- 04 5月, 2016 1 次提交
-
-
由 Robert P. J. Day 提交于
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
-
- 26 4月, 2016 4 次提交
-
-
由 Tom Rini 提交于
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
A number of moveconfig.py runs have left a instances of multiple empty lines in a row. Correct this to a single empty line. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 3月, 2016 2 次提交
-
-
由 Simon Glass 提交于
There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
Move this option to Kconfig and tidy up existing boards. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 28 1月, 2016 2 次提交
-
-
由 Aneesh Bansal 提交于
CONFIG_CMD_BLOB must be defined in case of Secure Boot. It was earlier defined in all config files. The definition has been moved to a common file which is included by all configs. Signed-off-by: NAneesh Bansal <aneesh.bansal@nxp.com> Acked-by: NRuchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Aneesh Bansal 提交于
The file fsl_secure_boot.h must be included in config file for Secure Boot. This is not required to be protected by any macro. CONFIG_FSL_CAAM must be defined and CONFIG_CMD_HASH should be turned on. The above was missing in some config files and all files have been made uniform in this respect. Signed-off-by: NAneesh Bansal <aneesh.bansal@nxp.com> Acked-by: NRuchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 25 11月, 2015 2 次提交
-
-
由 Bin Meng 提交于
There are already Kconfig options for SPI flash drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bin Meng 提交于
There are already Kconfig options for SPI drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
- 22 11月, 2015 1 次提交
-
-
由 Thomas Chou 提交于
Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py. Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
-
- 30 10月, 2015 1 次提交
-
-
由 Gong Qianyu 提交于
For most PPC platforms, they will call the first get_clocks() in init_sequence_f[] as they define CONFIG_PPC. CONFIG_SYS_FSL_CLK is then defined to call the second get_clocks(), which should be redundant for PPC. Signed-off-by: NGong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 25 10月, 2015 2 次提交
-
-
由 Gong Qianyu 提交于
get_clocks() should not be limited by ESDHC. Signed-off-by: NGong Qianyu <Qianyu.Gong@freescale.com>
-
由 Masahiro Yamada 提交于
We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
- 21 10月, 2015 1 次提交
-
-
由 Bin Meng 提交于
Convert CONFIG_CMD_ELF to Kconfig and tidy up affected boards. Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
- 02 9月, 2015 1 次提交
-
-
由 York Sun 提交于
For e6500 and e5500 SoCs, it was intended to put init_ram address in ccsr reserved space. It is no longer true since SerDes module took the space. Move it to another reserved space at CCSR + 0x03c000. Signed-off-by: NYork Sun <yorksun@freescale.com>
-
- 22 8月, 2015 1 次提交
-
-
由 Simon Glass 提交于
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected boards. Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 26 6月, 2015 2 次提交
-
-
由 Joe Hershberger 提交于
This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Joe Hershberger 提交于
Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 02 6月, 2015 1 次提交
-
-
由 Lars Poeschel 提交于
CONFIG_NET_MULTI is not used anywhere and thus can safely be removed from the configs. Acked-by: NMarek Vasut <marex@denx.de> Acked-by: NViresh Kumar <viresh.kumar@linaro.org> Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
-
- 01 6月, 2015 2 次提交
-
-
由 Joe Hershberger 提交于
This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a83 (commands: add more command entries in Kconfig). Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Another shell scripting command that has not been moved. Moved using tools/moveconfig.py using these settings: CMD_SETEXPR bool n y Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
-
- 21 4月, 2015 3 次提交
-
-
由 Shengzhou Liu 提交于
CONFIG_PHY_AQ1202 is no longer needed, use CONFIG_PHY_AQUANTIA. Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Shengzhou Liu 提交于
Support SODIMM D3XP12081XL10AA 1866MT/s on T2080RDB. Enable CONFIG_CMD_MEMTEST as well. Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Ying Zhang 提交于
The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: NYing Zhang <b40530@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 31 3月, 2015 1 次提交
-
-
由 Peter Tyser 提交于
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some time and a more generic method of NAND verification now exists in U-Boot. Signed-off-by: NPeter Tyser <ptyser@xes-inc.com> Tested-by: NHeiko Schocher <hs@denx.de> Acked-by: NHeiko Schocher <hs@denx.de>
-
- 16 12月, 2014 1 次提交
-
-
由 Jeffrey Ladouceur 提交于
Not all portals might be managed and therefore visible. Set the isdr register so that the corresponding isr register won't be set. This is required when supporting power management. Signed-off-by: NJeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 23 11月, 2014 1 次提交
-
-
由 Masahiro Yamada 提交于
Since commit 0defddc8 (config: Add a default CONFIG_SYS_PROMPT), each board header does not need to define CONFIG_SYS_PROMPT as long as it uses the default prompt "=> ". Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
- 17 10月, 2014 2 次提交
-
-
由 Ruchika Gupta 提交于
Enable blob commands for platforms having SEC 4.0 or greater for secure boot scenarios Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Ruchika Gupta 提交于
Enable CAAM in platforms supporting the hardware block. Hash command enabled along with hardware accelerated support for SHA-1 and SHA-256 for platforms which have CAAM block. Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 31 7月, 2014 1 次提交
-
-
由 Masahiro Yamada 提交于
Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig. Remove the redundant definition in config headers. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
- 30 7月, 2014 1 次提交
-
-
由 Masahiro Yamada 提交于
We are about to switch to Kconfig in the next commit. But there are something to get done beforehand. In Kconfig, include/generated/autoconf.h defines boolean CONFIG macros as 1. CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1. Otherwise, when switching to Kconfig, the build log would be sprinkled with warning messages like this: warning: "CONFIG_SPL" redefined [enabled by default] Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
- 24 7月, 2014 1 次提交
-
-
由 Shengzhou Liu 提交于
Tested with NOR boot and NAND boot on T2080QDS and T2080RDB. Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
-
- 23 7月, 2014 1 次提交
-
-
由 Shaohui Xie 提交于
On some platforms, CSn FTIM2.TCH is set to zero which is invalid, an invalid hold time makes DUT timing variances, whether it works or not on luck. Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 17 5月, 2014 2 次提交
-
-
由 Liu Gang 提交于
The new 768KB u-boot image size requires changes for SRIO/PCIE boot. These addresses need to be updated to appropriate locations. The updated addresses are used to configure the SRIO/PCIE inbound windows for the boot, and they must be aligned with the window size based on the SRIO/PCIE modules requirement. So for the 768KB u-boot image, the inbound window cannot be set with 0xfff40000 base address and 0xc0000 size, it should be extended to 1MB size and the base address can be aligned with the size. Signed-off-by: NLiu Gang <Gang.Liu@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Kim Phillips 提交于
AFAICT, c=ffe does nothing and was a typo from the original commit d1712369 "powerpc/p4080: Add support for the P4080DS board" and just kept on getting duplicated in subsequently added board config files. Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Acked-by: NEdward Swarthout <ed.swarthout@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 13 5月, 2014 2 次提交
-
-
由 Shengzhou Liu 提交于
Enable errata A006261, A006593, A006379 for T208x. Additionally enable CONFIG_CMD_ERRATA for T2080RDB. Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
-
由 Masahiro Yamada 提交于
Some new boards define CONFIG_SYS_HZ again! Remove. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NBo Shen <voice.shen@atmel.com>
-
- 23 4月, 2014 1 次提交
-
-
由 Shengzhou Liu 提交于
- update readme. - add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315 ucode from NOR/NAND/SPI/SD/REMOTE. - update cpld vbank with SW3[5:7]=000 as default vbank0 instead of previous SW3[5:7]=111 as default vbank. - fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2. Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-