Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>

Added macros to read SOM information from the I2C
EEPROM.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>

Enable booting from NAND support from AM335x boards as well as
environment in NAND.
Signed-off-by: NIlya Yanok <ilya.yanok@cogentembedded.com>

Enable NAND support for AM335X boards.
Signed-off-by: NIlya Yanok <ilya.yanok@cogentembedded.com>

Modify tegra-common-post.h's BOOTCOMMAND definition to use the generic
filesystem command load rather than separate fatload and ext2load.
This removes the need to iterate over supported filesystem types in the
boot command.

This requires editing all board config headers to enable the new
commands. The now-unused commands are left enabled to assue backwards
compatibility with any user scripts. Boards (all from Avionic Design)
which define custom BOOTCOMMAND values are not affected.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
tegra generic fs cmds fixup
Signed-off-by: NTom Warren <twarren@nvidia.com>

The NAND defines ended up before this include file, but should be after
it, so it doesn't become a post-pre-NAND.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Now that we are using the new CONFIG_SYS_NAND_SELF_INIT setup, we don't
need CONFIG_SYS_NAND_BASE. Punt it.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

TrimSlice's USB1 port has two purposes; it either acts as a device port
hosting Tegra's USB recovery protocol, or acts as a host port connected
to the internal USB->SATA bridge chip, which may in turn be connected to
an SSD or HDD. Add the appropriate device tree and board configuration
options to enable this port as a host port, and route the port to the
SATA bridge using the VBUS GPIO.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Enable the Seaboard's 16-bit LCD and use it as the console.
Signed-off-by: NMayuresh Kulkarni <mkulkarni@nvidia.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

For tegra we want to enable the cache for the LCD. This is easier if
we can avoid using L2 page tages, so align the LCD to a section
boundary.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

This provides an option for the LCD to flush the dcache after each update
(puts, scroll or clear).
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

The normal alignment is PAGE_SIZE, but if this is defined, we can support
other alignments.

The motivation for this change is to make the display section-aligned on
ARM so that we can easily turn off data caching for the frame buffer region
without resorting to level 2 page tables.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Add support for the LCD peripheral at the Tegra2 SOC level. A separate
LCD driver will use this functionality to configure the display.
Signed-off-by: NMayuresh Kulkarni <mkulkarni@nvidia.com>
Mayuresh Kulkarni:
- changes to remove bitfields and clean up for submission
Signed-off-by: NSimon Glass <sjg@chromium.org>
Simon Glass:
- simplify code, move clock control into here, clean-up
Signed-off-by: NTom Warren <twarren@nvidia.com>

The pulse width/frequency modulation peripheral supports generating
a repeating pulse. It is useful for controlling LCD brightness.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

These platforms don't include dcache support. Define CONFIG_SYS_DCACHE_OFF
so that functions don't try to call non-existent routines like
flush_dcache_range().
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

The mx5 lowlevel_init.S contains board-specific code based on the reference
design. Let's keep it since it avoids creating new lowlevel_init files and it
may be used by many boards. But add a config to make it optional in order not to
cause issues on boards not following this part of the reference design.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matt Sealey <matt@genesi-usa.com>
Acked-by: NStefano Babic <sbabic@denx.de>

One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NJason Liu <r64343@freescale.com>

One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NJason Liu <r64343@freescale.com>

One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

Add support for the OTG port on the mx35pdk Personality board.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: NStefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>

Use EHCI MXC configuration options for i.MX25.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matthias Weisser <weisserm@arcor.de>

Make EHCI power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so move them to
ehci-fsl.h so that all MXC SoCs can use them.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

This patch enables SPI Booting for EXYNOS5
Signed-off-by: NRajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch enables SPI driver for EXYNOS5.
Signed-off-by: NRajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: NHatim Ali <hatim.rv@samsung.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch enables sound support for EXYNOS5
Signed-off-by: NRajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: NChander Kashyap <chander.kashyap@linaro.org>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch adds driver for I2S interface specific to samsung.
Signed-off-by: NR. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: NRajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch add support for display on Universal C210 board.
Width of displyed logo must be not bigger than 480 pixel and
is limited by width of the screen.
Tizen logo size is 520x120 pixels and should be resized.
Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
CC: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Add LDO7 and LDO17 macros to max8998_pmic.h necessary to power on the LCD.
Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch use software spi on Samsung Universal C210 board.
Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch enables MAX77686 pmic chip for SMDK5250.
Signed-off-by: NRajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

This patch adds driver and register definitions for PMIC chip
MAX77686.
Signed-off-by: NRajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: NLukasz Majewski <l.majewski@samsung.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Low level initialisation is done by another bootloader
Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>