- 11 1月, 2011 6 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
The register information of SCIF/SCI was compiled by drivers/serial/serial_sh.h. Therefore, these are not necessary. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds support for the SHMIN SH7706 board(T-SH7706LAN). The CPU of this board is SH7706. There are SDRAM of 32M byte, Flash memory of 512K byte, Serial, 10Base Ether and MMC. http://web.kyoto-inet.or.jp/people/takagaki/T-SH7706/T-SH7706.htmSigned-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
I copied the setting of CPU from Linux kernel and commonized it. By this, we can communalize a kernel and information. And added the serial setting of many CPU's. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Setarcos 提交于
The eth_device.name field length is limited by NAMESIZE, which is 16 defined in include/net.h. Unfortunately, two of the names in lan91c96.c are beyond that. Signed-off-by: YanJun Yang <yangyj.ee@gmail.com>
-
- 10 1月, 2011 13 次提交
-
-
由 Macpaul Lin 提交于
Add Faraday's ftgmac100 (gigabit ethernet) MAC controller's driver. Signed-off-by: NMacpaul Lin <macpaul@andestech.com>
-
由 Mike Frysinger 提交于
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Some ports set up the board info structure at the same time as the global data structure, and largely keep them together. So generate a define for the board info struct too. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
The include/miiphy.h header duplicates a lot of things from linux/mii.h. So punt all the things that overlap to keep the API simple and to make merging between U-Boot and Linux simpler. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
The flash_verbose logic is only used by the CFI MTD layer, so if we aren't using that, disable the logic completely. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
These strings are only read, so no need to have them be writable. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
These "last" variables aren't used outside of this file, so add static. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Rather than keep the load_addr definition with the bootm code (which just happens to use this), move it to the common env code. This way we can disable bootm support completely while retaining load_addr usage with many other commands. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
We have config_defaults.h which are random configuration settings that everyone gets by default. We also have config_cmd_default.h which is a recommended list of defaults but boards have to opt into. Now we have config_cmd_defaults.h which is a list of defaults that everyone gets and has to actively opt out of. For now, we populate it with the bootm command which previously was unable to be disabled. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Mike Frysinger 提交于
Currently, only basic completion is supported (no globs), but this is what we had previously. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Wolfgang Denk 提交于
Commit 98e69567 "mpc52xx: add support for tqm52xx based board charon" caused build warnings on some systems. Fix these. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
-
由 Mike Frysinger 提交于
One more place that was missed during the do_reset() unification. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 24 12月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
Commit 722b061b "autocomplete: remove runtime handler install" caused some boards (like NETTA2_V2) to break with errors like these: cmd_net.c:296: error: expected expression before ',' token Fix this. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org>
-
- 23 12月, 2010 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 21 12月, 2010 1 次提交
-
-
由 John Rigby 提交于
It can be optimised out by the compiler otherwise resulting in obscure errors like a board not booting. This has been documented in README since 2006 when these were first fixed up for GCC 4.x. Signed-off-by: NJohn Rigby <john.rigby@linaro.org> Fix some additional places. Signed-off-by: NWolfgang Denk <wd@denx.de> Acked-By: NAlbert ARIBAUD <albert.aribaud@free.fr>
-
- 19 12月, 2010 9 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Dirk Behme 提交于
Convert the variable omap3_evm_version to u32 to work around some broken linkers from older tool chains. E.g. CodeSourcery's 2009q1-203 ld 2.19.51.20090205. Without this, these linkers stop linking 'omap3_evm' or at least issue a warning. Like arm-none-linux-gnueabi-ld: section .bss [8003f5e0 -> 8007e337] overlaps section .rel.dyn [8003f5e0 -> 80044e57] arm-none-linux-gnueabi-ld: section .dynsym [80044e58 -> 80044ef7] overlaps section.bss [8003f5e0 -> 8007e337] arm-none-linux-gnueabi-ld: u-boot: section .bss vma 0x8003f5e0 overlaps previous sections CC: Sanjeev Premi <premi@ti.com> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Li Yang 提交于
The current code use all the voltage range support by the host controller to do the validation. This will cause problem when the host supports Low Voltage Range. Change the validation voltage to be based on board setup. Signed-off-by: NLi Yang <leoli@freescale.com> Tested-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Jerry Huang 提交于
The max clock of MMC is 52MHz Signed-off-by: NJerry Huang <Changm-Ming.Huang@freescale.com> Tested-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Jerry Huang 提交于
After booting the u-boot, and first using some SD card (such as Sandisk 2G SD card), because the field 'clock' of struct mmc is zero, this will cause the read transfer is always active and SDHC DATA line is always active, therefore, driver can't handle the next command. Therefore, we use mmc_set_clock to setup both the data structure and HW to the initial clock speed of 400000Hz. Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com> Tested-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Matthew McClintock 提交于
Add reginfo as a default command for p1022ds boards Signed-off-by: NMatthew McClintock <msm@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Li Yang 提交于
The current code use all the voltage range support by the host controller to do the validation. This will cause problem when the host supports Low Voltage Range. Change the validation voltage to be based on board setup. Signed-off-by: NLi Yang <leoli@freescale.com> Tested-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Jerry Huang 提交于
The max clock of MMC is 52MHz Signed-off-by: NJerry Huang <Changm-Ming.Huang@freescale.com> Tested-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Jerry Huang 提交于
After booting the u-boot, and first using some SD card (such as Sandisk 2G SD card), because the field 'clock' of struct mmc is zero, this will cause the read transfer is always active and SDHC DATA line is always active, therefore, driver can't handle the next command. Therefore, we use mmc_set_clock to setup both the data structure and HW to the initial clock speed of 400000Hz. Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com> Tested-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 18 12月, 2010 8 次提交
-
-
由 Florian Fainelli 提交于
This command is used to read the device ONFI parameters page. Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
-
由 Lei Wen 提交于
Yaffs image require to use the oob to store some info, so when we burn the yaffs image, we need to also write the image's oob part into flash. This patch add addition suffix to onenand write to give the uboot the power to directly burn the yaffs image to onenand. Signed-off-by: NLei Wen <leiwen@marvell.com>
-
由 Reinhard Meyer 提交于
This is part of the timer cleanup effort. In the future we only use get_timer() in its intended way to program timeout loops. reset_timer() shall not be used anymore. Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>
-
由 Mike Frysinger 提交于
These id tables need not be writable. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Stefano Babic 提交于
Fix clock divider for COM57H5M10XRC display. The previous setting caused flicker. Tested on Qong (EVBLite with COM57H5M10XRC). Signed-off-by: NStefano Babic <sbabic@denx.de> Acked-by: NWolfgang Denk <wd@denx.de> Acked-by: NAnatolij Gustschin <agust@denx.de>
-
由 Mike Frysinger 提交于
Multiple rules are using the expanded AFLAGS/CFLAGS settings and some are getting so long that the rules need to be line wrapped. So unify them in one variable, use that variable in the rule, and then unwrap things. This makes the actual `make` output nicer as it doesn't have line continuations in it anymore. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Timur Tabi 提交于
In some usages of inline assembly, hard-coded registers were specified when a scratch register should have been used instead. Signed-off-by: NTimur Tabi <timur@freescale.com>
-
由 Mike Frysinger 提交于
The non-reentrant versions of the hashtable functions operate on a single shared hashtable. So if two different people try using these funcs for two different purposes, they'll cause problems for the other. Avoid this by converting all existing hashtable consumers over to the reentrant versions and then punting the non-reentrant ones. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-