This converts the following to Kconfig:
   CONFIG_SYS_MALLOC_LEN
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NSean Anderson <seanga2@gmail.com>
Reviewed-by: NRick Chen <rick@andestech.com>

This converts the following to Kconfig:
   CONFIG_SKIP_LOWLEVEL_INIT
   CONFIG_SKIP_LOWLEVEL_INIT_ONLY

In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: NTom Rini <trini@konsulko.com>

- Guard most of the options in drivers/ddr/fsl/Kconfig with
  SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
  to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_I2C_SET_DEFAULT_BUS_NUM
   CONFIG_I2C_DEFAULT_BUS_NUMBER
Signed-off-by: NTom Rini <trini@konsulko.com>

- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
  based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
  CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
  CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
  to Kconfig.  We move these symbols around a bit and add appropriate
  dependencies to them.  In some cases, we now add a correct default value
  as well.
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_ID_EEPROM
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

The following boards no longer need CONFIG_DM_PCI_COMPAT enabled, so
remove that.
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

LS1028A-QDS has CONFIG_SPI_FLASH_SST and CONFIG_SPI_FLASH_EON defines
present in header. Move these entries from header to defconfigs.
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

There is no Spansion flash on LS1028A-RDB/QDS boards.
Unset CONFIG_SPI_FLASH_SPANSION option for both the boards.
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

The switch driver for LS1028A Ethernet switch is now compiled in for
the NXP LS1028A reference design boards and for the Kontron SMARC-sAL28.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: NMichael Walle <michael@walle.cc>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable CMD_GPIO for board ls1028aqds
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable CONFIG_NVME and CONFIG_CMD_NVME for Layerscape
platforms
Signed-off-by: NWasim Khan <wasim.khan@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: NTom Rini <trini@konsulko.com>

There is no reason to enable MEMTEST from headers when was converted to
Kconfig already.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rename fsl-ls1028a-qds.dts to fsl-ls1028a-qds.dtsi so that
it can be used as common device tree for lpuart and duart.
Add lpuart device tree and duart device tree respectively
for qds which are used with duart and lpuart console.
Signed-off-by: NVabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: NYuantian Tang <andy.tang@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable GIC_V3_ITS config to initialize the GIC redistributor
tables.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NWasim Khan <wasim.khan@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable FSPI controller support. So, flash environment can now be used
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

LS1028A QDS boards have a MDIO MUX and they require the driver for it for
PHYs to work.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

setexpr command is used while running secure boot
(chain of trust with confidentiality) feature.

Enable CONFIG_CMD_SETEXPR to enable setexpr command.
Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS.  Move this code to misc_init_r.  This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

The SDHC clock divider value for LS1028A should be default 2,
not 1.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>

Enable 4-byte Fast Read command for Flexspi AHB mode
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>

Since at least some of the drivers relevant to LS1028A are now following
DM, it's useful to have dm command enabled by default.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>