Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPeter Pearse <peter.pearse@arm.com>

this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The PM9261 board is based on the AT91SAM9261-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The way the ALL variable is used allows for config.mk's to add more
targets themselves without having to clutter up the top level Makefile.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

All the Blackfin linker scripts were duplicated across the board dirs with
no difference save from the semi-often used ENV_IS_EMBEDDED option.  So
unify all of them in the lib_blackfin/ dir and for the few boards that
need to embedded the environment directly, add a LDS_BOARD_TEXT define for
them to customize via their board config file.  This is much simpler than
forcing them to duplicate the rest of the linker script.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NHoan Hoang <hnhoan@i-syst.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

For the most part, the Blackfin processor boots files in the LDR format
rather than binary/ELF files.  So we want to export the environment as a
raw blob to the LDR utility so it can embed it at the right location.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The $(SUBDIRS) variable is only declared when U-Boot has been configured,
but it gets used all the time.  In the non-configured case, it is used to
generate a helpful error message, but it needs to be set properly for that
to occur.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Update CHANGELOG, fix minor coding stylke issue. Update Makefile.
Signed-off-by: NWolfgang Denk <wd@denx.de>

The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: NSrikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: NTravis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

MECP5123 is a MPC5121E based module by esd gmbh.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>

ARIA is a MPC5121E based COM Express module by Dave/DENX.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>

We rename the board so we use a consistent name in U-Boot and in
Linux.  Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>

The kernel stores address<->symbol names in it so things can be decoded at
runtime.  Do it in U-Boot, and we get nice symbol decoding when crashing.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Initial U-Boot support for the DaVinci DM355 EVM.  This is a board
from Spectrum Digital.  Board docs include schematic and firmware
for its microcontroller:

  http://c6000.spectrumdigital.com/evmdm355/revd/

Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:

  http://focus.ti.com/docs/prod/folders/print/tms320dm355.html

This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART).  In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>

Zoom2 is a new board from Texas Instruments and LogicPD

The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com

This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp

This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.

To configure, run
make omap3_zoom2_config
Signed-off-by: NTom Rix <Tom.Rix@windriver.com>

This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").

Here the commands to load and start this image from the BDI2000:

440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000

Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.
Signed-off-by: NStefan Roese <sr@denx.de>

Update CHANGELOG
Signed-off-by: NWolfgang Denk <wd@denx.de>

Update CHANGELOG.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Update CHANGELOG.
Signed-off-by: NWolfgang Denk <wd@denx.de>

lowlevel_init.S is not used any more so remove it.
As consequence, we also don't have to generate u-boot.lds
but can use a static version as before.

This also fixes the out-of-tree build problem introduced
with commit f0a2c7b4 "at91: add support for the PM9263 board"
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NWolfgang Denk <wd@denx.de>

The PM9263 board is based on the AT91SAM9263-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

move to linux usb driver organisation

as following

drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NRemy Bohmer <linux@bohmer.net>

Fix out-of-tree build of the imx31_phycore_eet target.
Reported-by: NWolfgang Denk <wd@denx.de>
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>

The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507

with
	- NOR (cfi driver)
	- DataFlash
	- USB OHCI
	- Net
	- I2C (hard)
Signed-off-by: NUlf Samuelsson <ulf@atmel.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>

Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>

This change makes the process of symlinking libfdt_internal.h
unnecessary
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>

crc32.c uses the zlib.h header in include/u-boot/zlib.h.  The symlink
was previously necessary to give U-Boot's version of zlib.h precedence
over the host computer's version of zlib.h.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>