Add local size_t variable to crypto_comp_decompress as intermediate
storage for destination length to avoid memory corruption and incorrect
results on 64 bit targets.

This is what linux does for the various lz compression implementations.
Signed-off-by: NPaul Davey <paul.davey@alliedtelesis.co.nz>
Cc: Heiko Schocher <hs@denx.de>
Tested-by: NHeiko Schocher <hs@denx.de>

Fix coverity issues for i.MX8

The new board version has the 2nd FPGA connected via CS# 0 instead of
2 on SPI bus 1. Change this setup in the DT accordingly. Please note
that this change does still work on the old board version because the
CS signal is not used on this board.
Signed-off-by: NStefan Roese <sr@denx.de>

Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the theadorable Armada-XP board.
Signed-off-by: NStefan Roese <sr@denx.de>

With patch 49b23e03 (pci: mvebu: Increase size of PCIe default mapping)
the mapping size for each PCI(e) controller was increased from 32MiB to
128MiB. This leads to problems on boards with multiple PCIe slots / ports
which are unable to map all PCIe ports, e.g. the Armada-XP theadorable:

DRAM:  2 GiB (667 MHz, 64-bit, ECC not enabled)
SF: Detected m25p128 with page size 256 Bytes, erase size 256 KiB, total 16 MiB
Cannot add window '4:f8', conflicts with another window
PCIe unable to add mbus window for mem at f0000000+08000000
Model: Marvell Armada XP theadorable

This patch moves the base address for the PCI(e) memory spaces from
0xe8000000 to the end of SDRAM (clipped to a max of 0xc0000000 right now).
This gives move room and flexibility for PCI(e) mappings.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: VlaoMao <vlaomao@gmail.com>
Tested-by: VlaoMao <vlaomao at gmail.com>

Add NXP linux team upstream maillist as reviewer
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Commit 3c28576b ("arm: dts: imx8qxp: fix build warining")
fixed the dts warning by removing the unnecessary
#address-cells/#size-cells, but the recommendation for regulators is not
to place them under "simple-bus", so move the reg_usdhc2_vmmc regulator
accordingly.
Signed-off-by: NFabio Estevam <festevam@gmail.com>

board/freescale/mx8mq_evk/README has been introduced by mistake
in commit d0dd7397 ("imx: add i.MX8QXP MEK board support")

Remove it for now as this should be introduced when mx8mq_evk
support is in place.
Reported-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

If there is no CONTAINER entry, there is no need to flatten container
header.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Fix:
CID 184233:    (NEGATIVE_RETURNS)
Using variable "container" as an index to array "imx_header.fhdr".

Reported-by: Coverity
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Fix:
CID 184234:    (TAINTED_SCALAR)
Using tainted variable "header.num_images - 1" as an index into an array "header.img".

Reported-by: Coverity
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Check lseek return value.

Fix Coverity CID: 184236 184235 184232

Reported-by: Coverity
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

New ACPI assembler issues a warning:

board/intel/edison/dsdt.asl.tmp     13:     Offset (0x00),
Remark   2158 -                                       ^ Unnecessary/redundant use of Offset operator

Indeed, in the OperationRegion the offset is 0x00 by default.

Thus, drop unneeded Offset() use as suggested by ACPI assembler.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

- replace the dynamic size of the relocation table
  with a fixed but configurable size
- fixes non-working CONFIG_OF_SEPARATE=y due to invalid _end symbol

Currently the size of the relocation table will be shrunk
to the actual size needed. Although this gives a maximal
space saving, it messes up the _end symbol. This breaks
features like appended DTBs because the _end symbol doesn't
point to the real end of the U-Boot binary.

Remove the size shrinking and make the size of the relocation
table fixed but configurable. This follows the Linux approach
and the user can adjust the size to his needs.

Also rename the relocation table section from .rel to .data.reloc
to follow the Linux approach and to avoid ambiguities with the
.rel.* sections added by the linker.
Reported-by: NLars Povlsen <lars.povlsen@microsemi.com>
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>

It is perfectly fine to write th DTCNTL TAP count and enable the
SCC sampling clock operation in the same write.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

When the bus switches to 1.8V mode of operation, it is necessary to
verify that the card correctly initiated and completed the voltage
switch. This is done by reading out the state of DATA0 line.

This patch implement support for reading out the state of the DATA0
line, so the MMC core code can correctly switch to 1.8V mode.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

Make sure to clear HS400 configuration when resetting the SCC block.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

Add check to avoid touching the SCC tuning registers in case the IP
doesn't support them or if the support isn't in place yet.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

Preinitialize the SD card signals regulator to 3.3V, which is the
default post-reset setting, to be sure the regulator is set to a
valid value.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

Configure the clock settings before reconfiguring any other IO settings.
This is required when the clock must be stopped before changing eg. the
pin configuration or any of the other properties of the bus. Running the
clock configuration first allows the MMC core to do just that.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

In case the controller performs card tuning, that is, sends MMC
command 19 or 21, silence possible CRC error warning prints. The
warnings are bound to happen, since the tuning will fail for some
settings while searching for the optimal configuration of the bus
and that is perfectly OK.

This patch passes around the MMC command structure and adds check
into tmio_sd_check_error() to avoid printing CRC error warning
when the tuning happens.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

Properly handle return values and abort operations when they are
non-zero. This is a minor improvement, which fixes two remaining
unchecked return values.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

The SD UHS SDR12, SDR25, SDR50, SDR104, DDR50 and MMC HS200, HS400
modes all use 1.8V signaling, while all the legacy modes use 3.3V
signaling. While there are extra modes which use 1.2V signaling,
the existing hardware does not support those.

Simplify the pinmux such that 3.3V signaling implies legacy mode
pinmux and the rest implies UHS mode pinmux. This prevents the
massive case statement from growing further. Moreover, it fixes
an edge case where during SD 1.8V switch, the bus mode is still
set to default while the signaling is already set to 1.8V, which
results in an attempt to communicate with a 1.8V card using pins
in 3.3V mode and thus communication failure.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

Patch "ARM: rmobile: Mark 4-64GiB as DRAM on Gen3" marked the entire
64bit DRAM space as cachable. On CortexA57, this might result in odd
side effects, where the CPU tries to prefetch from those areas and if
there is no DRAM backing them, CPU bus hang can happen.

This patch fixes it by generating the mem_map structure based on the
actual memory layout obtained from the DT, thus not marking areas
without any DRAM behind them as cachable.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Fixes: c1ec3476 ("ARM: rmobile: Mark 4-64GiB as DRAM on Gen3")
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add definition of the POCCTRL register and bits therein to R8A77990 E3
pincontrol driver. This allows the pincontrol driver to configure SDHI
pin voltage according to power-source DT property.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Use fixed 4bit size for generating the DRV register element mask,
not the size of the value, which can be smaller.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Just 2 non-functinal changes:

 1. Rename of EMDK to EMSDP so it matches real marketing name
 2. Add essential README for IoTDK

Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>

Real marketing name of the board was recently updated so
to accommodate that change renaming the board and all
related to it.
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>

This part should've been remove in commit 88d60db0 ("arm: ti: boot:
Remove environment partition"), but I missed it somehow. Remove reading
dtb file from environment partition on eMMC, as we don't have it
anymore.
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

Fixes possible resource leak in dm_test_tee() reported by Coverity.

Reported-by: Coverity (CID: 184175)
Signed-off-by: NJens Wiklander <jens.wiklander@linaro.org>

This line is no more needed and can be removed.

Only CONFIG_CMD_SOURCE is defined in Kconfig and
used in defconfig files.

CONFIG_SOURCE if not defined in source code and
"config SOURCE" is not present in any Kconfig.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

The Makefile already tests for SPL_DM_REGULATOR_GPIO, but Kconfig
does not provide it. This adds SPL_DM_REGULATOR_GPIO to Kconfig.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Currently the base is 3 fix it 10 so that IDs follow decimal system.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvulta@ti.com>

On our demo setup for SD card boot, the u-boot environment
is in a FAT partition.

This patch changes the default configuration, specifing that
the u-boot environment is in a FAT partition instead of raw MMC.
Signed-off-by: NAndrei Stefanescu <andrei.stefanescu@microchip.com>
Acked-by: NEugen Hristev <eugen.hristev@microchip.com>

The default bootcommand needs to be accurate w.r.t the nand memory map
at http://www.at91.com/linux4sam/bin/view/Linux4SAM/AT91sam9x5ekMainPage#NAND_Flash_demo_Memory_map

Updated to load kernel + dtb at right offsets and boot the zImage.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>