- 06 2月, 2016 1 次提交
-
-
由 Bin Meng 提交于
Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 04 2月, 2016 7 次提交
-
-
-
-
由 Dinh Nguyen 提交于
Apparently, the logic for the FPGA global bit is not universal between Gen5 and Gen10 devices is not the same. Disabling this bit, while applicable to Gen10 devices, will break FPGA programming on Gen5 devices. Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
-
由 Frank Wang 提交于
In current high speed fastboot, fs_ep_in.wMaxPacketSize is configured 64 bytes as default, as a result, it failed to match the size at initialization stage in usb controller. Actually, hardware can support less than or equal to 512 bytes in high speed mode, so I changed the condition from '!=' to '>' to fix this issue. Signed-off-by: NFrank Wang <frank.wang@rock-chips.com> Tested-by: NSteve Rae <srae@broadcom.com>
-
由 Peng Fan 提交于
Implement board_mmc_get_env_dev for the boards. Following is examples: SD1/SD2/SD3: return devno; SD2/SD3: return devno - 1; SD2/SD4: if (devno == 2), return dev - 2; return dev - 1; Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Implement mmc_get_env_dev, devno can be got from smbr1 of SRC. Introduce a weak function board_mmc_get_env_dev, different boards can implement it according to different sdhc controllers that used by the board. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Peng Fan 提交于
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to match the one in common/env_mmc.c. Introduce a weak function board_mmc_get_env_dev. Different boards can implement this according to sdhc controller which is used by the board. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
- 03 2月, 2016 23 次提交
-
-
由 Bhuvanchandra DV 提交于
All boards using this driver are with device tree support, hence drop the legacy code in driver to have a pure DT solution. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bhuvanchandra DV 提交于
All boards using this driver are with device tree support, hence drop the legacy code in driver to have a pure DT solution. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bhuvanchandra DV 提交于
Remove the legacy way of enabling GPIO, SPI and UART on Vybrid based boards since these driver's now only supports DT mode. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: NStefan Agner <stefan.agner@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bhuvanchandra DV 提交于
Let's go with pure DT solution for board's based on NXP/Freescale Vybrid platform. - Merge the DT defconfig with non-DT defconfig for Toradex Colibri VF50/VF61 and drop the non-DT defconfig. - Update the legacy defconfigs for NXP/Freescale VF610 Tower Board with DT. - Update the legacy defconfigs for Phytec phyCORE-vybrid Board with DT. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: NStefan Agner <stefan.agner@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bhuvanchandra DV 提交于
- Add device tree files for Phytec phyCORE-Vybrid Board. - Enable lpuart support for Phytec phyCORE-Vybrid Board. - Use UART1 for stdout. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bhuvanchandra DV 提交于
- Add device tree files for NXP/Freescale VF610 Tower Board. - Enable lpuart support on NXP/Freescale VF610 Tower Board. - Use UART1 as stdout. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bhuvanchandra DV 提交于
- Enable lpuart support on Toradex Colibri VF50/VF61 - Use UART0 for stdout. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bhuvanchandra DV 提交于
Since SPDX license is already there, drop the full one. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: NStefan Agner <stefan.agner@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bhuvanchandra DV 提交于
Add device tree node's for lpuart on Vybrid platform Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: NStefan Agner <stefan.agner@toradex.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Ye Li 提交于
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1 port, enable this display feature by adding relevant BSP codes and configurations. Signed-off-by: NYe Li <ye.li@nxp.com>
-
由 Ye Li 提交于
The checking with max frequency supported is not correct, because the temp is calculated by max pre and post dividers. We can decrease any divider to meet the max frequency limitation. Actually, the calculation below the codes is doing this way to find best pre and post dividers. Signed-off-by: NYe Li <ye.li@nxp.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Ye Li 提交于
Wrong checking for the base_addr paramter with LCDIF1 and LCDIF2. Always enter the -EINVAL return. Signed-off-by: NYe Li <ye.li@nxp.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
As mx6slevk has only one Ethernet port, we don't need to declare CONFIG_ETHPRIME, so just remove it. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Ye Li 提交于
The BOOTCFG value used by bmode for SABRESD eMMC boot are actually for SD card. Fixed the value to correct one. Signed-off-by: NYe Li <ye.li@nxp.com> Signed-off-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NStefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested by the LAN8720 datasheet. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
Since commit 59370f3f ("net: phy: delay only if reset handler is registered") Ethernet is no longer functional. This commit does not have an issue in itself, but it revelead a problem with the Ethernet initialization. According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested in order to have Ethernet working again. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Ye Li 提交于
Initial version for mx6sx SABREAUTO board support with features: PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander. Signed-off-by: NYe Li <ye.li@nxp.com>
-
由 Ye Li 提交于
The i.MX6SX and i.MX6UL has two ENET controllers, add support for reading MAC address from fuse for ENET2. Signed-off-by: NYe Li <ye.li@nxp.com>
-
由 Bin Meng 提交于
Currently when building mxsboot on certain machines it reports: HOSTCC tools/mxsboot tools/mxsboot.c: In function 'mx28_create_sd_image': tools/mxsboot.c:560: warning: implicit declaration of function 'htole32' /tmp/cchLIV6q.o: In function 'main': mxsboot.c:(.text+0x6d8): undefined reference to 'htole32' mxsboot.c:(.text+0x6e7): undefined reference to 'htole32' mxsboot.c:(.text+0x6f6): undefined reference to 'htole32' mxsboot.c:(.text+0x705): undefined reference to 'htole32' mxsboot.c:(.text+0x711): undefined reference to 'htole32' /tmp/cchLIV6q.o:mxsboot.c:(.text+0x71d): more undefined references to 'htole32' follow collect2: ld returned 1 exit status make[1]: *** [tools/mxsboot] Error 1 make: *** [tools] Error 2 The solution is to use cpu_to_le32() instead which is more portable, just like other U-Boot tools [1] do. [1] http://lists.denx.de/pipermail/u-boot/2014-October/192919.htmlSuggested-by: NMarek Vasut <marex@denx.de> Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Peter Robinson 提交于
All boards that support PXE booting use the pxefile_addr_r variable. Standardise wandboard with this variable as pxe_addr_r isn't used anywhere else so it's a typo. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Acked-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Marek Vasut 提交于
Enable the DDR calibration functionality on Novena to deal with the memory SoDIMM on this board. Moreover, tweak the initial DDR DRAM parameters so the calibration works properly. Signed-off-by: NMarek Vasut <marex@denx.de>
-
由 Marek Vasut 提交于
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code fine-tunes the behavior of the MMDC controller in order to improve the signal integrity and memory stability. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 02 2月, 2016 9 次提交
-
-
-
-
由 Wenyou Yang 提交于
The sama5d2 Xplained SPL supports the boot medias: spi flash and SD Card. Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Wenyou Yang 提交于
To remove the unnecessary #ifdef-endif, use the mpddrc IP version to check whether or not the interleaved decoding type is supported. Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Wenyou Yang 提交于
The DDR3-SDRAM initialization sequence is implemented in accordance with the DDR3-SRAM/DDR3L-SDRAM initialization section described in the SAMA5D2 datasheet. Add registers and definitions of mpddrc controller, which is used to support DDR3 devices. Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Wenyou Yang 提交于
Add struct atmel_mpddrc_config to accommodate the mpddrc register configurations, not using the mpddrc register map structure, struct atmel_mpddrc, in order to increase readability and reduce run-time memory use. Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Josh Wu 提交于
Also if minimum ecc requirment is bigger then what we support, then just use our maxium pmecc support. But it is not safe, so we'll output a warning about this. Signed-off-by: NJosh Wu <josh.wu@atmel.com> Acked-by: NScott Wood <scottwood@freescale.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Josh Wu 提交于
1. add the pmecc register mapping for sama5d2. 2. add the pmecc error location register mapping for sama5d2. 3. add some new field that is different from old ip. 4. add sama5d2 pmecc ip version number. Signed-off-by: NJosh Wu <josh.wu@atmel.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Simon Glass 提交于
When OF_CONTROL is enabled, u-boot-dtb.* files are the same as u-boot.* files. So we can use the latter for simplicity. Tested-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NSimon Glass <sjg@chromium.org>
-