- 27 5月, 2007 2 次提交
-
-
由 Bartlomiej Sieka 提交于
Both CFG_PCISPEED_66 and CFG_IPBSPEED_133 are misnamed, as defining them does not cause PCI or IPB clocks to run at the specified speed. Instead, they configure divisors used to calculate said clocks. This patch renames the defines according to their real function. Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com> Acked-by: NBartlomiej Sieka <tur@semihalf.com>
-
由 Bartlomiej Sieka 提交于
Signed-off-by: NJan Wrobel <wrr@semihalf.com> Signed-off-by: NMarian Balakowicz <m8@semihalf.com> Acked-by: NBartlomiej Sieka <tur@semihalf.com>
-
- 10 5月, 2007 1 次提交
-
-
由 Piotr Kruszynski 提交于
definition.
-
- 08 5月, 2007 5 次提交
-
-
由 Piotr Kruszynski 提交于
-
由 Bartlomiej Sieka 提交于
environment.
-
由 Bartlomiej Sieka 提交于
eliminates networking problems in Linux (timeouts).
-
由 Bartlomiej Sieka 提交于
to allow booting of FDT-expecting kernels.
-
由 Bartlomiej Sieka 提交于
current PHY initalization code (tftp timeouts all the time). This commit temporarily disables PHY initalization sequence to make the networking operational, until a fix is found.
-
- 09 2月, 2007 1 次提交
-
-
由 Bartlomiej Sieka 提交于
-
- 24 1月, 2007 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Bartlomiej Sieka 提交于
-
- 23 1月, 2007 3 次提交
-
-
由 Bartlomiej Sieka 提交于
currently sectors 0-3. Sector 3 does not need to be protected, though (U-boot occupies sectors 0-1 and the environment sector 2). This commit fixes this, i.e., only sectors 0-2 are protected.
-
由 Bartlomiej Sieka 提交于
"mii device" results in "Unexpected exception"). Fixing this properly requires some clean-up in the FEC drivers infrastructure for ColdFire, so this commit disables MII commads for now.
-
由 Bartlomiej Sieka 提交于
Identification Register (CIR).
-
- 20 1月, 2007 4 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
if you must swap the bytes between reading/writing. (Needed for the SC3 board) Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 19 1月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 18 1月, 2007 6 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Heiko Schocher 提交于
The EBC Configuration Register is now by CFG_EBC_CFG definable Added JFFS2 support for the SC3 board. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 17 1月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 16 1月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 15 1月, 2007 4 次提交
-
-
由 Wolfgang Denk 提交于
Some code cleanup.
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 14 1月, 2007 1 次提交
-
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 13 1月, 2007 8 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
Haiying Wang's modification to the reset command was broken, undo it. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Stefan Roese 提交于
Also display enabled/disabled RAID 6 support for 440SP/440SPe PPC's. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Now the board revision and the current PCI bus speed are printed after the board message. Also the EBC initialising is now done via defines in the board config file. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Now the board revision and the current PCI bus speed are printed after the board message. Also the EBC initialising is now done via defines in the board config file. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Now the board revision and the current PCI bus speed are printed after the board message. Signed-off-by: NStefan Roese <sr@denx.de>
-