The clk uclass was converted to support a live device tree recently,
hence the global data pointer declarations are no longer needed.
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Fix a mis-indented function call in clk_fixed_rate.c
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NMario Six <mario.six@gdsys.cc>

checkpatch.pl complains that the clk_ops structures used in clk-uclass.c
ought to be const, so we mark them as const.
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Sync with Linux commit 30a7acd573899fd8b("Linux 4.15-rc6")
to use enum pin_config_param.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

get_maintainer.pl quotes names which it considers unsafe, i.e. anything
containing [^a-zA-Z0-9_ \-]. This confuses patman, it will duplicate
addresses which are also in Series-to/cc. Strip the quotes.
Signed-off-by: NStefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The function dev_read_addr calls ofnode_get_addr_index in the live tree
case, which does not apply bus translations to the address read from the
device tree. This results in illegal addresses on boards that rely on
bus translations being applied.

Fix this situation by applying bus translations in the live tree case as
well.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
Tested-by: NStephen Warren <swarren@nvidia.com>

%s/falback/fallback/g
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Now the u-boot spi image is greater than 0x90000, increase the same in
env during spi erase.
Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

A 2 line help entry for a new Kconfig entry is, at this time, sufficient
in some cases, so lets drop that warning for now.
Signed-off-by: NTom Rini <trini@konsulko.com>

The following config symbols are only defined once and never referenced
anywhere else:

CONFIG_CYRUS
CONFIG_IDS8313
CONFIG_MPC8308_P1M
CONFIG_MPC8308RDB
CONFIG_MPC8349EMDS
CONFIG_MPC8349ITXGP
CONFIG_SBC8349
CONFIG_SBC8548
CONFIG_SBC8641D
CONFIG_TQM834X
CONFIG_VE8313
CONFIG_XPEDITE5140
CONFIG_XPEDITE5200
CONFIG_XPEDITE550X

Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: NMario Six <mario.six@gdsys.cc>

Move system flags from defconfig to mach-stm32/Kconfig
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NVikas Manocha <vikas.manocha@st.com>

Now this driver is used across stm32f4, stm32f7 and stm32h7
SoCs family, give it a generic name.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NVikas Manocha <vikas.manocha@st.com>

The following config symbols are only defined once and never referenced
anywhere else:

CONFIG_AMCORE
CONFIG_ASTRO5373L
CONFIG_M52277EVB
CONFIG_M5253DEMO
CONFIG_M5253EVBE
CONFIG_M5275EVB
CONFIG_M54418TWR
CONFIG_STMARK2

Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>

Seems to be again one of those CONFIG_ symbols named after a board, with
nothing referencing it.
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>

Last users of the following macros (for n = 0..7) were removed in
commit 5b8e76c3 ("powerpc, 8xx: remove support for 8xx"):

CONFIG_SYS_PCMCIA_PBRn
CONFIG_SYS_PCMCIA_PORn
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>

The corresponding changes in the uboot-test-hooks repo are:

https://github.com/swarren/uboot-test-hooks/pull/15Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: NTom Rini <trini@konsulko.com>

For preparation of adding AArch64 test.py jobs.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: NTom Rini <trini@konsulko.com>

It's mostly obvious, except that QEMU is annoying and requires an
explicit '-cpu cortex-a57' (or some other 64-bit core) to actually run
in 64-bit mode.

While at it, remove the references to setting the ARCH environment
variable; that is not used in U-Boot.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: NTom Rini <trini@konsulko.com>

This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: NTom Rini <trini@konsulko.com>

The signing certificate name is always 15 chars long, but need not be
null terminated. One solution is then to use printf precision modifiers
to only print this many chars ("%.15s"), but tiny printf does not support
this, so lets just drop printing the cert name for now.
Signed-off-by: NAndrew F. Davis <afd@ti.com>

Fix the size calculation in the verify boot. The header size
should be subtracted from the image size, not be assigned to
the image size.

Fixes: 0830d72b ("arm: am33xx: security: adds auth support for encrypted images")
Signed-off-by: NMadan Srinivas <madans@ti.com>
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

CONFIG_OF_EMBED in particular is needed to allow the Raspberry Pi
firmware to pass the DTB to U-Boot and on to the kernel.
Signed-off-by: NDrew Moseley <drew.moseley@northern.tech>

This commit adds UBIFS_NAND to BOOT_TARGET_DEVICES. This will
allow the kernel zImage to be loaded from '/boot/zImage' in UBIFS
(ubi0:rootfs).

Additionally update the *_MMC devices to also load kernel image from
the MMC 0:2 EXT4 file system.

DISTRO_DEFAULTS Setup

=====================

[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:2 /boot/zImage and run mmcbootz
[fallback 2] Check MMC 0:2 /boot/uImage and run mmcboot
[fallback 3] Check NAND UBIFS /boot/zImage and run nandbootubifs
[fallback 4] Check NAND partitions and run nandboot

The following "extlinux.conf" can be used to load images in the
top-level of the MMC 0:1 FAT partition.

[MMC(0:1)/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-evm
label omap3-evm
	kernel /zImage
	fdt /omap3-evm.dtb
	append console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>

initr_mem() is already enclosed by
	#if defined(CONFIG_PRAM)
	#endif

So there is no need to check CONFIG_PRAM again inside the
function.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The command portion of the GPIO driver can only be used in full SPL so
re-work to guard the command related portions and mark it as static.

Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

The command portion of the GPIO driver can only be used in full SPL so
re-work to guard the command related portions and mark it as static.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Change help description to match the style of the other U-Boot commands
and get rid of the leading whitespace.
Signed-off-by: NKlaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>

The message "reading %s\n" may be interesting when
debugging but otherwise it is superfluous.

Only output the message when debugging.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The message
"** %s shorter than offset + len **\n"
may be interesting when debugging but it does not indicate an
error.

So we should not write it if we are not in debug mode.

Fixes: 7a3e70cf fs/fs.c: read up to EOF when len would read past EOF
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

There is an #ifdef and #endif with nothing in between.  This patch simply
removes this dead/useless code.
Signed-off-by: NAdam Ford <aford173@gmail.com>

This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 BeagleBoard(s).

This commit adds OMAP3 BeagleBoard devicetree files from
Linux v4.15-rc5. This includes standard OMAP34XX board revisions as
well as the 'xM' which is OMAP36XX.
Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>

Select dtb name for am574x-idk and dra76x evm with acd package.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Add initial dts support for am574x-idk
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable CMD_DDR3 on all am57xx based platforms.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>".
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)

Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NKrunal Bhargav <k-bhargav@ti.com>

Update prcm, voltages and pinmux support for am574x-idk.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>