This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: NTom Rini <trini@konsulko.com>

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: NTom Rini <trini@konsulko.com>

Boards using link-local need lib rand.

When link-local is moved to Kconfig, this dependency will be described
there.
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>

This command needs to exist in the Kconfig so that it can be moved from
the config_cmd_default.h.
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>

The help for this was simply copied from another command.

Update it to reflect the command.
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>

This config needs to be available in the Kconfig to allow it to be
removed from arch defaults.
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>

Patch 33fe2fb8 titled
"mmc: bcm283x: Remove get_timer_us() from mmc driver"
incorrectly replaced ad-hoc get_timer_us() function
with a plain get_timer(). The get_timer() operates in
mSec units instead of uSec though, which caused very
slow operation of the driver.

Restore the original behavior of the driver, but avoid
get_timer_us() and use timer_get_us() instead. The later
is part of the standard API.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Jakub Kiciński <moorray3@wp.pl>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: NJakub Kicinski <kubakici@wp.pl>

Update new naming scheme.
Signed-off-by: NSamuel Egli <samuel.egli@siemens.com>
Acked-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.
Signed-off-by: NSamuel Egli <samuel.egli@siemens.com>
Acked-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

Unlike most configuration options defining this actually disables
support for a feature (parallel flash). Eventually the logic behind this
should probably be flipped so that '#ifndef CONFIG_SYS_NO_FLASH' becomes
'#ifdef CONFIG_HAS_PARALLEL_FLASH' but for now lets document the
existing behaviour.
Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NStefan Roese <sr@denx.de>

BeagleBoard-X15 uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon).  Prior silicon is OK using this address as well.
Signed-off-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

DRA7/AM57xx devices can be operated in many different configurations.
When the SoC is supposed to support a configuration where low power mode
state may involve the SoC completely powered off and DDR is in self
refresh, SoC EMIF controller should not be the master of the reset
signal and an external entity might be in control of things.

The default configuration of Linux on TI evms involve not powering off
the voltage rails (due to various reasons including reliability concerns)
and must not allow DDR reset to be controlled by EMIF. On platforms
where external entity might control the reset signal, this configuration
will be a "dont care".

Fixes: 536d8747 ("ARM: DRA7: Update DDR IO registers")
Tested-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NBrad Griffis <bgriffis@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

ti: omap4: remove CONFIG_SPL_EXT_SUPPORT from ti_omap4_common.h since it is now in ti_armv7_common.h
Signed-off-by: NGuillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Tested on Pandaboard (rev. A3) and Beagleboard xM (rev. B).
Compilation tested on TI armv7 boards and OMAP boards from other vendors.
Signed-off-by: NGuillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

updates for the siemens am335x based boards:

- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
  to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
  Leds can now be defined in Environment
- add generic env based dfu button
  Which gpio is used for the dfu button can be defined
  through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3
Signed-off-by: NSamuel Egli <samuel.egli@siemens.com>
Acked-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>

This introduces the part start and part size sub-commands. The purpose of these
is to store the start block and size of a partition in a variable, given the
device and partition number.

This allows reading raw data that fits a single partition more easily.
For instance, this could be used to figure out the start block and size of a
kernel partition when a partition table is present, given the partition number.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Acked-by: NStephen Warren <swarren@nvidia.com>
[trini: Change "%lx" to LBAF]
Signed-off-by: NTom Rini <trini@konsulko.com>

This fixes a misaligned declaration.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

The get_max_arm_speed() and get_max_dev_speed() used wrong register
fields to get the maximum speeds. This commit fixes the bug.
Signed-off-by: NVitaly Andrianov <vitalya@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

When we're polling and thus handling key-repeat in software, make sure
to disable idle reports, some keyboards may have these enabled by default
messing up our software keyrepeat.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Without this we loose every other interrupt packet. We never noticed this
because with keyboards the packets which we were loosing would normally
be key release packets.

But now that we do keyrepeat in software instead of relying on the hid
idle functionality, missing a release will result in key repeat triggering.

This commit fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

There is no harm in declaring the function prototypes even if nothing
implements them, and when CONFIG_DM_USB=y the various usb functions are
available regardless of any controller drivers being enabled.

This fixes compile warnings due to missing prototypes on ARCHs where
the ARCH Kconfig always enables CONFIG_DM_USB and various usb drivers.

One could argue that in the case of no controllers CONFIG_DM_USB should not
be set, but this problem is typically seen during bringup of boards which
do actually have usb controllers.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

With the change to make sure that CONFIG_CMD_NET is enabled this board
no longer fits into the linker script:

powerpc-linux-ld.bfd: section .resetvec loaded at [fffffffc,ffffffff] overlaps section .u_boot_list loaded at [ffffff58,00000723]
powerpc-linux-ld.bfd: u-boot: section .resetvec lma 0xfffffffc adjusted to 0x724
powerpc-linux-ld.bfd: u-boot: section `.resetvec' can't be allocated in segment 0
LOAD: .data.init .text .rodata .reloc .data .u_boot_list .resetvec
powerpc-linux-ld.bfd: final link failed: File truncated

Drop CONFIG_SYS_LONGHELP to free up space.

Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

This allows using only one of either raw or fs mode for SPL mmc boot, without
the need to have provisions for the other. In particular, a device may have
U-Boot installed on a file system on the mmc, without ever needing to read
U-Boot from raw memory. Thus, there is no reason to provide a sector or
partition for raw mode. This allows this behaviour and still provides a robust
fallback mechanism in case provisions for both modes are defined.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

This switches some printf calls to puts and avoids a test repetition.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

When building tools-only (or env) we need to be sure that we do use
<linux/kconfig.h> and do not use <generated/autoconf.h>.  This will fix
problems such as running 'make defconfig' or 'make sandbox_config' and
then 'make tools-only'.

Based on the responses below to the thread add linux/kconfig.h higher in
the includes and drop the now unneeded autoconf.h lower down to ensure
the default environment is included correctly

http://lists.denx.de/pipermail/u-boot/2015-June/216849.htmlSigned-off-by: NPeter Robinson <pbrobinson@gmail.com>

This fix is necessary to avoid booting the default ITB configuration.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>

We want to see if the requested start or total block count are
unaligned.  We discard the whole numbers and only care about the
remainder.  Update the code to use div_u64_rem here and add a comment.

Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Reported-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Rini <trini@konsulko.com>
Tested-by: NBernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

since we have now various processor-speeds it isn't useful anymore to
preinitialize kernels-delay loop.

Rather we want the kernel to calibrate it on every boot.
This wastes around 80ms boottime but is compatible to all CPU-speeds.
Signed-off-by: NHannes Schmelzer <oe5hpm@oevsv.at>

in future we support yet another b&r am335x based board, where Timer 5 is
wired to backlight-driver.

So we introduce a new driver-type '2' to setup timer5 instead timer6.
Signed-off-by: NHannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Currently there is no default value for NETARGS if CONFIG_CMD_NET=y isn't set.
This results in build errors which was first discovered when trying to run
make env.

By defining a blank NETARGS these errors can be avoided.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Tested-by: NMaxin B. John <maxin.john@enea.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Since the tam3517 base board has a 16bit wide nand connected to
the gpmc, enable the prefetch mode, since that is now supported.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: pekon gupta <pekon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: NTom Rini <trini@konsulko.com>

commit c316f577 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: NTom Rini <trini@konsulko.com>

The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: NTom Rini <trini@konsulko.com>

The MSI Primo 81 is an Allwinner A31s-based tablet on which the
OTG port is the only accessible USB interface.  The existing
defconfig had VGA console on the LCD enabled, but was missing
keyboard support because the prerequisites for that (sunxi MUSB
support and AXP221 GPIO support) had not been available before.
All previously missing dependencies are available now, so this
patch enables keyboard support and its prerequisites in the
defconfig.
Signed-off-by: NKarsten Merker <merker@debian.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.

This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

Remove the unused sunxi_musb_exit method, there is no code in u-boot
calling the exit method, and our implementation was broken as it did
not disable the clocks and asserted reset.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>