- 07 12月, 2017 1 次提交
-
-
由 Stefan Mavrodiev 提交于
>From revision J the board uses new phy chip LAN8710. Compared with RTL8201, RA17 pin is TXERR. It has pullup which causes phy not to work. To fix this PA17 is muxed with GMAC function. This makes the pin output-low. Signed-off-by: NStefan Mavrodiev <stefan@olimex.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
- 03 12月, 2017 3 次提交
-
-
由 Vasily Khoruzhick 提交于
These are actually different bits, and since some monitors (Benq BL2420PT) have modes with different HSYNC and VSYNC polarity, we should set them independently Tested on Pine64-LTS with Benq BL2420PT monitor. Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: NAnatolij Gustschin <agust@denx.de> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Icenowy Zheng 提交于
Some H5 boards are designed to start at 1.1V CPUx voltage (e.g. Nano Pi NEO2), which may not work properly at 1008MHz if the chip's quality is not so good. Lower the default CPUx frequency of H5 to 816MHz. Signed-off-by: NIcenowy Zheng <icenowy@aosc.io> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Icenowy Zheng 提交于
Add support for setting up SimpleFB for LCD display output in DE2 SimpleFB setup code. Signed-off-by: NIcenowy Zheng <icenowy@aosc.io> Reviewed-by: NJagan Teki <jagan@openedev.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 21 11月, 2017 2 次提交
-
-
由 Antony Antony 提交于
Add initial DT for NanoPi NEO Plus2 by FriendlyARM - Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU - 1 GB DDR3 RAM - 8GB eMMC flash (Samsung KLM8G1WEPD-B031) - micro SD card slot - Gigabit Ethernet (external RTL8211E-VB-CG chip) - 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module) - 2x USB 2.0 host ports Signed-off-by: NAntony Antony <antony@phenome.org> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Antony Antony 提交于
last Kernel commit of sun50i-h5.dtsi d86e63e1f0b7 Signed-off-by: NAntony Antony <antony@phenome.org> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
- 18 11月, 2017 1 次提交
-
-
由 Tom Rini 提交于
We first introduce CONFIG_USE_BOOTCOMMAND, similar to CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex scheme around this usage, and these have been defered for the moment so that platform maintainers can work on a migration plan. Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NLukasz Majewski <lukma@denx.de>
-
- 17 11月, 2017 33 次提交
-
-
由 Dongjin Kim 提交于
Since CONFIG_DEFAULT_CONSOLE is already started with "console=", the console argument in CONFIG_EXTRA_ENV_SETTINGS is expanded to "console=console=ttySAC1,115200n8" and this causes the wrong console device. #define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" ... #define CONFIG_EXTRA_ENV_SETTINGS \ "console=" CONFIG_DEFAULT_CONSOLE Signed-off-by: NDongjin Kim <tobetter@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Landheer-Cieslak, Ronald 提交于
UARTs 1 through 5 were missing in the code - added. Also pick the default according to the configuration setting for the console index. Signed-off-by: NRonald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
-
由 Minghuan Lian 提交于
This patch is to change U-Boot PCI bus assignement compliant with Linux. It means each PCIe controller's bus number is 0, not the current maximum PCI bus number, when start to scan this controller. Signed-off-by: NMinghuan Lian <Minghuan.Lian@nxp.com> Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Gan, Yau Wai 提交于
Tag CPU with dm-pre-reloc to enable driver before relocation. Signed-off-by: NGan, Yau Wai <yau.wai.gan@intel.com> Cc: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: NMarek Vasut <marex@denx.de>
-
由 Adam Ford 提交于
To keep the board file smaller and clean, let's move the pinmux to the header file. Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Jorge Ramirez-Ortiz 提交于
Save the environment data at the end of the boot partition on emmc Signed-off-by: NJorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
-
由 Jorge Ramirez-Ortiz 提交于
Allow the platform to define a partition by name at the end of which the environment data will be located. Signed-off-by: NJorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
-
由 Wilson Lee 提交于
In U-boot, serial_tstc was use to determine is there have a character in serial console that pending for read. If there is no "pending" function implemented in serial driver, the serial-uclass will return "true(1)" to indicate there have a character pending to read. Thus, read a character from nulldev serial will result in continuous getting -EAGAIN return which might lead system to hang. This commit is to fix a bug in nulldev serial which implement "pending" function in nulldev serial to always indicate there is no character in console that pending for read. Signed-off-by: NWilson Lee <wilson.lee@ni.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Keng Soon Cheah <keng.soon.cheah@ni.com> Cc: Chen Yee Chew <chen.yee.chew@ni.com> Cc: Bin Meng <bmeng.cn@gmail.com>
-
由 Kever Yang 提交于
We need to update gd in assamble code after relocate, this is a fix to: adc421e4 arm: move gd handling outside of C code Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Stephen Warren 提交于
This is required in the case where U-Boot is typically loaded and run at a particular address, but for some reason the RAM at that location is not available, e.g. due to memory fragmentation loading other boot binaries or firmware, splitting an SMP complex between various different OSs without using e.g. the EL2 second-stage page tables to hide the memory asignments, or due to known ECC failures. Signed-off-by: NStephen Warren <swarren@nvidia.com>
-
由 Stephen Warren 提交于
It can be useful to record how long tests take; this can help debug slow running test systems or track changes in performance over time. Enhance the test system to record timestamps while running test: - Whenever a new log file section is started. - After U-Boot is started and communication has been established. - After each host or U-Boot command is executed. Signed-off-by: NStephen Warren <swarren@nvidia.com>
-
由 Patrice Chotard 提交于
Fix clock division factor initialization for RCC_PLLCFGR registers. PLLR bits (bit 31-28) in RCC_PLLCFGR must not be cleared, it's a forbidden value. So update RCC_PLLCFGR using clrsetbits_le32() to set only necessary bits fields. Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Patrice Chotard 提交于
Add .getcd callback to check is MMC card is present Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrice Chotard 提交于
Allow to get and enable MMC related clock Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrice Chotard 提交于
Allow to get "bus-width" property from device tree Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrice Chotard 提交于
Convert this driver to driver model. This driver is also used by VEXPRESS platforms which doesn't use driver model. Tested on STM32F746 and STM32F769 platforms. Signed-off-by: NChristophe Priouzeau <christophe.priouzeau@st.com> Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrice Chotard 提交于
Update arm_pl180_mmci_init() prototype by adding struct mmc** param. This is needed before converting this driver to driver model in order to use arm_pl180_mmci_init() in driver model and in none driver model implementation Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Tom Rini 提交于
This option provides better performance and should really always be enabled. Make this be default y. Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJeroen Hofstee <jeroen@myspectrum.nl>
-
由 Neil Armstrong 提交于
This patch adds support for the Internal RMII Ethernet PHY on the Amlogic P212 Reference Board. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers were added to configure the internal RMII PHY interface. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Masahiro Yamada 提交于
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the followings 6 files: fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c fdt_sw.c Make them a wrapper of scripts/dtc/libfdt/*. This is exactly what Linux does to sync libfdt. In order to make is possible, import <linux/libfdt.h> and <linux/libfdt_env.h> from Linux 4.14-rc5. Unfortunately, U-Boot locally modified the following 3 files: fdt_ro.c fdt_wip.c fdt_rw.c The fdt_region.c is U-Boot own file. I did not touch them in order to avoid unpredictable impact. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Add this typedef in the same place as in Linux. This is necessary to refactor libfdt inclusion. U-Boot also defines it in include/compiler.h. Of course it should not do that, but I do not want to open a can of worms. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Prior to this commit, tools/Makefile pulls all libfdt files from lib/libfdt. lib/libfdt/ and scripts/dtc/libfdt have the same copies for the followings 6 files: fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c fdt_sw.c This commit changes them to #include ones from scripts/dtc/libfdt. Unfortunately, U-Boot locally modified the following 3 files: fdt_ro.c fdt_wip.c fdt_rw.c I did not touch them in order to avoid unpredictable impact. The fdt_region.c is U-Boot own file. This is also borrowed from lib/libfdt/. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Fortunately, U-Boot did not modify libfdt_internal.h locally. Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be periodically synced with the upstream DTC (or kernel). Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Fortunately, U-Boot did not modify fdt.h locally. Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be periodically synced with the upstream DTC (or kernel). Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Currently, pylibfdt is always compiled if swig is installed on your machine. It is really annoying because most of targets (excepts x86, sunxi, rockchip) do not use dtoc or binman. "checkbinman" and "checkdtoc" are wrong. It is odd that the final build stage checks if we have built necessary tools. If your platform depends on dtoc/binman, you must be able to build pylibfdt. If swig is not installed, it should fail immediately. I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be property select:ed by platforms that need them. Kbuild will descend into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Masahiro Yamada 提交于
The pylibfdt is used by dtoc (and, indirectly by binman), but there is no reason why it must be generated in the tools/ directory. Recently, U-Boot switched over to the bundled DTC, and the directory structure under scripts/dtc/ now mirrors the upstream DTC project. So, scripts/dtc/pylibfdt is the best location. I also rewrote the Makefile in a cleaner Kbuild style. The scripts from the upstream have been moved as follows: lib/libfdt/pylibfdt/setup.py -> scripts/dtc/pylibfdt/setup.py lib/libfdt/pylibfdt/libfdt.i -> scripts/dtc/pylibfdt/libfdt.i_shipped The .i_shipped is coped to .i during building because the .i must be located in the objtree when we build it out of tree. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
This adds the following commits from upstream: b1a6003 tests: Add a test for overlays syntactic sugar 737b2df overlay: Add syntactic sugar version of overlays 497432f checks: Use proper format modifier for size_t 22a65c5 dtc: Bump version to v1.4.5 c575d80 Add fdtoverlay to .gitignore b6a6f94 fdtoverlay: Sanity check blob size 8c1eb15 pylibfdt: Use Python2 explicitly ee3d26f checks: add interrupts property check c1e7738 checks: add gpio binding properties check b3bbac0 checks: add phandle with arg property checks [ sync with Linux commit: 4201d057ea91c3d6efd2db65219bc91fae413bc2 ] Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Rob Herring 提交于
libfdt has gained some new files. We need to include them in the kernel's copy. Reported-by: NKyle Yan <kyan@codeaurora.org> Signed-off-by: NRob Herring <robh@kernel.org> Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> [ Linux commit: 4322323058f010274564006d61945187a15b6361 ]
-
由 Neil Armstrong 提交于
This adds platform code for the Amlogic P212 reference board based on a Meson GXL (S905X) SoC with the Meson GXL configuration. This initial submission only supports UART and MMC/SDCard, support for the internal Ethernet PHY in Work In Progress. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Reviewed-by: NBeniamino Galvani <b.galvani@gmail.com>
-
由 Neil Armstrong 提交于
Add the Amlogic Meson GXL pinctrl support based on the GXBB driver and the synchronized DTS from Linux 4.13.5 Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Reviewed-by: NBeniamino Galvani <b.galvani@gmail.com>
-
由 Neil Armstrong 提交于
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5 In the preparation of the support of the Amlogic P212 board, import the corresponding meson-gxl-s905x-p212.dts file. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Reviewed-by: NBeniamino Galvani <b.galvani@gmail.com>
-