Use more safer refresh time value for 6GB LPDDR4 on this EVK board.
Update the parameters for every frequency point.
Signed-off-by: NYe Li <ye.li@nxp.com>
Reviewed-by: NJacky Bai <ping.bai@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

After switching to new LPDDR4 firmware 202006 version, have to
update the LPDDR4 timing accordingly from RPA tool.
Signed-off-by: NYe Li <ye.li@nxp.com>
Tested-by: NSherry Sun <sherry.sun@nxp.com>
Tested-by: NJacky Bai <ping.bai@nxp.com>
Reviewed-by: NJacky Bai <ping.bai@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add inline ECC support for lpddr4 on imx8mp-evk. And add a config which
can enable/disable inline ECC feature for lpddr4 on imx8mp-evk board.
Signed-off-by: NSherry Sun <sherry.sun@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

These files should not be in U-Boot repo
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Update PMIC to use PCA9540, the legacy board not supported by NXP
Signed-off-by: NYe Li <ye.li@nxp.com>

Update LPDDR4 script to sync with v2020.04 u-boot
Signed-off-by: NYe Li <ye.li@nxp.com>

The static ethernet link type config code is no more needed because now handled by
the meson8b glue driver, delete it.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

Update clock/pll setup, ddr, MIOs based on 2020.2 hw design.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add missing configurations file for zcu208 and zcu216.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.

Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: NAlexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: NKever Yang <kever.yang@rock-cihps.com>

NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.

The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].

[1] https://github.com/torvalds/linux/commit/e7a095908227fb3ccc86d001d9e13c9ae2bef8e6Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

On Puma we have the environment at an offset of 16 kiB.
On the eMMC this gives us 16 kiB for the environment before the SPL starts.
On the SPI NOR we also have 16 kiB until end of flash.
So let's increase the environment size from 8 kiB to its maximum
of 16 kiB for both MMC and SPI NOR.
Signed-off-by: NChristoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: NHeiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Provide the model information through sysinfo so that it shows up on
boot. For memconfig 4 pins are provided, for 16 combinations. For SKU
ID there are two options:

   - two pins provided in a ternary arrangement, for 9 combinations.
   - reading from the EC

Add a binding doc and drop the unused #defines as well.

Example:

   U-Boot 2021.01-rc5

   CPU:   Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
   DRAM:  3.9 GiB
   MMC:   sdmmc@1b,0: 1, emmc@1c,0: 2
   Video: 1024x768x32 @ b0000000
   Model: Google Coral (memconfig 5, SKU 3)

This depends on the GPIO series:

   http://patchwork.ozlabs.org/project/uboot/list/?series=228126Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NBin Meng <bmeng.cn@gmail.com>

It is possible to boot U-Boot for chromebook_coral either 'bare metal' or
from coreboot. In the latter case we want to provide access to the coreboot
sysinfo tables. Move the definitions into a file available to any x86
board.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These GPIOs are needed later if Chromium OS verified boot is running,
so free them after use.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move sandbox_spl over to use OF_PLATDATA_INST. Create a new board to
test the case when this is not enabled, since we will be keeping that
code around for several months and want to avoid regressions.

Skip the dm_test_of_plat_dev() test since driver info is not available
for OF_PLATDATA_INST.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NSimon Glass <sjg@chromium.org>

The User Guide contains handy things like block diagrams and DIP switch
settings and it's even available on the public web. Add a link to it in
the README.
Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add the FAT environment driver to the priority list.

When testing the UEFI sub-system the EFI system partition is formatted with
FAT so it is reasonable to store the environment there.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Add the MT8183 pumpkin board support.
Signed-off-by: NFabien Parent <fparent@baylibre.com>

Init USB Ether if CONFIG_USB_ETHER is enabled.
Signed-off-by: NFabien Parent <fparent@baylibre.com>

More than one pumpkin board has been made with different MediaTek SoCs.
Rename the pumpkin board to follow the naming convention of all
other MediaTek boards and also to not be confusing when other pumpkin
boards will be added in follow-up commits.
Signed-off-by: NFabien Parent <fparent@baylibre.com>

Enable building SPL for EK874 board which is based on R8A774C0 SoC.
Signed-off-by: NLad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: NBiju Das <biju.das.jz@bp.renesas.com>

The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).

This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.

DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: NLad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: NBiju Das <biju.das.jz@bp.renesas.com>

The HiHope RZ/G2H board from HopeRun consists of main board
(HopeRun HiHope RZ/G2H main board) and sub board(HopeRun
HiHope RZ/G2H sub board). The HiHope RZ/G2H sub board sits
below the HiHope RZ/G2H main board.

This patch adds the required board support to boot HopeRun HiHope
RZ/G2H board.
Signed-off-by: NBiju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: NLad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

The HiHope RZ/G2N board from HopeRun consists of main board
(HopeRun HiHope RZ/G2N main board) and sub board(HopeRun
HiHope RZ/G2N sub board). The HiHope RZ/G2N sub board sits
below the HiHope RZ/G2N main board.

This patch adds the required board support to boot HopeRun HiHope
RZ/G2N board.
Signed-off-by: NBiju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: NLad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.

This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: NBiju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: NLad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

Remove board_early_init_f() and board_late_init() callbacks for stm32
boards as the corresponding flags (CONFIG_BOARD_LATE_INIT and
CONFIG_BOARD_EARLY_INIT_R) are now disabled.
Signed-off-by: NPatrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: NPatrick Delaunay <patrick.delaunay@foss.st.com>

Check whether user has explicitly defined the mmc device to use
in mmc_get_env_dev() with CONFIG_SYS_MMC_ENV_DEV.

On STMicroelectronics boards the used mmc device for environment is
the instance of boot device provided by the ROM code; the mmc instance
is configured by alias in device tree. The used partition is defined in
device tree with u-boot,mmc-env-partition = "ssbl".

This patch allows to override this selection for the support of customer
boards without alias; for example when SDMMC1 is not used and ENV in
mmc0=SDMMC2, user can force the value: CONFIG_SYS_MMC_ENV_DEV = 0.

On STMicroelectronics boards, the current behavior is kept with
CONFIG_SYS_MMC_ENV_DEV = -1.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@foss.st.com>

Add CONFIG_CMD_STM32PROG_SERIAL and CONFIG_CMD_STM32PROG_USB to
independently select the support of UART or USB communication for
STM32CubeProgrammer.

For serial boot over UART, user can deactivate CONFIG_CMD_STM32PROG_SERIAL
to use U-Boot console of binary loaded by UART (for board bring-up for
example).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@foss.st.com>

Since commit d5d726d3 ("configs: stm32mp1: only support SD card after
NOR in bootcmd_stm32mp"), the stm32mp1 boards only support SD card after
NOR boot device, so the MTD partitions for nand0 or spi-nand0 are useless
(no need of "UBI" partition in nand0 or spi-nand0).

This patch removes these nand MTD update for nor boot and simplify nand0
and spi-nand0 support (remove the mtd_boot variable).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: NPatrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@foss.st.com>

board/emulation is the place for other QEMU targets like x86, arm,
riscv. Let's move the qemu-ppce500 board codes there.

List me as a co-maintainer for this board.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

This function is not called anywhere. Only fsl_ddr_sdram_size() is
necessary [1] for QEMU. Drop it.

[1] arch/powerpc/cpu/mpc85xx/cpu.c::dram_init()
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Now that we have switched to CONFIG_OF_CONTROL, and we can use the
env variable 'fdtcontroladdr' directly instead of creating one that
is duplicated.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

After U-Boot is relocated to RAM already, the previous temporary FDT
virtual-physical mapping that was used in the pre-relocation phase
is no longer needed. Let's delete the mapping.

get_fdt_virt() might be used before and after relocation, update it
to return different virtual address of FDT.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

By default the QEMU ppce500 machine connects a VirtIO NET to the
PCI controller, although it can be replaced to an e1000 NIC via
additional command line options.

Now that we have switched over to DM PCI, VirtIO support becomes
possible. This commit enables the support.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

ft_board_setup() is now empty. Drop it.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

At present the board supports non-DM version PCI and E1000 drivers.
Switch over to use DM ETH and PCI by:

- Rewrite the PCI address map functions using DM APIs
- Enable CONFIG_MISC_INIT_R to do the PCI initialization and
  address map
- Drop unnecessary ad-hoc config macros
- Remove board_eth_init() in the board codes
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

The QEMU ppce500 target integrates 2 NS16550 serial ports. Switch
over to use the DM version of the driver by:

- drop unnecessary ad-hoc config macros
- add get_serial_clock() in the board codes
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

The QEMU ppce500 machine generates a device tree blob and passes
it to U-Boot during boot. Let's enable OF_CONTROL with OF_BOARD
and provide board_fdt_blob_setup() in the board codes.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

This function does nothing. Drop it.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>