- 24 10月, 2014 1 次提交
-
-
由 Simon Glass 提交于
Adjust the configuration for the am33xx boards, including beagleboard, to use driver model. Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NTom Rini <trini@ti.com>
-
- 18 4月, 2014 2 次提交
-
-
由 Nishanth Menon 提交于
Zoom1 was wrongly setup for LAN91C96. Fix it by enabling LAN9211. Signed-off-by: NNishanth Menon <nm@ti.com>
-
由 Nishanth Menon 提交于
zoom1 uses LAN9211 configured over GPMC Chip Select 1. Signed-off-by: NNishanth Menon <nm@ti.com>
-
- 24 7月, 2013 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: NTom Rini <trini@ti.com>
-
- 09 3月, 2013 2 次提交
-
-
由 Nikita Kiryanov 提交于
Add check for write protection in omap mmc driver. Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il> Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Reviewed-by: NTom Rini <trini@ti.com>
-
由 Nikita Kiryanov 提交于
Implement driver check for card detection. Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il> Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
-
- 15 5月, 2012 1 次提交
-
-
由 Jonathan Solnit 提交于
Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: NJonathan Solnit <jsolnit@gmail.com>
-
- 04 9月, 2011 1 次提交
-
-
由 Tom Rini 提交于
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc driver. This patch is based on the work done for Beagle, etc. Signed-off-by: NTom Rini <trini@ti.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 21 12月, 2010 1 次提交
-
-
由 John Rigby 提交于
It can be optimised out by the compiler otherwise resulting in obscure errors like a board not booting. This has been documented in README since 2006 when these were first fixed up for GCC 4.x. Signed-off-by: NJohn Rigby <john.rigby@linaro.org> Fix some additional places. Signed-off-by: NWolfgang Denk <wd@denx.de> Acked-By: NAlbert ARIBAUD <albert.aribaud@free.fr>
-
- 04 1月, 2010 1 次提交
-
-
由 Grazvydas Ignotas 提交于
Not all boards have both LEDs hooked, so enabling both on boards with single LED will just waste power. Make it possible to choose LEDs by adding argument to twl4030_led_init(). Using this turn on only LEDB for pandora, leave both LEDs on for all other boards, as it was before this patch. Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
-
- 15 12月, 2009 1 次提交
-
-
由 Ben Warren 提交于
A previous Commit converted the LAN91C96 Ethernet driver to using the CONFIG_NET_MULTI API, but did not include full board support. This patch finishes the job. Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 05 9月, 2009 1 次提交
-
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 29 7月, 2009 1 次提交
-
-
由 Tom Rix 提交于
Because twl4030 now has its own device files, move exiting omap3 power_init_r to a new location. power_init_r is the only function in board/omap3/common. It initializes the twl4030 power for the board and enables the led. The power part of the the function is moved to twl4030_power_init in drivers/power/twl4030.c The power compilation is conditional on the existing config variable CONFIG_TWL4030_POWER. The led part is moved to twl4030_led_init in the new file drivers/misc/twl4030_led.c The led compilation is conditional on the new config variable CONFIG_TWL4030_LED The directory board/omap3/common was removed because power_init_r was the only function in it. Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
- 28 7月, 2009 1 次提交
-
-
由 Tom Rix 提交于
The Zoom2 power reset button is on the top right side of the main board. Press and hold for about to 8 seconds to completely reset the board. Some of the beta boards have a hardware problem that prevents using this feature. If is difficult to further characterize the boards that fail. So disable resetting for all beta boards. The Zoom1 reset button is the red circle on the top right, front of the board. Press and hold the button for 8 seconds to completely reset the board. After analyzing beagle, it was determined that other boards that use the twl4030 for power managment can also make use this function. The resetting is done by the power management part of the twl4030. Since there is no existing drivers/power, add one. The compilation of power/twl4030.h is controlled by the config variable CONFIG_TWL4030_POWER Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
- 05 4月, 2009 1 次提交
-
-
由 Tom Rix 提交于
Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 14 3月, 2009 1 次提交
-
-
由 Dirk Behme 提交于
Read and store OMAP3 die ID in U-Boot environment. Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 29 1月, 2009 2 次提交
-
-
由 Dirk Behme 提交于
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here: http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kitSigned-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NJason Kridner <jkridner@beagleboard.org>
-
由 Dirk Behme 提交于
Add BeagleBoard support, common power code and README. Signed-off-by: NJason Kridner <jkridner@beagleboard.org> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-