- 19 10月, 2009 6 次提交
-
-
由 Sandeep Paulraj 提交于
This patch removes dependency on the sizes.h header file and removes all references to SZ_xx. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
Update default environment to support new kernel DSS2 subsystem and simplify rootfs type and location changes. Signed-off-by: NSteve Sakoman <sakoman@gmail.com> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Sandeep Paulraj 提交于
This patch adds support for the leopard board which is based on the DM355 SOC. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch adds the initial support for DM6467 EVM. Other features like NET and NAND support will be added as follow up patches. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Eric Benard 提交于
This change fixes the compiler warning main.c: In function 'abortboot': main.c:122: warning: too few arguments for format Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Eric Benard 提交于
This change fixes the compiler warning nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output! Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 14 10月, 2009 6 次提交
-
-
This patch re-formats the arm920t s3c24x0 header files in preparation for changes to add support for the Embest SBC2440-II Board. The changes are as follows: - re-indent the code using Lindent - make sure register layouts are defined using a C struct - replace the upper-case typedef'ed C struct names with lower case non-typedef'ed ones - make sure registers are accessed using the proper accessor functions - run checkpatch.pl and fix any error reports It assumes the following patch has been applied first: - [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009 - patch 1/4 of this series Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have any s3c2400 or s3c2410 boards but need this patch applying before I can submit patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400, smdk2410 and trab configs to use the mtd nand driver (which isn't used by any board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or errors were found. Signed-off-by: NKevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
This sets CONFIG_SYS_HZ to 1000 for all boards that use the s3c2400 and s3c2410 cpu's which fixes various problems such as the timeouts in tftp being too short. Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have any s3c2400 or s3c2410 boards but need this patch applying before I can submit patches for the SBC2440-II Board. Also, ran MAKEALL for all ARM9 targets and no new warnings or errors were found. It was originally submitted on 21/06/2009 but didn't get into the 2009.08 release, and Jean-Pierre made one comment on the original patch (see http://lists.denx.de/pipermail/u-boot/2009-July/055470.html). I've made two changes to the original patch: - it's been re-based to the current release - I've re-named get_timer_raw() to get_ticks() in response to Jean-Pierre's comment This affects the sbc2410, smdk2400, smdk2410 and trab boards. I've copied it directly to the maintainers of all except the sbc2410 which doesn't have an entry in MAINTAINERS. Signed-off-by: NKevin Morfitt <kmorfitt@aselaptop-1.localdomain> Tested-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Minkyu Kang 提交于
Adds new board SMDKC100 that uses s5pc100 SoC Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Signed-off-by: NHeungJun, Kim <riverful.kim@samsung.com>
-
由 Minkyu Kang 提交于
This patch includes the serial driver for s5pc1xx. s5pc1xx uart driver needs own register setting and clock configuration. So, need to special driver. Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Minkyu Kang 提交于
This patch includes the onenand driver for s5pc100 Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Minkyu Kang 提交于
This patch adds support for the Samsung s5pc100 and s5pc110 SoCs. The s5pc1xx SoC is an ARM Cortex A8 processor. Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Signed-off-by: NHeungJun, Kim <riverful.kim@samsung.com>
-
- 13 10月, 2009 15 次提交
-
-
由 Daniel Gorsulowski 提交于
This patch implements several updates: -disable CONFIG_ENV_OVERWRITE -add new hardware style variants and set the arch numbers appropriate -pass the serial# and hardware revision to the kernel -removed unused macros from include/configs/meesc.h -fixed multiline comment style Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
-
由 Olof Johansson 提交于
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded over tftp. This also refactors the smc911x driver to allow for detecting when the chip is missing. I.e. the detect_chip() function is called earlier and will abort gracefully when the Chip ID read returns all 1's. Signed-off-by: NOlof Johansson <olof@lixom.net> Acked-by: NDirk Behme <dirk.behme@googlemail.com> Acked-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Tom Rix 提交于
This changes fixes an early i2c error. It appears that I2C is working because once a read or write error is detected, the omap24xx_i2c driver calls i2c_init inside its error handling check. While it is ok to attempt error handling this way, the boards must not depend on this side effect to initialize it's i2c. Instead of explicitly calling i2c_init for every board, use the generic arm initialization in lib_arm/board.c. By defining the config variable CONFIG_HARD_I2C, the omap3 i2c initialization is included in the init_sequence table. Run tested on Beagle. Compile tested on the omap3's Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Sandeep Paulraj 提交于
Some DaVinci SOC's use GPIOs to enable EMAC and DM9000. This patch adds some definitions for GPIO registers and also adds structures for GPIO. A separate header file is being added so that in future we can have a DaVinci GPIO driver similer to OMAP. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com> Acked-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Sandeep Paulraj 提交于
In the DaVinci specific code, we use both CONFIG_SOC_DM646X and CONFIG_SOC_DM646x to represent DM646x specific code. This patch changes occurrences of CONFIG_SOC_DM646x to CONFIG_SOC_DM646X. This is because for DM644x series of SOCs we use the flag CONFIG_SOC_DM644X. We want some uniformity. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com> Acked-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Dirk Behme 提交于
Fix warning Dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: NDirk Behme <dirk.behme@googlemail.com> CC: Steve Sakoman <sakoman@gmail.com> Acked-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Simon Kagstrom 提交于
The implementation is borrowed from the sheevaplug board and the Marvell 1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA. Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
-
由 Tom Rix 提交于
these boards are built around Atmel's AT91SAM9260/9G20 and have up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND and include a 10/100 Ethernet PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Tom Rix 提交于
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Sandeep Paulraj 提交于
The DM365 config was using the 'CONFIG_CMD_SAVEENV' flag. This is already included when we include the config_cmd_default.h header file. So this flag is removed. Also another flag to enable NAND functions was being enabled incorrectly. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch does the following 1) Enables the NAND driver which is now available. 2) Enables the 'CONFIG_MTD_DEVICE' as without this the compilation will fail 3) We now have a safe place to store environment and defines an offset where this can be stored. This offset value is such that it is after the location where U-Boot is flashed using TI flash utilities. 4) Enables Bootdelay 5) Increases malloc() arena size. Manufacturers are coming out with NAND with large blocks sizes of upto 1 MiB. It has been noticed that as the block size of the NAND used is increased, if this particular value is not increased, the NAND driver will output out of memory errors. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
DM646x is an SOC from TI which has both an ARM and a DSP. There are multiple variants of the SOC mainly dealing with different core speeds. This patch adds the initial framework for the DM646x SOC. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
The Default mode that is built for the Davinci DVEVM happens to be the NOR mode. When we want to build for the NAND mode, we get a compilation error. This is overcome by defining the CONFIG_MTD_DEVICE flag in the NAND mode. The image built for NAND mode was successfully tested on the DaVinci DM6446 EVM. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Tom Rix 提交于
v7_flush_dcache_all, because it depends on omap ROM code is not generic. Rename the function to 'invalidate_dcache' and move it to the omap cpu directory. Collect the other omap cache routines l2_cache_enable and l2_cache_disable with invalide_dcache into cache.S. This means removing the old cache.c file that contained l2_cache_enable and l2_cache_disable. The conversion from cache.c to cache.S was done most through disassembling the uboot binary. The only significant change was to change the comparision for the return of get_cpu_rev from cmp r0, #0 beq earlier_than_label Which was lost information to cmp r0, #CPU_3XX_ES20 blt earlier_than_label The paths through the enable routine were verified by adding an infinite loop and seeing the hang. Then removing the infinite loop and seeing it continue. The disable routine is similar enough that it was not tested with this method. Run tested by cold booting from nand on beagle and zoom1. Compile tested on MAKEALL arm. Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Sandeep Paulraj 提交于
This patch removes the asm/sizes.h header file from being included in the DaVinci SOC configs. References to SZ_xx have been replaced by appropriate bit shifted values. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com> Acked-by: NWolfgang Denk <wd@denx.de>
-
- 11 10月, 2009 2 次提交
-
-
由 Luigi 'Comio' Mantellini 提交于
Signed-off-by: NLuigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Luigi 'Comio' Mantellini 提交于
Rewrite the miiphybb (Bit-banged MII bus driver) in order to support an arbitrary number of mii buses. This feature is useful when your board uses different mii buses for different phys and all (or a part) of these buses are implemented via bit-banging mode. The driver requires that the following macros should be defined into the board configuration file: CONFIG_BITBANGMII - Enable the miiphybb driver CONFIG_BITBANGMII_MULTI - Enable the multi bus support If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs to define at least the following macros: MII_INIT - Generic code to enable the MII bus (optional) MDIO_DECLARE - Declaration needed to access to the MDIO pin (optional) MDIO_ACTIVE - Activate the MDIO pin as out pin MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin MDIO_READ - Read the MDIO pin MDIO(v) - Write v on the MDIO pin MDC_DECLARE - Declaration needed to access to the MDC pin (optional) MDC(v) - Write v on the MDC pin The previous macros make the driver compatible with the previous version (that didn't support the multi-bus). When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill the bb_miiphy_buses[] array with a record for each required bus and declare the bb_miiphy_buses_num variable with the number of mii buses. The record (struct bb_miiphy_bus) has the following fields/callbacks (see miiphy.h for details): char name[] - The symbolic name that must be equal to the MII bus registered name int (*init)() - Initialization function called at startup time (just before the Ethernet initialization) int (*mdio_active)() - Activate the MDIO pin as output int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin int (*set_mdio)() - Write the MDIO pin int (*get_mdio)() - Read the MDIO pin int (*set_mdc)() - Write the MDC pin int (*delay)() - Delay function void *priv - Private data used by board specific code The board code will look like: struct bb_miiphy_bus bb_miiphy_buses[] = { { .name = miibus#1, .init = b1_init, .mdio_active = b1_mdio_active, ... }, { .name = miibus#2, .init = b2_init, .mdio_active = b2_mdio_active, ... }, ... int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) / sizeof(bb_miiphy_buses[0]); Signed-off-by: NLuigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 08 10月, 2009 2 次提交
-
-
由 Detlev Zundel 提交于
This fixes the code and the comment according to the original intent of doing an intensive memory test when PSC6_3 is pulled low on the STK52xx. Notably PORT_CONFIG will be overridden with this correct code now, so beware. The original code only worked by coincidence depending on the PORT_CONFIG setting from the header file. The new code was tested to ensure that the (undocumented) memory test still works on the STK52x. Signed-off-by: NDetlev Zundel <dzu@denx.de> CC: Martin Krause <Martin.Krause@tqs.de> Minor white-space cleanup. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Commit 054197ba and later fixes used an array to initialize some of the MDDRC parameters; however, the use of an array turned out to be a bad idea as it was not possible to correlate structure entries to array indices in readable and reliable way. Now we use a struct instead, which makes this self-explanatory. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 07 10月, 2009 3 次提交
-
-
由 Niklaus Giger 提交于
After running checkstyle.pl on the three previous patches I noted that in the *.h files there were a lot of long lines. This patch solves this problem. Signed-off-by: NNiklaus Giger <niklaus.giger@member.fsf.org> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Niklaus Giger 提交于
Here you find all the changes in the include directory for new register names and adapting other ones to the names used by AMCC in their manuals, e.g. For 440EPx/GRPPC440EPx/GRX, Revision 1.15 – September 22, 2008 For PPC405GP Embedded Processor, Revision 1.02 – March 22, 2006 Signed-off-by: NNiklaus Giger <niklaus.giger@member.fsf.org> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Unfortunately some Rev D PPC405EX/405EXr PVR's are identical with older 405EX(r) parts. Here a list: 0x12911475 - 405EX Rev D with Security *and* 405EX Rev A/B witout Sec 0x12911473 - 405EX Rev D without Security *and* 405EXr Rev A/B with Sec Since there are only a few older parts in the field, this patch now changes the PVR's above to represent the new Rev D versions. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Phong Vo" <pvo@amcc.com>
-
- 05 10月, 2009 2 次提交
-
-
由 Ben Warren 提交于
All in-tree boards that use this controller have CONFIG_NET_MULTI added Also: - changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111 - cleaned up line lengths - modified all boards that override weak function in this driver - modified all eeprom standalone apps to work with new driver - updated blackfin standalone EEPROM app after testing Signed-off-by: NBen Warren <biggerbadderben@gmail.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
The random_port() is meant to be used by other net code, but without a prototype, we get fun warnings like: dns.c: In function 'DnsSend': dns.c:89: warning: implicit declaration of function 'random_port' Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 03 10月, 2009 4 次提交
-
-
由 Peter Tyser 提交于
Now that proper relocation is supported, the reloc_off field is no longer necessary. Note that the location of the standalone application jump table pointer in the global data structure is affected by this change, breaking execution of standalone applications compiled for previous versions of U-Boot. We therefore increment XF_VERSION to 6 Signed-off-by: NPeter Tyser <ptyser@xes-inc.com> Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Peter Tyser 提交于
These architectures don't need relocation fixups, so reduce their codesize a bit by defining CONFIG_RELOC_FIXUP_WORKS. Also remove the reloc_off field from their global data structures as it is no longer needed. Note that the location of the standalone application jump table pointer in the global data structure is affected by this change, breaking execution of standalone applications compiled for previous versions of U-Boot. We will therefore increment XF_VERSION in the next commit, which also touches this area. Signed-off-by: NPeter Tyser <ptyser@xes-inc.com> Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Peter Tyser 提交于
Add #ifdefs where necessary to not perform relocation fixups. This allows boards/architectures which support relocation to trim a decent chunk of code. Note that this patch doesn't add #ifdefs to architecture-specific code which does not support relocation. Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
由 Peter Tyser 提交于
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-