- 15 1月, 2020 8 次提交
-
-
由 Joris Offouga 提交于
Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Joris Offouga 提交于
For DM_ETH support , it's require to disable this config. When this config is enable, This generate a error with spl in linker script Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
Currently the following SPL hang is observed: U-Boot SPL 2020.01-rc5-00079-g797eee36 (Jan 06 2020 - 11:24:09 -0300) Trying to boot from MMC1 Card did not respond to voltage select! spl: mmc init failed with error: -95 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### Fix it by moving the eSDHC2 initialization to SPL. While at it, since this board uses DM_MMC all the esdhc board code can be removed to make the code simpler. Signed-off-by: NFabio Estevam <festevam@gmail.com>
-
由 Peng Fan 提交于
Update README to use 4.19.35_1.1.0 released firmware images. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Fabio Estevam 提交于
Only the wandboard revD1 boards have PMIC, so when running on a wandboard of different revision the following error is always shown on every boot: pmic_get() ret -19 Instead of printing this error message, move it to debug level instead. Signed-off-by: NFabio Estevam <festevam@gmail.com>
-
由 Fabio Estevam 提交于
Some i.MX8QXP MEK boards do not have MAC address stored and hang during eth driver probe: Error: ethernet@5b040000 address not set. (Board hangs) To fix this problem select CONFIG_NET_RANDOM_ETHADDR so that a valid MAC address can be used in such case. Signed-off-by: NFabio Estevam <festevam@gmail.com>
-
由 Anatolij Gustschin 提交于
Add support for Capricorn Deneb SoM variant. Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Anatolij Gustschin 提交于
Add support for i.MX8X based Capricorn Giedi SoM. Supported interfaces: GPIO, ENET, eMMC, I2C, UART. Console output: U-Boot SPL 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) Trying to boot from MMC1 Load image from MMC/SD 0x3e400 U-Boot 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) ##v01.07 CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C Model: Siemens Giedi Board: Capricorn Boot: MMC0 DRAM: 1022 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial@5a080000 Out: serial@5a080000 Err: serial@5a080000 Net: eth1: ethernet@5b050000 [PRIME] Autobooting in 1 seconds, press "<Esc><Esc>" to stop Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 11 1月, 2020 13 次提交
-
-
由 Tom Rini 提交于
Given our tests in GitLab / Azure we can use QEMU v4.2.0 for all platforms now. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
- Updated base snapshot - QEMU v4.2.0 Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
- Android image support enhancements - Assorted ARM fixes and enhancements - m68k update
-
由 Eugeniu Rosca 提交于
Trying to extend 'adtimg' functionality [1], we've been severely hit by a major limitation in the command's usage scheme. Specifically, the command's user interface appears to be too centric to getting the DTB/DTBO entry [3] based on the index of the desired DT in the image, which makes it really difficult retrieving the DT entry based on alternative criteria (e.g. filtering by id/rev fields), the latter being demanded by real life customer use-cases [1]. This went to the point of receiving below feedback from Sam [2]: -- snip -- As for 'dtimg' command: after giving it some thought, I think not much people using it yet. So in this particular case I don't have some strong preference, and if you think the 'dtimg' interface is ugly, and it overcomes "don't break interfaces" rule, maybe now is a good time to rework it (before it gets widely used). -- snip -- Given the above, rework the usage pattern from [4] to [5], in order to allow an intuitive enablement of "by id|rev" DT search [6]. [1] https://patchwork.ozlabs.org/cover/1202575/ ("cmd: dtimg: Enhance with --id and --rev options (take #1)") [2] https://patchwork.ozlabs.org/patch/1182207/#2317020 [3] https://source.android.com/devices/architecture/dto/partitions [4] Old usage adtimg dump <addr> - Print image contents adtimg start <addr> <index> <varname> - Get DT address by index adtimg size <addr> <index> <varname> - Get DT size by index [5] New usage adtimg addr <addr> - Set image location to <addr> adtimg dump - Print out image contents adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index [6] Soon-to-be-provided "by id|rev" add-on functionality adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]] - Get DT address/size/index by id|rev fields Signed-off-by: NEugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: NSam Protsenko <semen.protsenko@linaro.org>
-
由 Eugeniu Rosca 提交于
With 'dtimg.c' renamed to 'adtimg.c', now ensure the naming consistency in the internal implementation of 'adtimg.c'. No functional change intended. Signed-off-by: NEugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: NSam Protsenko <semen.protsenko@linaro.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Eugeniu Rosca 提交于
Rename the existing 'dtimg' command to 'adtimg', in order to: - Suggest the Android origins and scope - Be consistent with the upcoming 'abootimg' command (naming suggested by Simon [*]) The change in _not_ backward compatible, but its benefits outweigh its downsides, given that we don't expect active users of 'dtimg' today. Perform the rename in several steps: 1. Rename *.c file and Kconfig symbol. This should allow 'git log --follow' to properly track the history of 'adtimg.c' 2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c' ELF comparison [**] before and after shows no functional change. [*] https://patchwork.ozlabs.org/patch/1182212/#2291600 [**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o) Cc: Tom Rini <trini@konsulko.com> Signed-off-by: NEugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Glass<sjg@chromium.org> Reviewed-by: NSam Protsenko <semen.protsenko@linaro.org>
-
由 Heinrich Schuchardt 提交于
%s/devicd/device Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Rajesh Ravi 提交于
Current U-Boot has only support for psci reset. Adding support for arm psci reset2 allows passing of reset level and other platform sepcific parameters like strap settings to lowlevel psci implementation. Signed-off-by: NRajesh Ravi <rajesh.ravi@broadcom.com> Signed-off-by: NVladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
-
由 Bharat Kumar Reddy Gooty 提交于
Programs the following: 1. Redistributor PROCBASER configuration table (which is common for all redistributors) 2. Redistributor pending table (PENDBASER), for all the available redistributors. Signed-off-by: NBharat Kumar Reddy Gooty <bharat.gooty@broadcom.com> Signed-off-by: NVladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
-
由 Heinrich Schuchardt 提交于
fit_check_params() wants at least two of dflag, fflag, and lflag set. Simplify the logical constraint checking this. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Klaus H. Sorensen 提交于
If the numbers do not happen to contain any digits from [a-f], it's not clear that they are base 16. Signed-off-by: NKlaus H. Sorensen <khso@prevas.dk> Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: NLukasz Majewski <lukma@denx.de> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Philippe Reynes 提交于
In the function cmd_ut_category, the prefix is used with the function strncmp to know if the prefix should be removed from the test name, even if the prefix is NULL. To avoid this issue, we consider that a prefix NULL mean no prefix. So we only try to remove the prefix from the test_name if the prefix is not NULL, then we avoid to call the function strncmp with a NULL prefix. Reported-by: Coverity CID 281110 Fixes: 4ad4edfe ("cmd_ut: add a parameter prefix to the function cmd_ut_category") Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
-
由 Andy Shevchenko 提交于
GCC 9.x starts complaining about potential misalignment of the pointer to the array (in this case alignment=2) in the packed (alignment=1) structures. Repeating Linus' Torvalds commit 6f303d60534c in the Linux kernel. Original commit message: We already did this for clang, but now gcc has that warning too. Yes, yes, the address may be unaligned. And that's kind of the point. This in particular hides the warnings like drivers/usb/gadget/composite.c:545:23: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 545 | collect_langs(sp, s->wData); drivers/usb/gadget/composite.c:550:24: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 550 | collect_langs(sp, s->wData); drivers/usb/gadget/composite.c:555:25: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 555 | collect_langs(sp, s->wData); Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
-
- 10 1月, 2020 19 次提交
-
-
由 Holger Brunck 提交于
The M25P80 and M25P32 SPI flashes from Numonix/Micron will be replaced by Marconix MX25L80 and MX25L32 flashes. Signed-off-by: NHolger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Holger Brunck 提交于
This target is out of maintenance and can be removed. Signed-off-by: NHolger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Holger Brunck 提交于
For upcoming SECU board we have different MAC address offsets depending on which functional unit we are running. In this case we need to pass this value to the ivm_populate_env function instead of using the hard coded config option there. Signed-off-by: NHolger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Marek Vasut <marex@denx.de> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Holger Brunck 提交于
This patch only fixes a typo. Signed-off-by: NHolger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Frank Wunderlich 提交于
this adds poweroff to bananapi r2 / mt7623 / mt6323 pmic Signed-off-by: NFrank Wunderlich <frank-w@public-files.de>
-
由 Han Nandor 提交于
DS3232 is an i2c RTC with 236 bytes of battery-backed SRAM. Add an RTC driver for DS3232 device, which provides time and date support. Also read and write functions are provided, which can be used to access the SRAM memory. Signed-off-by: NNandor Han <nandor.han@vaisala.com>
-
由 Simon Goldschmidt 提交于
Most platforms do not set up gd->start_addr_sp in SPL. Since this is required for CONFIG_SPL_SYS_REPORT_SACK_F_USAGE to work correctly, set up gd->start_addr_sp in SPL to the value passed to board_init_f_init_reserve if it is not set yet. Fixes: d8c03320 ("spl: implement stack usage check") Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
由 Tom Rini 提交于
All platforms currently use the "MCFTMR" DMA timer rather than the PIT timer, so drop the MCFPIT code. Cc: Huan Wang <alison.wang@nxp.com> Cc: Angelo Dureghello <angelo@sysam.it> Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com> Cc: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NAngelo Dureghello <angelo@sysam.it>
-
由 Robert Beckett 提交于
This driver allows the use of i2c eeprom device or partition as backing store for boot counter values with DM enabled. Signed-off-by: NRobert Beckett <bob.beckett@collabora.com>
-
由 Angelo Durgehello 提交于
Add specific dm code, but maintaining this driver as is, so more in the shape of a mii library. Can be moved to dm in a further step. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
由 Angelo Durgehello 提交于
Full conversion to dm for all boards, legacy code removed. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
由 Angelo Durgehello 提交于
Full conversion to dm for all boards, legacy code removed. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
由 Angelo Durgehello 提交于
Add ColdFire fec to Kconfig. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
由 Angelo Durgehello 提交于
Add architecture-related code for dm fec support. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
由 Angelo Durgehello 提交于
Remove unneeded fec-related defines after fec moved as dm. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
由 Angelo Durgehello 提交于
Add dm eth config options for all involved ColdFire-based boards. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
由 Angelo Durgehello 提交于
Add ethernet controller overrides for all involved boards. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
由 Angelo Durgehello 提交于
Add basic ethernet controller devicetree nodes for all ColdFire families. Signed-off-by: NAngelo Durgehello <angelo.dureghello@timesys.com>
-
https://gitlab.denx.de/u-boot/custodians/u-boot-mpc83xx由 Tom Rini 提交于
- A small PR with MC8309 fixes from Rasmus.
-