- 06 4月, 2021 3 次提交
-
-
由 Neil Armstrong 提交于
The Amlogic G12A & compatible SoCs embeds a mux to either communicate with the external PHY or the internal 10/100 PHY. This adds support for this mux as a MDIO MUX device. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Reviewed-by: NRamon Fried <rfried.dev@gmail.com>
-
由 Neil Armstrong 提交于
Add support for DM_MDIO to connect to PHY and expose a MDIO device for the internal MDIO bus in order to dynamically connect to MDIO PHYs with DT with eventual MDIO muxes in between. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Reviewed-by: NRamon Fried <rfried.dev@gmail.com>
-
由 Neil Armstrong 提交于
Add support for MMIO register MDIO muxes based on the Linux mdio-mux-mmioreg driver. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Reviewed-by: NRamon Fried <rfried.dev@gmail.com>
-
- 05 4月, 2021 5 次提交
-
-
由 Tom Rini 提交于
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Fabio Estevam 提交于
Currently it is not possible to boot Linux from the SD card by default. Make the necessary adjustments to allow it. Reported-by: NPeter Bergin <peter@berginkonsult.se> Signed-off-by: NFabio Estevam <festevam@gmail.com> Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
由 Tom Rini 提交于
In newer docutils writers/latex2e/docutils.sty has a unicode character in the comments which can in turn cause Python 3.6 at least to fail. Pin to the previous docutils release for now. Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Heinrich Schuchardt 提交于
The usb command cannot be compiled with CONFIG_USB=n: ld.bfd: cmd/usb.c:660: undefined reference to `usb_stop' ld.bfd: cmd/usb.c:663: undefined reference to `usb_started' Reviewed-by: NMarek Vasut <marex@denx.de> Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
- 01 4月, 2021 2 次提交
-
-
由 Simon Glass 提交于
This bash code is currently showing up in the build unless 'make -s' is used. We don't normally show these sorts of things as they are confusing. Also this code was not shown before the recent refactoring of how these messages are displayed. Add an '@' to silence it. Suggested-by: NTom Rini <trini@konsulko.com> Signed-off-by: NSimon Glass <sjg@chromium.org> Reported-by: NBin Meng <bmeng.cn@gmail.com> Fixes: 13732528 ("Makefile: Add common code to report deprecation")
-
https://source.denx.de/u-boot/custodians/u-boot-efi由 Tom Rini 提交于
Pull request for efi-2021-04-rc6 Bug fix: Fix ConvertDeviceNodeToText() for Uart()
-
- 31 3月, 2021 7 次提交
-
-
由 Tom Rini 提交于
Merge tag 'xilinx-for-v2021.07' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2021.07 net: - Fix gem PCS support spi: - Small trivial fixes zynq: - Enable time/timer commands - Update bitmain platform - Several DT changes zynqmp: - Update clock driver - mini config alignments - Add/update psu_init for zcu208/zcu216/zc1275 - Several DT changes - Enable efi debug command (also for Versal)
-
由 Andy Shevchenko 提交于
When test suite tries to create a file for a new filesystem test case and fails, the clean up of the exception tries to unmount the image, that has not yet been mounted. When it happens, the fuse_mounted global variable is set to False and inconveniently the test case tries to use sudo, so without this change the admin of the machine gets an (annoying) email: Subject: *** SECURITY information for example.com *** example.com : Feb 5 19:43:47 : ... COMMAND=/bin/umount .../build-sandbox/persistent-data/mnt and second run of the test cases on uncleaned build folder will ask for sudo which is not what expected. Besides that there is a double unmount calls during successfully run test case. All of these due to over engineered Python try-except clause and people didn't get it properly at all. The rule of thumb is that don't use more keywords than try-except in the exception handling code. Nevertheless, here we adjust code to be less intrusive to the initial logic behind that complex and unclear constructions in the test case, although it adds a lot of lines of the code, i.e. splits one exception handler to three, so on each step we know what cleanup shall perform. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
https://source.denx.de/u-boot/custodians/u-boot-sunxi由 Tom Rini 提交于
- H616 fixes to keep it in sync with upstream TF-A
-
由 Andre Przywara 提交于
Trusted Firmware now adds the /reserved-memory subnode to the DT at runtime[1], putting in the right values. Drop our hard-coded version, as this might clash with the actual values (which have also changed), and rely on TF-A to add the node. [1] https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7770Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NSamuel Holland <samuel@sholland.org> Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Andre Przywara 提交于
Loading Trusted-Firmware's BL31 at 16KB into DRAM was originally a hack to allow sharing more code with the other SoCs (which use this offset in SRAM). However there is no longer a reason for that, as the problematic macros have been properly separated there. The latest (and hopefully final) TF-A code drop now changes the load address to the beginning of DRAM, which is also more easily protected by the Trustzone memory controller (code to be done). Adjust the load address of BL31 now, to avoid any issues with incompatible versions later on (the TF-A patches are about to be merged). Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NSamuel Holland <samuel@sholland.org>
-
由 Heinrich Schuchardt 提交于
Fix a typo in helloworld.efi. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Heinrich Schuchardt 提交于
In the devicepath node to text conversion for Uart nodes a break statement is missing. Indicated by Coverity Scan CID 330038 Fixes: 62df6e9c ("efi_loader: Uart device path") Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
- 30 3月, 2021 19 次提交
-
-
由 Tom Rini 提交于
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next First set of u-boot-atmel features for 2021.07 cycle: This small feature set includes the implementation of the slew rate for the PIO4 pin controller device, and a fix for arm926ejs-based microprocessors that avoids a crash.
-
由 Michal Simek 提交于
Enable EFI debug command to be able to setup various efi variables to avoid software like grub. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Board has NAND and SD interfaces which can be used for saving variables too. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Still legacy formats are used that's why enable them by default. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Enable nand and smcc via DT. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 T Karthik Reddy 提交于
Use __func__ instead for function name in debug. Use Linux style u32 instead of uint32_t. Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com> Acked-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There are several changes which happen in mainline kernel which should get also to U-Boot. Here is the list of patches from the kernel: - ARM: zynq: Fix leds subnode name for zc702/zybo-z7 - arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1 - arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111 - arm64: dts: zynqmp: Wire up the DisplayPort subsystem - arm64: dts: zynqmp: Add DisplayPort subsystem - arm64: dts: zynqmp: Add DPDMA node - arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106 - arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111 - arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106 - arm64: dts: zynqmp-zcu100-revC: correct interrupt flags - arm64: dts: xilinx: align GPIO hog names with dtschema - arm64: zynqmp: Add Xilinx AES node - dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA but also some other changes have been done. - Using only one compatible string for adxl345 on zturn - Remove Xilinx internal DP bindings - Remove USB3.0 serdes configurations - Remove SATA serdes configuration for zc1232 - Resort nvmem_firmware - Update nand compatible string - Aling power-domains property for sd0/1 Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 T Karthik Reddy 提交于
With "clk dump" command, few clocks are showing up incorrect values and some clocks are displayed as "unknown". Add missing clocks to zynqmp clock driver to display proper clocks rates. Implement a simple way to get clock source, instead of calling functions. Change existing functions to this simple mechanism. Fix gem clock name "gem_rx" to "gem_tx" which was incorrect. Change dbf_fpd & dbf_lpd clk names to dbg_fpd & dbg_lpd. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com>
-
由 Amit Kumar Mahapatra 提交于
In zynqmp.dtsi file renamed "clk_sys" clock to "controller" and "clk_flash" clock to "bus" as per upstreamed Arasan NAND driver. This fixes NAND driver probe failure. Signed-off-by: NAmit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Amit Kumar Mahapatra 提交于
Update the following device tree properties for nand flash - Set software ecc mode. - Set bch as ecc algo. - Set read block to 0. Signed-off-by: NAmit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Update clock/pll setup, ddr, MIOs based on 2020.2 hw design. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is Linux driver for these chips that's why add it to device tree. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Add missing configurations file for zcu208 and zcu216. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ashok Reddy Soma 提交于
EMMC will have bus-width 8 and it is non-removable in general. These are missing from dt node. Add bus-width and non-removable parameters to emmc node. Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ashok Reddy Soma 提交于
size of malloc() pool for use before relocation is not sufficient for ZynqMP mini u-boot with emmc configuration. Increase it to 4K. Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Ashok Reddy Soma 提交于
Enable time command to get the elapsed time and timer commands. Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Robert Hancock 提交于
The code was trying to disable PCS auto-negotiation when a fixed-link node is present and enable it otherwise. However, the PCS registers were being written before the PCSSEL bit was set in the network configuration register, and it appears that in this state, PCS register writes are ignored. The result is that the intended change only took effect on the second network operation that was performed, since at that time PCSSEL is already enabled. Fix the order of register writes so that PCS registers are only written to after the PCS is enabled. Fixes: 26e62cc9 ("net: gem: Disable PCS autonegotiation in case of fixed-link") Signed-off-by: NRobert Hancock <robert.hancock@calian.com> Reviewed-by: NRamon Fried <rfried.dev@gmail.com> Reviewed-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Tom Rini 提交于
Prepare v2021.04-rc5
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 29 3月, 2021 4 次提交
-
-
git://git.denx.de/u-boot-dm由 Tom Rini 提交于
binman support for expanding entries, connections misc fixes and improvements to sandbox, etc. x86 CBFS improvements x86 coreboot improvements
-
由 Tom Rini 提交于
-
由 Jessica Clarke 提交于
On Arm-based Macs, -no_pie is ignored and gives a linker warning. Moreover, the build falls over with: ld: Absolute addressing not allowed in arm64 code but used in '_image_type_ptr_aisimage' referencing '_image_type_aisimage' for dumpimage and mkimage, since we put data structs in text sections not data sections and so cannot have dynamic relocations. Instead, move the sections to __DATA and drop disabling PIE. Signed-off-by: NJessica Clarke <jrtc27@jrtc27.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Sean Anderson 提交于
We need this header for U_BOOT_CMD, which is always present even without EFI. Fixes: 82c468a0 ("dm: test: Update Makefile conditions") Signed-off-by: NSean Anderson <seanga2@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-