Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.

Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NTom Rini <trini@ti.com>

AM437x Starter Kit has a qspi flash and gbit ethernet
support. By muxing those signals, we can use those
interfaces from u-boot.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

pass correct PHY Address when running on SK
so that we have working ethernet with this board
too.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

when porting u-boot to a new am43xx board, it
helps to know the name of the current unsupported
board so we don't have to hunt for design documents
to figure out what's written in the EEPROM.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This family is supported by the TPS65218 PMIC.  Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).
Signed-off-by: NTom Rini <trini@ti.com>

Signed-off-by: NTom Rini <trini@ti.com>

The ePOS EVM and EVM SK have QSPI as an option to boot.  Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices.  As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.

Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

Add Ethernet Boot support to SPL
Acked-by: NTom Rini <trini@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

Updating EMIF_PHY_CTRL and adding EMIF_READ_WRITE_EXECUTION_THRESHOLD
registers.
In EMIF_PHY_CTRL:
Updating [4:0]READ_LATENCY to 8, because at higher frequencies like
400MHz the read latency expected will be CL+3 as per tests from HW
folks.
Clearing [19]PHY_DIS_CALIB_RST bit as this is used onl for debug
purpose. With out this resume is not working(Still waiting for PHY team
to come back for better explanation).
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: NTom Rini <trini@ti.com>

Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Reviewed-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

This patch enables dynamically powering down the
IO receiver when not performing a read on DDR3 board.
This optimizes both active and standby power consumption.
This is derived from a patch that is done on AM335x[1]

[1] http://arago-project.org/git/projects/?p=u-boot-am33x.git;a=commit;h=6a9ee4bc72ece53fabf01825605fba3d71d5feb2Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50	300MHz
OPP100	600MHz
OPP120	720MHz
OPPTB	800MHz
OPPNT	1000MHz
According to the latest DM following is the OPP table dependencies:
	VDD_CORE 	VDD_MPU
	OPP50		OPP50
	OPP50 		OPP100
	OPP100		OPP50
	OPP100		OPP100
	OPP100		OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz

Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

CONFIG_ENV_VARS_UBOOT_CONFIG, CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and
CONFIG_BOARD_LATE_INIT is already set. Adding support to detect the
board. These variables are used by findfdt.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Add support for reading onboard EEPROM to enable
board detection.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Use ti_armv7_common.h config file to inclde the common
configs.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>

Add dpll and clock data for AM43xx
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Add board specific information for AM43xx.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>