- 06 3月, 2015 11 次提交
-
-
由 Albert ARIBAUD \(3ADEV\) 提交于
This patch extends OMAP3 support for AM/DM37xx and introduces the AM3703-based Quipos Cairo board. Signed-off-by: NAlbert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Hannes Petermaier 提交于
For some cases it is necessary to modify temporaly the bootcommand. This can be done by writing into the Scratchregister a specific value: * 0xCC - modify bootcmd "run netboot" * 0xCD - modify bootcmd "run netscript" * 0xCE - modify bootcmd "run mmcboot" the environment in flash is NOT overwritten. Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
vxWorks needs several parameters which are set by the bootloader und his environment. So we form a vxWorks bootline and pass the result to vxWorks on a predefined address. Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
The board has been redesigned, therefore we need from now other I/O Pins to mux and handle. Older boards aren't supported from now anymore. Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
remove unnary '#define ETHLED_ORANGE (96+16) /* GPIO3_16 */' Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
On boards were we have no NAND-flash soldered, we want to use those free pins as regular gpio. Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
since we have a dtb blob programmed on the board we try to setup the cpsw interface with the programmed mac. If this method fails, we fall back to the device-fuses. Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
由 Hannes Petermaier 提交于
a summary screen to the lcd. Values are taken from environment and or devicetree blob. Signed-off-by: NHannes Petermaier <oe5hpm@oevsv.at>
-
- 05 3月, 2015 2 次提交
-
-
由 Stefano Babic 提交于
commit d9f43c8f sets get_reset_cause() as static, but this conflicts with mx5 where its prototype is in sys_proto.h. Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco, factorizing the call for this board. Signed-off-by: NStefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org>
-
由 Simon Glass 提交于
Use the full driver model GPIO and serial drivers in SPL now that these are supported. Since device tree is not available they will use platform data. Remove the special SPL GPIO function as it is no longer needed. This is all in one commit to maintain bisectability. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 04 3月, 2015 3 次提交
-
-
由 Przemyslaw Marczak 提交于
This commit removes the dram reservation from board file, because it is done in a common code. Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Since more than one board requires memory reservation for the secure firmware, the reservation code can be made in a common code. Now, to reserve some part of the the last bank, board config should define: - CONFIG_TZSW_RESERVED_DRAM - len in bytes - CONFIG_NR_DRAM_BANKS - number of memory banks Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Cc: Akshay Saraswat <akshay.s@samsung.com> Cc: Hyungwon Hwang <human.hwang@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Łukasz Majewski 提交于
This patch suppress following warning: board/samsung/common/board.c:95:32: warning: iteration 4u invokes undefined behavior [-Waggressive-loop-optimizations] addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE); ^ board/samsung/common/board.c:94:2: note: containing loop about possible signed integer overflow at gcc 4.8.2 (odroid board) Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 03 3月, 2015 2 次提交
-
-
由 Sinan Akman 提交于
Signed-off-by: NSinan Akman <sinan@writeme.com>
-
由 Michal Simek 提交于
Add basic Xilinx ZynqMP arm64 support. Serial and SD is supported. It supports emulation platfrom ep108 and QEMU. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 02 3月, 2015 5 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Fabio Estevam 提交于
With UMS support we are able to flash the eMMC from U-boot, which is very convenient. Add UMS support to make the eMMC flashing process easier. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NOtavio Salvador <otavio@ossystems.com.br>
-
由 Fabio Estevam 提交于
Pass the same pad configuration as done in the kernel so that OTG1_ID pin can properly work in device mode. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Marcel Ziswiler 提交于
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Fabio Estevam 提交于
Currently there is no support for MC34704 PMIC in the mainline kernel. Turn on the LCD supply via bootloader for the time being, so that we could use the LCD in the kernel. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 26 2月, 2015 2 次提交
-
-
由 Inha Song 提交于
This change is required after updated dfu_alt_system/boot declarations. Signed-off-by: NInha Song <ideal.song@samsung.com> Tested-by: NLukasz Majewski <l.majewski@samsung.com> [Test HW: Odroid U3 (Exynos 4412)] Acked-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
This common call can be used for setting proper entities based on dfu command arguments. The config: CONFIG_SET_DFU_ALT_INFO, was used only for few configs, and now it is common. The board file should implement: - set_dfu_alt_info() function Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Tested-by: NLukasz Majewski <l.majewski@samsung.com> [Test HW: Odroid U3 (Exynos 4412)]
-
- 25 2月, 2015 15 次提交
-
-
由 Vladimir Barinov 提交于
This adds GPIO configuration and initialization function of SDHI on Silk board Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Vladimir Barinov 提交于
Fix typo in device declaration Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Vladimir Barinov 提交于
Disable pull-ups on ethrenet lines Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Vladimir Barinov 提交于
Use gpio_direction_output instead of gpio_set_value since the latter does not set output GPIO direction. Signed-off-by: NValentine Barshak <valentine.barshak+renesas@cogentembedded.com> Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Vladimir Barinov 提交于
Porter is an entry level development board based on R-Car M2 SoC (R8A7791) This commit supports the following peripherals: - SCIF, I2C, Ethernet, QSPI, SD, USB Host Signed-off-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Lager board has two SDHI port as SDHI0 and SDHI2. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Gose board has three SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Koelsch board has three SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Alt board has two SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Silk board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Alt board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Lager board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Gose board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Koelsch board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Masahiro Yamada 提交于
This is still a non-generic board. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NSughosh Ganu <urwithsughosh@gmail.com> Cc: Syed Mohammed Khasim <sm.khasim@gmail.com> Acked-by: NMarek Vasut <marex@denx.de>
-