ARM: dts: omap3-evm: Sync dts(i) files from Linux 5.1.5

Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>

arch/arm/dts/omap3-evm-37xx.dts

@@ -90,19 +90,19 @@
 			label = "X-Loader";
 			reg = <0 0x80000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "U-Boot";
 			reg = <0x80000 0x1c0000>;
 		};
-		partition@0x1c0000 {
+		partition@1c0000 {
 			label = "Environment";
 			reg = <0x240000 0x40000>;
 		};
-		partition@0x280000 {
+		partition@280000 {
 			label = "Kernel";
 			reg = <0x280000 0x500000>;
 		};
-		partition@0x780000 {
+		partition@780000 {
 			label = "Filesystem";
 			reg = <0x780000 0x1f880000>;
 		};

arch/arm/dts/omap3-evm-common.dtsi

@@ -122,6 +122,7 @@
 };
 
 &mmc2 {
+	interrupts-extended = <&intc 86 &omap3_pmx_core 0x12e>;
 	vmmc-supply = <&wl12xx_vmmc>;
 	non-removable;
 	bus-width = <4>;
@@ -132,8 +133,10 @@
 	wlcore: wlcore@2 {
 		compatible = "ti,wl1271";
 		reg = <2>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 149 */
+		/* gpio_149 with uart1_rts pad as wakeirq */
+		interrupts-extended = <&gpio5 21 IRQ_TYPE_EDGE_RISING>,
+				      <&omap3_pmx_core 0x14e>;
+		interrupt-names = "irq", "wakeup";
 		ref-clock-frequency = <38400000>;
 	};
 };

arch/arm/dts/omap3-evm-processor-common.dtsi

@@ -86,6 +86,10 @@
 			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
 			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
 			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1)	/* sdmmc2_dat4.sdmmc2_dir_dat0 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1)	/* sdmmc2_dat5.sdmmc2_dir_dat1 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1)	/* sdmmc2_dat6.sdmmc2_dir_cmd */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1)	/* sdmmc2_dat7.sdmmc2_clkin */
 		>;
 	};
 
@@ -127,9 +131,13 @@
 		>;
 	};
 
+	/*
+	 * Note that gpio_150 pulled high with internal pull to prevent wlcore
+	 * reset on return from off mode in idle.
+	 */
 	wl12xx_gpio: pinmux_wl12xx_gpio {
 		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4)		/* uart1_cts.gpio_150 */
+			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE7)		/* uart1_cts.gpio_150 */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4)		/* uart1_rts.gpio_149 */
 		>;
 	};