This converts the following to Kconfig:
   CONFIG_CMD_EECONFIG
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_ECCTEST
Signed-off-by: NSimon Glass <sjg@chromium.org>

This subsystem has not been converted to driver model, there is only one
driver and only one board that uses it. Drop it and its CONFIG option.

Also drop the rtc4543 RTC driver since it uses TWS.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_DS4510
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>

Commit 94e3c8c4 ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it.  Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool.  In many cases we can select
these because they are required to implement other drivers.  We also
correct how we include the various hashing algorithms in SPL.

This commit was generated as follows (after Kconfig additions):

[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL

Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.

Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

We rename CONFIG_FIT_DISABLE_SHA256 to CONFIG_FIT_ENABLE_SHA256_SUPPORT which
is enabled by default and now a positive option.  Convert the handful of boards
that were disabling it before to save space.

Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: NTom Rini <trini@konsulko.com>

Add config and defconfig for the Arria10 and update socfpga_common.h.
Signed-off-by: NTien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>

mx7dsabresd_secure_defconfig was not updated after moving to DM.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Switch to use DM USB.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled.
So needs to enable them together.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add basic dts for i.MX7D-SDB board.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Now that mx6sabresd_spl_defconfig can be used to boot all
mx6sabresd variants, the non-SPL targets can be safely removed.
Signed-off-by: NFabio Estevam <fabio.estvam@nxp.com>

Currently only MX6Q/QP sabresd boards are supported in SPL.

In order to also support MX6DL we need to convert to using
IOMUX_PADS and SETUP_IOMUX_PADS macros.

Other than that move the <asm/arch/mx6-ddr.h> header inclusion to the
SPL code block in order to avoid build error.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Set fdt_file env variable during board_late_init

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

This turns on ACPI S3 resume for minnowmax board.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Tested-by: NStefan Roese <sr@denx.de>

Enable TI_COMMON_CMD_OPTIONS and remove similar options
from the defconfig. Updated with savedefconfig

CMD_USB isn't enabled yet.  I have some testing to do with
musb.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Follow the exiting logic for the i.MX options when migrating this
option.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled.  In some
cases we had not already migrated to CONFIG_USB so do that as well.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

Move this entry to Kconfig.  As it is a hardware watchdog, select
HW_WATCHDOG.  While we could default to enabling this for all platforms,
it is currently only enabled by default on AM33XX, so keep that logic
today.

Cc: Roger Meier <r.meier@siemens.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot.  select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.
Signed-off-by: NTom Rini <trini@konsulko.com>

While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there.  Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely.  The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file.  Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.
Signed-off-by: NTom Rini <trini@konsulko.com>

Drop custom command prompt string in favor
of default used by U-Boot. This helps in
easier automation setup across boards.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

As commit 54925327 ("mmc: move CONFIG_GENERIC_MMC to Kconfig")
addressed, this is one of the last weird defconfigs that define
CONFIG_GENERIC_MMC without CONFIG_MMC.

Now I took a closer look at this.  Given that both CONFIG_CMD_MMC
and CONFIG_GENERIC_MMC are set for this defconfig, CONFIG_MMC should
be enabled.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

As commit 54925327 ("mmc: move CONFIG_GENERIC_MMC to Kconfig")
addressed, this is one of the last weird defconfigs that define
CONFIG_GENERIC_MMC without CONFIG_MMC.

Now I took a closer look at this.  Given that neither CONFIG_CMD_MMC
nor CONFIG_MMC is set for this defconfig, CONFIG_GENERIC_MMC
should be disabled.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.

Also drop I2C options which depend on this.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Now that we support using TI_COMMON_CMD_OPTIONS,
we dont have to enable a number of commands explicitly
in the defconfig if we enable TI_COMMON_CMD_OPTIONS.

Enable TI_COMMON_CMD_OPTIONS and regenerate the defconfig
using "make savedefconfig".

CMD_GPIO has been kept disabled because there is no GPIO
support (yet) on OMAP-L138 LCDK.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

CONFIG_DISTRO_DEFAULTS selects a number of things we want for Boston
defconfigs & generally describes what we want - to be able to boot an
arbitrary Linux distribution. Enable it in order to shorten the
defconfigs & to automatically keep up with any changes in the choice of
Kconfig symbols selected.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Enables qspi boot configuration for dra7xx platform.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>

SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Set fdt_file env variable during board_late_init

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add mipi dsi configs for rk3399 evb board
Signed-off-by: NEric Gao <eric.gao@rock-chips.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.

Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`
Signed-off-by: NJacob Chen <jacob-chen@iotwrt.com>

Set ethernet mac address in late init for Tinker Board,
prevents getting a random mac address each boot.

Read mac address from eeprom, first 6 bytes from m24c08@50.
Same as /etc/init.d/rockchip.sh on Tinker OS.
Signed-off-by: NJonas Karlman <jonas@kwiboo.se>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The file is from evb-rk3399_defconfig with changes:
- use rk3399-firefly dtb
- re-order by make savedefconfig
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Enable gmac for evb-rk3399.

Change-Id: I85e35667e08e22e38577e63eb0e65731fc9c69b6
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>

1. add Kconfig for rockchip video driver, so that video port can be
selected as needed.
2. move VIDEO_ROCKCHIP option to new Kconfig for concision.
Signed-off-by: NEric Gao <eric.gao@rock-chips.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Drop indenting in Kconfig:
Signed-off-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>