Adds new board SMDKC100 that uses s5pc100 SoC
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NHeungJun, Kim <riverful.kim@samsung.com>

The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>

these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.
Signed-off-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NTom Rix <Tom.Rix@windriver.com>

CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR
flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII
mode.
Signed-off-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NTom Rix <Tom.Rix@windriver.com>

Users should use microblaze-generic platform.
This platform is longer not supported.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch adds support for the DevKit8000 board.
Signed-off-by: NFrederik Kriewitz <frederik@kriewitz.eu>

The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.
Signed-off-by: NHarald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by
Calao Systems <http://www.calao-systems.com>. Their components are very
similar to the AT91SAM9260EK board, so their configuration is based on
the configuration of this board. There are however some differences:
different clocks, no LCD, no ethernet. They also can use SPI EEPROM to
store the environment.
Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems
<http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC
running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard
battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND
flash, two USB host ports, and an USB device port. More informations can be
found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936>
Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>

This patch adds support for i.MX27-LITEKIT development board from
LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND
flash, FEC ethernet controller integrated into i.MX27.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Acked-by: NWolfgang Denk <wd@denx.de>

The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.

Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the DEKA Research and Development galaxy5200 board

The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.
Signed-off-by: NEric Millbrandt <emillbrandt@dekaresearch.com>

Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: NReinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: NStefan Roese <sr@denx.de>

The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards.  Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Board support for the Guntermann & Drunck DL-Vision.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

This is Marvell's 88F6281_A0 based reference design board

This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product

This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported
Reviewed-by: NRonen Shitrit <rshitrit@marvell.com>
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support

This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported

Note: to boot Kirkwood kernel with USB support,
	you should add "usb start" in the boot sequence
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>

Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NWolfgang Denk <wd@denx.de>

The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).
Signed-off-by: NStefano Babic <sbabic@denx.de>

This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Acked-by: NFabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The PM9261 board is based on the AT91SAM9261-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NHoan Hoang <hnhoan@i-syst.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>