Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NHeungJun, Kim <riverful.kim@samsung.com>
CC: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.

Without this patch, EMIF configurations made in board_init()
will be invalidated.
Signed-off-by: NThomas Lange <thomas@corelatus.se>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Peter Pearse <peter.pearse@arm.com>

Kirkwood family controllers are highly integrated SOCs
based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.

SOC versions supported:-
1) 88F6281-A0       define CONFIG_KW88F6281_A0
2) 88F6192-A0       define CONFIG_KW88F6192_A0

Other supported features:-
1) get_random_hex() fucntion
2) PCI Express port initialization
3) NS16550 driver support

Contributors:
Yotam Admon <yotam@marvell.com>
Michael Blostein <michaelbl@marvell.com
Reviewed-by: NRonen Shitrit <rshitrit@marvell.com>
Acked-by: NStefan Rose <sr@denx.de>
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

This patch is required for Kirkwood SoC support
may be used by other ARM architectures
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Signed-off-by: NMatthias Ludwig <mludwig@ultratronik.de>

On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was
set to 0 after being set to 500 ms for the PHY reset.
Do backup the old reset length and restore it after the MACB initialisation.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NStelian Pop <stelian@popies.net>

This patch adds a SPI driver for the Marvell Kirkwood SoC's.
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Because of the reset_cpu is soc specific, should be move to soc
And read reset value from SYS_ID register instead of hard code
this patch also supports s3c6410
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPeter Pearse <peter.pearse@arm.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPeter Pearse <peter.pearse@arm.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPeter Pearse <peter.pearse@arm.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPeter Pearse <peter.pearse@arm.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPeter Pearse <peter.pearse@arm.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NPeter Pearse <peter.pearse@arm.com>

Signed-off-by: NIlya Yanok <yanok@emcraft.com>

UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>

This patch adds generic code to support Freescale's i.MX27 SoCs.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>

Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.

It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.

Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).

The patch is based on the work by Maxim Artamonov.
Signed-off-by: NMaxim Artamonov <scn1874@yandex.ru>
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>

Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>

the lowlevel init sequence is the same so unify it
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The PM9261 board is based on the AT91SAM9261-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

optimize a few the RAM init
Signed-off-by: NIlko Iliev <iliev@ronetix.at>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

move PSRAM init to pm9263.c
this will allow us after to make the nor lowlevel_init generic
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The way the ALL variable is used allows for config.mk's to add more
targets themselves without having to clutter up the top level Makefile.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not
CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Building the compression code in lib_generic/ with -O2 rather than -Os
gives a nice speed boost without too much code size increase.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The latest version of U-Boot got a bit fatter in the BSS section which
caused overflows in the RAM region, so increase the monitor size.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The SPI flash layer is much stricter about sector usage than the eeprom
layer we used to use, so update the env settings to better match the
sector alignment of the flashes we use.
Signed-off-by: NVivi Li <vivi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The debug tools that interface with the other side of the JTAG console
got much slower when generalizing things, so bump up the default timeout
value on the U-Boot side to cope.  Hopefully at some point we can improve
the debug tools to speed things back up.
Signed-off-by: NVivi Li <vivi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This script is similar to the netconsole script, but instead works with
the JTAG console device driver that exists on Blackfin parts.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.
Signed-off-by: NThomas Smits <ts.smits@gmail.com>
Signed-off-by: NRemy Bohmer <linux@bohmer.net>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>