- 02 9月, 2017 13 次提交
-
-
由 Stefan Roese 提交于
Without ethernet cable plugged, "ip=dhcp" leads to a complete hangup in Linux booting and the system does not boot into userland at all. Since its not required to have an active network connection on these board, lets remove this statement from the default environment. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bin Meng 提交于
It was noticed a few times, that the reboot from Linux (reboot command) is different from the reboot (reset command) under U-Boot. The U-Boot version does seem to reset the board more deeply (PCI cards etc) than the Linux reboot. This is actually caused by missing full reset bit in the reset register value in the ACPI FADT table. Reported-by: NStefan Roese <sr@denx.de> Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Tested-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
The atomic preop register can only be written when SPI settings are not locked, otherwise it's read-only. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Bin Meng 提交于
In ich_spi_xfer() when the driver presets control fields, control variable gets assigned twice. Apparently only the last assignment takes effect. Remove the other one. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_BCH Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_SPL_OMAP3_ID_NAND Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_SYS_I2C_BUS_MAX Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NHeiko Schocher <hs@denx.de> [trini: Fix AM43XX drop AM44XX] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
For consistency with other platforms and in preparation of Kconfig migration, let's change Several TI platforms that use I2C_BUS_MAX to CONFIG_SYS_I2C_BUS_MAX Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Tom Rini 提交于
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's not strictly part of fastboot. - Add some defaults for the fastboot buffer location and size - Migrate all options listed in cmd/fastboot/Kconfig - Cleanup the README Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: NTom Rini <trini@konsulko.com>
-
git://git.denx.de/u-boot-video由 Tom Rini 提交于
This reverts commit 1d201704, reversing changes made to 6aee2ab6. The mxc_ipuv3_fb.c changes introduce build failures on some targets. Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
-
- 01 9月, 2017 6 次提交
-
-
由 Dave Prue 提交于
SUNXI_GMAC was still used to configure the code where as the same has been renamed and moved to Kconfig in below commit "sunxi: Move SUNXI_GMAC to Kconfig" (sha1: 4d43d065) Signed-off-by: NDave Prue <dave@prue.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NJagan Teki <jagan@openedev.com> Reviewed-by: NMark Kettenis <kettenis@openbsd.org> Tested-by: NMark Kettenis <kettenis@openbsd.org> [Tweek commit message, config_whitelist.txt, build-whitelist.sh] Signed-off-by: NJagan Teki <jagan@openedev.com>
-
git://git.denx.de/u-boot-imx由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com> Conflicts: configs/imx6qdl_icore_mmc_defconfig configs/imx6qdl_icore_rqs_defconfig
-
-
git://git.denx.de/u-boot-uniphier由 Tom Rini 提交于
- add {ofnode,dev}_read_resource_byname - provide DT probe hook to Denali NAND driver - update clk/reset driver - update DT - misc cleanups
-
-
由 Chen-Yu Tsai 提交于
When enabling the new mmc timing mode, we inadvertently clear all the remaining bits in the new timing mode register. The bits cleared include a default phase delay on the output clock. The BSP kernel states that the default values are supposed to be used. Clearing them results in decreased performance or transfer errors on some boards. Fixes: de9b1771 ("mmc: sunxi: Support new mode") Signed-off-by: NChen-Yu Tsai <wens@csie.org> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
- 30 8月, 2017 20 次提交
-
-
由 Jagan Teki 提交于
Add Falcon mode support in Engicam i.CoreM6 board. Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
Memory dt node update introduced by spl_fixup_fdt() in below commit was making DDR configuration in-appropriate to boot falcon mode. Hence added dram_init_banksize for explicit assignment of proper base and size of DDR. "boot: fdt: Perform arch_fixup_fdt() on the given device tree for falcon boot" (sha1: 6e7585bb) Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Stefan Agner 提交于
The NXP i.MX 6UL and 6ULL do not support SATA and have no SATA boot mode, hence remove it from the boot device detecion. This fixes a build error introduced with 3bd1642d ("imx: fix USB boot mode detection for i.MX 6UL and 6ULL") Fixes: 3bd1642d ("imx: fix USB boot mode detection for i.MX 6UL and 6ULL") Signed-off-by: NStefan Agner <stefan.agner@toradex.com> Reviewed-by: NStefano Babic <sbabic@denx.de> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Chris Packham 提交于
U-boots spi-nor support is currently considered a work in progress. For now to avoid issues it is necessary to add a "spi-flash" compatible string. Eventually the "jedec,spi-nor" will be sufficient when the core U-boot code is updated to support it. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NJagan Teki <jagan@openedev.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Masahiro Yamada 提交于
Now the entry to the NAND driver init can be is controlled by DT; it should not hurt to compile the driver all the time. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The system bus is not enabled by default for NAND, eMMC boot etc. of PXs3. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
This imply was added when the option was moved by the moveconfig tool, but the intention is not clear. Move it to defconfig. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Support PXs3 SoC and its reference development board. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Import updates queued up for Linux 4.14-rc1. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
LD20 has SD ctrl instead of MIO ctrl. LD11 has both of them. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Support system clocks for LD4, Pro4, sLD8, Pro5, PXs2/LD6b, LD11, LD20. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Dai Okamura 提交于
Signed-off-by: NDai Okamura <okamura.dai@socionext.com> Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
This is now set up by the pinctrl driver when the NAND driver is probed. Remove the legacy code. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Migrate to the DT-based NAND init entry. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the NAND initialization process is driven by the driver itself. CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The new SoC PXs3 changed the address of PLL, but still uses the same PLL name. We can not define SC_*PLLCTRL in the common header. Move them to per-SoC .c file. Also, fix some PLL comments. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The #include <common.h> was added for mdelay(). Later, the declaration of mdelay was moved to <linux/delay.h> by commit 5bc516ed ("delay: collect {m, n, u}delay declarations to include/linux/delay.h"). There is no need to include <common.h> now. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
A patch for NAND uclass support was proposed about half a year ago: https://patchwork.ozlabs.org/patch/722282/ It was not merged and I do not see on-going work for this. Without DM-based probing, we need to set up pinctrl etc. in an ad-hoc way and give lots of crappy CONFIG options for base addresses and properties, which are supposed to be specified by DT. This is painful. This commit just provides a probe hook to retrieve "reg" from DT and allocate private data in a DM manner. This DT driver is not essentially a NAND driver, in fact it is (ab)using UCLASS_MISC. Once UCLASS_NAND is supported, it would be possible to migrate to it. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
- 29 8月, 2017 1 次提交
-
-
由 Masahiro Yamada 提交于
Linux supports platform_get_resource_byname() to look up a resource by name. We want a similar helper. It is useful when a device node has named register regions. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-