This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
and set it default to 0.
Signed-off-by: NVipul Kumar <vipulk@xilinx.com>
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch enabled CONFIG_SYS_I2C_ZYNQ in the respective
defconfig.
Signed-off-by: NVipul Kumar <vipulk@xilinx.com>
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ.
Signed-off-by: NVipul Kumar <vipulk@xilinx.com>
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the
values over to the defconfigs.
Signed-off-by: NVipul Kumar <vipulk@xilinx.com>
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>

This patch added Kconfig support for FPGA_SPARTAN3 and migrates the
values over to the defconfigs.
Signed-off-by: NVipul Kumar <vipulk@xilinx.com>
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>

Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NArno Steffens <star@gmx.li>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Fix commit f1bcad22 ("net: e1000: add support for writing to
EEPROM").
Signed-off-by: NBernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

After commit ba1f9667 ("net: designware: add clock support")
we got NET broken on axs101 and axs103 platforms.

Some clock don't support gating so their clock drivers don't
implement .enable/.disable callbacks. In such case clk_enable
returns -ENOSYS.
Also some clock drivers implement .enable/.disable callbacks not for all
clock IDs and return -ENOSYS (or -ENOTSUPP) for others.

If we have such clock in 'clocks' list of designware ethernet controller
node we fail to probe designware ethernet.

Fix it.
Signed-off-by: NEugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Fix some style violations in the generic PHY management code.
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Fix some style violations in the MDIO command.
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Commit 68e6ecad ("net: phy: marvell 88e151x: Fix handling of RGMII
interface types") fixed the initialization of 88e151x phys, but made it
so that interfaces of type PHY_INTERFACE_MODE_RGMII had both RX and TX
delay bits cleared. The default (like in m88e1111s_config) is to have
both bits set.

Hence, this patch changes the behavior in the PHY_INTERFACE_MODE_RGMII
case so that both bits are set.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Fix some style violations (mostly wrong indentions) in the Marvell PHY
driver.
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Make the tsec ethernet driver compatible with a live device tree.
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NMario Six <mario.six@gdsys.cc>

tsec_initialize allocates a private driver structure using malloc.
Should the memory allocation of this private structure fail, the
function execution is aborted with a return 0, but the previously
allocated device structure is never freed, hence leaked.

Free the device structure in the error case.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Signed-off-by: NMario Six <mario.six@gdsys.cc>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

mmc_of_parse() doesn't set a default value if none is available in DT.
In that case, use a default 52MHz clock rate.
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

This reduces the size of the binary by about 196 bytes.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.

This saves around 740 bytes for the am335x_evm SPL.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig.  We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use.  We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig.  In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files.  The previous default
only applied in some cases, even on a specific SoC family.
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NAlex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Commit d695d662 ("spl: eMMC/SD: Provide one __weak spl_boot_mode()
function") breaks the boot on several i.MX6 boards,
such as cuboxi and wandboard:

U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 +1300)
Trying to boot from MMC1
Failed to mount ext2 filesystem...
spl_load_image_ext: ext4fs mount err - 0

Partially revert it so that we can boot U-Boot again on these
i.MX6 platforms.
Reported-by: NJonathan Gray <jsg@jsg.id.au>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Tested-by: NBreno Lima <breno.lima@nxp.com>

The device-tree node for the PMU clk controller assigns to its parent
(i.e. PLL_PPLL) even though this clock currently is set up statically
by an init-function.

In order to avoid unexpected failures, a simple implementation of
set_rate (which accepts requests, but notifies the caller of the
preset frequency in its return value) and get_rate (which always
returns the preset frequency) are added.

Note that this is required for the RK808 PMIC to probe successfully on
the RK3399-Q7, following the support for the assigned-clocks property.

References: commit f4fcba5c ("clk: implement clk_set_defaults()")
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: NKlaus Goger <klaus.goger@theobroma-systems.com>

TPL offset 0xff704004 is unaligned address which is adding nearest
8-bytes for next instruction, So  0xff704004 is adding 0x20 for
proper alignment which is causing the next instruction data
0xefffffff is moved.

Hexdump with overlaped bytes:
-----------------------------
0000000 0000 0000 0000 0000 0000 0000 0000 0000
0000010 0000 0000 0000 0000 0000 0000 ffff eaff

So, Fix the TEXT_BASE for proper aligned address 0xff704000
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Due to size limitations in SPL by adding falcon mode,
rk3288 support TPL. In order to not overlap SPL_TEXT_BASE
add TPL_TEXT_BASE with u-boot-tpl.lds that intern call
u-boot-spl.lds with proper TEXT_BASE values.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Since commit ba1f9667 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3368 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.

This change extends the RK3368 clk driver to:
(a) provide a enable op
(b) signals success to the caller when the clocks for the GMAC are
    enabled (no actual action is necessary as the gates are open
    after reset)

References: commit ba1f9667 ("net: designware: add clock support")
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: NKlaus Goger <klaus.goger@theobroma-systems.com>

Since commit ba1f9667 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3399 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.

This change extends the enable-op of the rk3399 clk driver to signal
success to the caller when the clocks for the GMAC are enabled.

References: commit ba1f9667 ("net: designware: add clock support")
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: NKlaus Goger <klaus.goger@theobroma-systems.com>

usdhc4 has eMMC on icore-rqs boards, SPL is not detecting
it becuase of u-boot,dm-spl flag so add it to make eMMC working.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Tidy up CONFIG_SYS_BOOTCOUNT_SINGLEWORD from the whitelist as there's
no remaining uses of it left.
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>

Convert CONFIG_BOOTCOUNT_ALEN to Kconfig
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>

Make generate boot counter selected in the same way as other boot count
drivers
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>

Integrate Boot counter for Atmel AT91SAM9XE into Kconfig
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_EXT
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_I2C
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_RAM
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>

This converts the following to Kconfig:
  CONFIG_BOOTCOUNT_ENV
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>