This reverts commit 318a7a57.

The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

This is not required. The MMC core sends CMD0 right after the
initialization and it serves the same purpose.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA

Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

The response type of CMD25 is R1 instead of R1b.
Signed-off-by: NAkio Hirayama <hirayama.akio@socionext.com>
[masahiro: add log ]
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Card detect function implemented for SDHCI framework.
Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch reads cd-gpio property from devicetree
Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.
Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Removed MMC_CAP_NONREMOVABLE, MMC_CAP_NEEDS_POLL macros from
mvebu_mmc.h to avoid redefining of these macros when compiled with
mvebu based configs.
Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

- First round of TI Davinci updates
- Some OMAP3 DM updates
- Other misc updates

This test is currently broken so disable it for now.

Cc: Ramon Fried <ramon.fried@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

Since we have limited resources in SPL, it is the best interest
to keep the SPL as small as possible and that includes the DTB.
There are a few items in the device tree that can be removed,
because these boards don't use them.
Signed-off-by: NAdam Ford <aford173@gmail.com>

Fixed regulators don't have a set_value method. Therefore, trying to
set their value will always return -ENOSYS.
Signed-off-by: NSven Schwermer <sven@svenschwermer.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.

for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: NHeiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: NPatrick Delaunay <patrick.delaunay@st.com>

The MMC card-detect pin was incorrectly defined which was fixed.
This patch resync's the dts and removes the u-boot specific fix.
Signed-off-by: NAdam Ford <aford173@gmail.com>

The da850.dtsi file had some changes.  This patch pulls in the
changes from Kernel 5.1.9
Signed-off-by: NAdam Ford <aford173@gmail.com>

With a recent update to the pinctrl-single driver and the fact
that the da850evm has both DM and OF_CONTROL working in both SPL
and U-Boot, some of the manual pinmuxing can be setup to only
be activated when either the driver doesn't have DM for it, or
when CONFIG_PINMUX isn't available (only during SPL).  If the
code ever shrinks enough to support PINCTRL in SPL, a lot of this
can go away.  This also remove some manual pinmuxing not needed
by SPL to give SPL a little more breathing room.
Signed-off-by: NAdam Ford <aford173@gmail.com>

The TI Davinci (da850/l138/am1808) use pinctrl-single,bits for
pinmuxing peripherals.  This patch allosw the pinctrl-single
driver to parse the pinctrl-single,bits options and correctly
setup devices.
Signed-off-by: NAdam Ford <aford173@gmail.com>

The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support.  Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.

To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol.  Finally, in
the case of a few boards we really do need the full printf
functionality.
Signed-off-by: NTom Rini <trini@konsulko.com>

Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the regulator support in SPL.
Signed-off-by: NKeerthy <j-keerthy@ti.com>

Add SPL_PMIC configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the pmics in SPL.
Signed-off-by: NKeerthy <j-keerthy@ti.com>

Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.

CPU  : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
eth0: ethernet@4a100000

Working:
 - Eth0
 - i2C
 - MMC/SD
 - NAND
 - UART
 - USB (host)

Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")
Signed-off-by: NNiel Fourie <lusus@denx.de>
Signed-off-by: NParthiban Nallathambi <pn@denx.de>
Reviewed-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>
Tested-by: NMarek Vasut <marex@denx.de>

This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.

The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: NDavid Lechner <david@lechnology.com>

Signed-off-by: NMichael Walle <michael@walle.cc>

This commit addresses the following warning, when _NOT_ USB_MUSB_HOST:

[...]
  CC      drivers/usb/gadget/f_mass_storage.o
  CC      drivers/usb/musb-new/omap2430.o
  CC      drivers/usb/gadget/f_fastboot.o
  CC      env/common.o
  CC      env/env.o
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’:
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion]
  ret = musb_register(&platdata->plat,
      ^
  LD      drivers/usb/host/built-in.o
  CC      drivers/usb/gadget/f_sdp.o
  CC      fs/ext4/ext4fs.o
[...]
Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>

This addresses the following warning message:

===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================

As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>

Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>

add m41t11 support in ds1307 driver. changes:

- add compatible string for m41t11
- check if RTC clock is running, if not
  enable the clock
Signed-off-by: NHeiko Schocher <hs@denx.de>

When MMC_TINY is enabled, support for only one MMC device
is provided. Boards that register more than one device,
will just write over mmc_static keeping only the last one
registered.

This commit prevents this, keeping only the first MMC
device created. A debug warning message is added, if nothing
else, as a hint/documentation for developers.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>

The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>

Add sub-command 'env info' to display environment information:
- env_valid : is environment valid
- env_ready : is environment imported into hash table
- env_use_default : is default environment using

This command can be optionally used for evaluation in scripts:
[-d] : evaluate whether default environment is used
[-p] : evaluate whether environment can be persisted
The result of multiple evaluations will be combined with AND.
Signed-off-by: NLeo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: NMark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
[trini: Do not enable by default]
Signed-off-by: NTom Rini <trini@konsulko.com>

`if (!strncmp(dev->name, name, strlen(name)))` might find out
the wrong device, it might find out `dram_pll_ref_sel`, when name is
`dram_pll`. So use strcmp to avoid such issue.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

"keyb" is not the real device name, "keyb@3" is.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

"adc" is not the real device name, "adc@0" is.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Use the uclass_first_device_check and uclass_next_device_check functions
instead of uclass_first_device and uclass_next_device in pci_init. This
ensures that all PCI devices are tried to be probed. Currently if a
device fails to probe, the enumeration stops and the devices which come
after the failed device are not probed.
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: NStefan Roese <sr@denx.de>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Convert the board to support the USB and video driver model and remove
the unnecessary code.

Convert the board to support the USB and video driver model and remove
the unnecessary code.

- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3

- SPL SATA enhancements to allow booting from RAW SATA device
  needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
  (Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
  for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)

UniPhier SoC updates for v2019.10

- import DT updates from Linux

- add UniPhier SPI controller driver

- make U-Boot image for 64bit SoCs position independent

- tidy up various init code for next generation SoCs

- misc cleanups

- spear platform improvements
- Android BCB support
- Cadence PCIe endpoint driver