Add CMD_GPIO to Kconfig and run tools/moveconfig.py .
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NStefano Babic <sbabic@denx.de>

BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).

Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728

The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.

Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.

NOTE: Commit eae7ae18 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.

As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: NSteve Kipisz <s-kipisz2@ti.com>
Signed-off-by: NSchuyler Patton <spatton@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Acked-by: NLokesh Vutla <lokeshvutla@ti.com>

These options were already defined in mv-common.h file.
Signed-off-by: NLuka Perkov <luka.perkov@sartura.hr>

It is already defined in included mv-common.h file.
Signed-off-by: NLuka Perkov <luka.perkov@sartura.hr>

Signed-off-by: NLuka Perkov <luka.perkov@sartura.hr>

The CONFIG_CMD_ENV is enabled by default so we can safely remove it.
Signed-off-by: NLuka Perkov <luka.perkov@sartura.hr>

Avoid double typing in the shell and build u-boot.kwb when running "make" only.
Signed-off-by: NLuka Perkov <luka.perkov@sartura.hr>

Mainline kernel for this device has only support for device tree. We can safely
drop this legacy code.
Signed-off-by: NLuka Perkov <luka.perkov@sartura.hr>

Create include/configs/mv-plug-common.h for common definitions
for Sheevaplug, Guruplug and Dreamplug. This will make it easier
to ensure the built u-boots stay in track with each other
Signed-off-by: NQuentin Armitage <quentin@armitage.org.uk>

CONFIG_DISPLAY_CPUINFO is already defined in mv-common.h
Signed-off-by: NQuentin Armitage <quentin@armitage.org.uk>

Cosmetic: CONFIG_OF_LIBFDT was in a different position in the config
file for the Dreamplug, compared to the Sheevaplug and Guruplug.
Signed-off-by: NQuentin Armitage <quentin@armitage.org.uk>

include/configs/mv-common.h brings in the required filesystems if
CONFIG_SYS_MVFS is defined, so use it for Sheevaplug and Guruplug.
Signed-off-by: NQuentin Armitage <quentin@armitage.org.uk>

For Marvell plugs, move the configuration of DHCP, NAND/SF, PING
and USB commands, and HUSH_PARSER into the _defconfig file, rather
than the include/configs/*plug.h files.

This avoids compiler warnings of duplicate definitions if the
option is selected in the .config, but also defined in the
include/configs/*plug.h file.
Signed-off-by: NQuentin Armitage <quentin@armitage.org.uk>

include/configs/guruplug.h defined CONFIG_CMD_FAT twice.
Signed-off-by: NQuentin Armitage <quentin@armitage.org.uk>

The Marvell plugs are very similar systems, and so it makes sense
for their u-boots to have the same commands/configuration.

Add EXT4 and MII to Dreamplug, DATE to Guruplug and Sheevaplug.
Add CONFIG_SYS_ALT_MEMTEST to Sheevaplug.
There are still command differences around NAND, SPI/NOR.

Also default to building u-boot.kwb for Sheevaplug and Guruplug.
Signed-off-by: NQuentin Armitage <quentin@armitage.org.uk>

With this change Synopsys DesignWare SDP board is switched to driver
model for both serial port (serial_dw) and Ethernet (Designware GMAC).

This simplifies include/configs/axs101.h and allows for reuse of Linux's
Device Tree description.

For simplicity Linux's .dts files are not blindly copied but only very
few extracts of them are really used (those that are supported in U-Boot
at the moment).
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

CONFIG_SYS_EARLY_PCI_INIT is not needed any more since with driver
model, PCI enumeration is automatically triggered.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

These are leftover when converted to use driver model pci.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Move to driver model for pci on QEMU.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Move chipset-specific codes such as PAM init, PCIe ECAM and MP table
from pci.c to qemu.c, to prepare for DM PCI conversion.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Add Kconfig options for 8259 and 8254.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Rename pcat_timer.c to i8254.c and pcat_interrupts.c to i8259.c,
to match their header file names (i8254.h and i8259.h).
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

CONFIG_SYS_NUM_IRQS is actually not something we can configure,
but an architecture defined number of ISA IRQs. Move it from
x86-common.h to asm/interrupt.h and rename it to SYS_NUM_IRQS.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

wandboard and mx6cuboxi have warnings because BOOT_DELAY
is defined twice.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Vagrant Cascadian <vagrant@debian.org>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>

Add an initr function in the board_r.c file for the AMBA Plug&Play
command. Add a Kconfig entry for the ambapp command and remove all
CONFIG_CMD_AMBAPP defines from the board configuration headers.

Add a Kconfig entry to display the AMBA Plug&Play information
on startup. This option is off by default. Remove relevent define
from board configuration headers.
Signed-off-by: NFrancois Retief <fgretief@spaceteq.co.za>

Update the GRSIM board with the memory settings for the evaluation
version of TSIM. This free version of TSIM is used for testing.
Signed-off-by: NFrancois Retief <fgretief@spaceteq.co.za>

Update the LEON2/3 serial driver to make use of the readl and writel
macros as well as the WATCHDOG_RESET() macro.

Add readl/writel and friends to the asm/io.h file.

Introduce the gd->arch.uart variable to store register address.

Lastly, remove baudrate scaler macro variables from board config. It
is now calculated in the serial driver using the global data variable.
Signed-off-by: NFrancois Retief <fgretief@spaceteq.co.za>

This adds support to update firmware on qspi flash present on
am437x-sk-evm and am43xx-epos-evm via DFU.

On device:
=> setenv dfu_alt_info ${dfu_alt_info_qspi}
=> dfu 0 sf 0:0

On host:
$ sudo dfu-util -l
$ sudo dfu-util -D u-boot.bin -a u-boot.bin
Signed-off-by: NVignesh R <vigneshr@ti.com>

-> Add National instrument ethernet transceiver configuration used (DP83848)
-> Change cpsw slave phy address
-> modify nand configuration to use the correct ECC and correct nand features

CONFIG_BOOTDELAY is defined in config_distro_defaults.h
Signed-off-by: NMatwey V. Kornilov <matwey.kornilov@gmail.com>
[trini: Drop omap3_logic.h settings which were a warning and no longer
        correct usage].
Signed-off-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>

hrcon DH(dual head) has two video outputs per FPGA.
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>

The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.

On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: NTom Rini <trini@konsulko.com>

hrcon has no CH7301 DVI-transmitter.
Probably not removed when copying from iocon.
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>

Support dlvision-10g hardware with displayport output.
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>

Since we don't have for sure a valid IP-setup during
board_late_init(...) because it maybe allready stored in environment or
not, we cannot form a proper vxWorks bootline at this place.

So we move to the way, forming the bootline just before
executing/launching vxWorks. To do this we use the bootvx command
instead go.

We only have to form the "othbootargs" environment variable, the rest is
done pretty good by the "bootvx" commannd.
Signed-off-by: NHannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Support LCDIF for mx7dsabresd board:
1. Add pinmux settings
2. Add VIDEO related macro definition and videomode env settings.
Signed-off-by: NPeng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>

Support lcdif display:
1. Add pinmux and pad settings for LCDIF
2. Introduce setup_lcd to do the settings for LCDIF
3. Enable VIDEO related macros in board header files
4. Add a new env videomode which is needed by mxsfb.c. The
   settings for videomode in this patch is for TFT43AB.
5. Tested on mx6ul 14x14/9x9 evk.
Signed-off-by: NPeng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>