- 19 10月, 2009 6 次提交
-
-
由 Sandeep Paulraj 提交于
This patch removes dependency on the sizes.h header file and removes all references to SZ_xx. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
Update default environment to support new kernel DSS2 subsystem and simplify rootfs type and location changes. Signed-off-by: NSteve Sakoman <sakoman@gmail.com> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Sandeep Paulraj 提交于
This patch adds support for the leopard board which is based on the DM355 SOC. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch adds the initial support for DM6467 EVM. Other features like NET and NAND support will be added as follow up patches. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Eric Benard 提交于
This change fixes the compiler warning main.c: In function 'abortboot': main.c:122: warning: too few arguments for format Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Eric Benard 提交于
This change fixes the compiler warning nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output! Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 14 10月, 2009 2 次提交
-
-
This sets CONFIG_SYS_HZ to 1000 for all boards that use the s3c2400 and s3c2410 cpu's which fixes various problems such as the timeouts in tftp being too short. Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have any s3c2400 or s3c2410 boards but need this patch applying before I can submit patches for the SBC2440-II Board. Also, ran MAKEALL for all ARM9 targets and no new warnings or errors were found. It was originally submitted on 21/06/2009 but didn't get into the 2009.08 release, and Jean-Pierre made one comment on the original patch (see http://lists.denx.de/pipermail/u-boot/2009-July/055470.html). I've made two changes to the original patch: - it's been re-based to the current release - I've re-named get_timer_raw() to get_ticks() in response to Jean-Pierre's comment This affects the sbc2410, smdk2400, smdk2410 and trab boards. I've copied it directly to the maintainers of all except the sbc2410 which doesn't have an entry in MAINTAINERS. Signed-off-by: NKevin Morfitt <kmorfitt@aselaptop-1.localdomain> Tested-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Minkyu Kang 提交于
Adds new board SMDKC100 that uses s5pc100 SoC Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Signed-off-by: NHeungJun, Kim <riverful.kim@samsung.com>
-
- 13 10月, 2009 10 次提交
-
-
由 Daniel Gorsulowski 提交于
This patch implements several updates: -disable CONFIG_ENV_OVERWRITE -add new hardware style variants and set the arch numbers appropriate -pass the serial# and hardware revision to the kernel -removed unused macros from include/configs/meesc.h -fixed multiline comment style Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
-
由 Olof Johansson 提交于
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded over tftp. This also refactors the smc911x driver to allow for detecting when the chip is missing. I.e. the detect_chip() function is called earlier and will abort gracefully when the Chip ID read returns all 1's. Signed-off-by: NOlof Johansson <olof@lixom.net> Acked-by: NDirk Behme <dirk.behme@googlemail.com> Acked-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Tom Rix 提交于
This changes fixes an early i2c error. It appears that I2C is working because once a read or write error is detected, the omap24xx_i2c driver calls i2c_init inside its error handling check. While it is ok to attempt error handling this way, the boards must not depend on this side effect to initialize it's i2c. Instead of explicitly calling i2c_init for every board, use the generic arm initialization in lib_arm/board.c. By defining the config variable CONFIG_HARD_I2C, the omap3 i2c initialization is included in the init_sequence table. Run tested on Beagle. Compile tested on the omap3's Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Simon Kagstrom 提交于
The implementation is borrowed from the sheevaplug board and the Marvell 1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA. Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
-
由 Tom Rix 提交于
these boards are built around Atmel's AT91SAM9260/9G20 and have up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND and include a 10/100 Ethernet PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Tom Rix 提交于
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Sandeep Paulraj 提交于
The DM365 config was using the 'CONFIG_CMD_SAVEENV' flag. This is already included when we include the config_cmd_default.h header file. So this flag is removed. Also another flag to enable NAND functions was being enabled incorrectly. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch does the following 1) Enables the NAND driver which is now available. 2) Enables the 'CONFIG_MTD_DEVICE' as without this the compilation will fail 3) We now have a safe place to store environment and defines an offset where this can be stored. This offset value is such that it is after the location where U-Boot is flashed using TI flash utilities. 4) Enables Bootdelay 5) Increases malloc() arena size. Manufacturers are coming out with NAND with large blocks sizes of upto 1 MiB. It has been noticed that as the block size of the NAND used is increased, if this particular value is not increased, the NAND driver will output out of memory errors. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
The Default mode that is built for the Davinci DVEVM happens to be the NOR mode. When we want to build for the NAND mode, we get a compilation error. This is overcome by defining the CONFIG_MTD_DEVICE flag in the NAND mode. The image built for NAND mode was successfully tested on the DaVinci DM6446 EVM. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch removes the asm/sizes.h header file from being included in the DaVinci SOC configs. References to SZ_xx have been replaced by appropriate bit shifted values. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com> Acked-by: NWolfgang Denk <wd@denx.de>
-
- 11 10月, 2009 1 次提交
-
-
由 Luigi 'Comio' Mantellini 提交于
Signed-off-by: NLuigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 08 10月, 2009 1 次提交
-
-
由 Detlev Zundel 提交于
This fixes the code and the comment according to the original intent of doing an intensive memory test when PSC6_3 is pulled low on the STK52xx. Notably PORT_CONFIG will be overridden with this correct code now, so beware. The original code only worked by coincidence depending on the PORT_CONFIG setting from the header file. The new code was tested to ensure that the (undocumented) memory test still works on the STK52x. Signed-off-by: NDetlev Zundel <dzu@denx.de> CC: Martin Krause <Martin.Krause@tqs.de> Minor white-space cleanup. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 05 10月, 2009 1 次提交
-
-
由 Ben Warren 提交于
All in-tree boards that use this controller have CONFIG_NET_MULTI added Also: - changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111 - cleaned up line lengths - modified all boards that override weak function in this driver - modified all eeprom standalone apps to work with new driver - updated blackfin standalone EEPROM app after testing Signed-off-by: NBen Warren <biggerbadderben@gmail.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 03 10月, 2009 3 次提交
-
-
由 Peter Tyser 提交于
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
由 Peter Tyser 提交于
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
由 Peter Tyser 提交于
The following changes allow U-Boot to fully relocate from flash to RAM: - Remove linker scripts' .fixup sections from the .text section - Add -mrelocatable to PLATFORM_RELFLAGS for all boards - Define CONFIG_RELOC_FIXUP_WORKS for all boards Previously, U-Boot would partially relocate, but statically initialized pointers needed to be manually relocated. Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
- 02 10月, 2009 1 次提交
-
-
由 Matthias Fuchs 提交于
This patch adds support to detect the amount of DDR2 SDRAM on PMC440 modules. Detection is done by probing through a list of available and supported hardware configurations from 1GByte down to 256MB. The static TLB entry is replaced by dynamically created entries. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 01 10月, 2009 2 次提交
-
-
由 Mike Frysinger 提交于
The Linux kernel has changed the way it numbers serial ports, so update the default command line to match it. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
The u-boot image has outgrown the current space and overflowed into the env sector. So move the env to the next available sector (we've already allocated the first few sectors anyways for u-boot). Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 30 9月, 2009 4 次提交
-
-
由 Mingkai Hu 提交于
The MPC8536E is capable of booting from the on-chip ROM - boot from eSDHC and boot from eSPI. When power on, the porcessor excutes the ROM code to initialize the eSPI/eSDHC controller, and loads the mian U-Boot image from the memory device that interfaced to the controller, such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or L2SRAM, then boot from it. The memory device should contain a specific data structure with control word and config word at the fixed address. The config word direct the process how to config the memory device, and the control word direct the processor where to find the image on the memory device, or where copy the main image to. The user can use any method to store the data structure to the memory device, only if store it on the assigned address. The on-chip ROM code will map the whole 4GB address space by setting entry0 in the TLB1, so the main image need to switch to Address space 1 to disable this mapping and map the address space again. This patch implements loading the mian U-Boot image into L2SRAM, so the image can configure the system memory by using SPD EEPROM. Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Mingkai Hu 提交于
MPC8536E can support booting from NAND flash which uses the image u-boot-nand.bin. This image contains two parts: a 4K NAND loader and a main U-Boot image. The former is appended to the latter to produce u-boot-nand.bin. The 4K NAND loader includes the corresponding nand_spl directory, along with the code twisted by CONFIG_NAND_SPL. The main U-Boot image just like a general U-Boot image except the parts that included by CONFIG_SYS_RAMBOOT. When power on, eLBC will automatically load from bank 0 the 4K NAND loader into the FCM buffer RAM where CPU can execute the boot code directly. In the first stage, the NAND loader copies itself to RAM or L2SRAM to free up the FCM buffer RAM, then loads the main image from NAND flash to RAM or L2SRAM and boot from it. This patch implements the NAND loader to load the main image into L2SRAM, so the main image can configure the RAM by using SPD EEPROM. In the first stage, the NAND loader copies itself to the second to last 4K address space, and uses the last 4K address space as the initial RAM for stack. Obviously, the size of L2SRAM shouldn't be less than the size of the image used. If so, the workaround is to generate another image that includes the code to configure the RAM by SPD and load it to L2SRAM first, then relocate the main image to RAM to boot up. Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Mingkai Hu 提交于
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Paul Gortmaker 提交于
By nature of being based off the MPC8548CDS board, this board inherited an ENV_SIZE setting of 256k. But since it has a smaller flash device (8MB soldered on), it has a native sector size of 128k, and hence the ENV_SIZE was causing 2 sectors to be used for the environment. By removing the unused sector, we can push TEXT_BASE up closer to the end of address space and reclaim that sector for any other application. This also fixes the mismatch between TEXT_BASE and MONITOR_LEN reported by Kumar earlier. Since this board also supports the ability to boot off the 64MB SODIMM flash, this change is forward looking with that in mind; i.e. the settings for MONITOR_LEN and ENV_SIZE will work when the 512k sectors of the SODIMM flash are used for alternate boot in the future. Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 27 9月, 2009 1 次提交
-
-
由 Kim Phillips 提交于
some LCRR bits are not documented throughout the 83xx family RMs. New board porters copying similar board configurations might omit setting e.g., DBYP since it was not documented in their SoC's RM. Prevent them bricking their board by retaining power on reset values in bit fields that the board porter doesn't explicitly configure via CONFIG_SYS_<registername>_<bitfield> assignments in the board config file. also move LCRR assignment to cpu_init_r[am] to help ensure no transactions are being executed via the local bus while CLKDIV is being modified. also start to use i/o accessors. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 26 9月, 2009 3 次提交
-
-
由 Paul Gortmaker 提交于
Commit 804d83a5 allows us to move all the configuration variation tweaks out of the top level Makefile and down into the board config header. This takes advantage of that for the sbc8349 board. Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Anton Vorontsov 提交于
With this patch we can change QE USB mode without need to hand-edit the device tree. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Anton Vorontsov 提交于
This patch fixes various ethernet issues with gigabit links handling in U-Boot. The workarounds originally implemented by Kim Phillips for Linux kernel. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 25 9月, 2009 5 次提交
-
-
由 Heiko Schocher 提交于
U-Boot can detect if an IDE device is present or not. If not, and this new config option is activated, U-Boot removes the ATA node from the DTS before booting Linux, so the Linux IDE driver does not probe the device and crash. This is needed for buggy hardware (uc101) where no pull down resistor is connected to the signal IDE5V_DD7. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
- As these boards are similiar, collect common config options in manroland/common.h and manroland/mpc52xx-common.h for mpc5200 specific common options for this manufacturer. - add OF support - update default environment Signed-off-by: NHeiko Schocher <hs@denx.de> Minor edit of commit message. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Martha M Stan 提交于
Signed-off-by: NMartha M Stan <mmarx@silicontkx.com> Minor coding style cleanup. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Martha M Stan 提交于
Signed-off-by: NMartha M Stan <mmarx@silicontkx.com> Minor cleanup: Re-ordered default_mddrc_config[] to have matching indices. This allows to use the same index "N" for source and target fields; before, we had code like this out_be32(&im->mddrc.ddr_time_config2, mddrc_config[3]); which always looked like a copy & paste error because 2 != 3. Also, use NULL when meaning a null pointer. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Paul Gortmaker 提交于
Commit 804d83a5 allows us to move all the configuration variation tweaks out of the top level Makefile and down into the boards config header. This takes advantage of that for the sbc8540/sbc8560 boards. There were a couple of cheezy comments pointing at incorrect files, or files that don't exist, so I've cleaned those up too. Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-