() and intel_gpio_set_value()
the device 'dev' is passed to pcr_clrsetbits32(), which is a
gpio-controller with a device 'pinctrl' as parent. This does not match
the expectations of pcr_clrsetbits32(). But the 'pinctrl' device has a
P2SB as parent.

Pass the 'pinctrl' device instead of the 'dev' device to
pcr_clrsetbits32().
Signed-off-by: NWolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

The Interrupt Timer Subsystem (ITSS) is not specific to Apollo Lake, so
remove the apl-prefix of the implemented functions/structures/...
Signed-off-by: NWolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Add a Kconfig option to support enabling/disabling the inclusion of
the ITSS driver depending on the platform.

Atuomatically select the ITSS driver when building for Apollo Lake.
Signed-off-by: NWolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
[bmeng: squashed in http://patchwork.ozlabs.org/patch/1232761/]
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>

The Interrupt Timer Subsystem (ITSS) is not specific to Apollo Lake, so
move it to a common location within arch/x86.
Signed-off-by: NWolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
[bmeng: conditionally build itss.c]
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>

Fix obvious coding style problems, no functional change.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

The watchdog timer value was never updated in the hardware by this
driver, so the watchdog triggered on some random stale value that
was left in the hardware. The TI SPRUH37C says, quote:

  20.4.3.9 Modifying Timer Count/Load Values and Prescaler Setting
  ...
  After a write access, the load register value and prescaler ratio
  registers are updated immediately, but new values are considered
  only after the next consecutive counter overflow or after a new
  trigger command (the WDT_WTGR register).

This means at least one trigger must happen. The driver probably
depended on someone calling it's .reset() callback, however that
is not guaranteed e.g. if the WDT operates without servicing.

Add this missing trigger.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

The timeout parameter of omap3_wdt_start() is in miliseconds, while
GET_WLDR_VAL() expects parameter in seconds. Fix this so the WDT
driver is actually usable.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable CONFIG_DA8XX_GPIO to enable GPIO support.
Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Add the main_gpio0 node.
Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Add "ti,keystone-gpio" compatible so as be able to use Linux DT files as
is.
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Fix below compiler warning for 64bit builds

drivers/gpio/da8xx_gpio.c: In function ‘davinci_get_gpio_bank’:
drivers/gpio/da8xx_gpio.c:446:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  return (struct davinci_gpio *)addr;
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable PCA953x IO expander to control MMC/SD power lines.
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

IO expanders are required to power cycle SD card. So enable the same
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>