- 29 3月, 2018 6 次提交
-
-
由 Jörg Krause 提交于
The i.MX6ULL has a WDOG3 located at start address 0x021E0000 in the AIPS-2 memory region [1]. [1] i.MX 6ULL Applications Processor Reference Manual, Rev. 1, 11/2017, Table 2-3. AIPS-2 memory map, p. 178 Signed-off-by: NJörg Krause <joerg.krause@embedded.rocks>
-
由 Jörg Krause 提交于
The i.MX6UL has a WDOG3 located at start address 0x021E0000 in the AIPS-2 memory region [1]. [1] i.MX 6UltraLite Applications Processor Reference Manual, Rev. 1, 04/2016, Table-2-3 AIPS-2 memory map, p. 166 Signed-off-by: NJörg Krause <joerg.krause@embedded.rocks>
-
由 Nandor Han 提交于
This fixes environment variable location to avoid overlapping with U-Boot itself. Also more space for environment variables has been reserved to prevent future issues. Signed-off-by: NNandor Han <nandor.han@ge.com> Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
-
由 Anatolij Gustschin 提交于
HW accelerated "hash sha256 ..." command doesn't work on i.MX6UL, we get "CAAM was not setup properly or it is faulty" error message. This is due to wrong CAAM base 0x02100000, on i.MX6UL the CAAM base address is 0x02140000. Fix it. Note: with this patch applied the "hash sha256" commant still has some issues on i.MX6UL ("Invalid KEY Command" or other errors). With data cache off the "hash sha256" command works as expected. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Sriram Dash 提交于
Existing driver supports upto 4 I2C controllers. But some of future NXPs SoCs like lx2160a has eight I2C controllers. Update MXC driver to support upto 8 I2C controllers Signed-off-by: NSriram Dash <sriram.dash@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Sriram Dash 提交于
NXP layerscape platforms like ls1088a, ls2088a uses MXC I2C Controller. -Remove dependency of MX6 for the same. Update related configs to use Kconfig file. -Add SYS_I2C_MXC_I2C1,_I2C2,_I2C3,_I2C4 in Kconfig -Add CONFIG_SYS_MXC_I2C1_SPEED,_I2C2_,_I2C3_,_I2C4_ in Kconfig -Add CONFIG_SYS_MXC_I2C1_SLAVE,_I2C2_,_I2C3_,_I2C4_ in Kconfig Signed-off-by: NSriram Dash <sriram.dash@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 11 3月, 2018 6 次提交
-
-
由 Breno Lima 提交于
The README.mxc_hab is outdated and need improvements, add the following modifications: - Reorganize document and remove duplicate content - Add CST download link - Update CST package name - Align command lines with CST v2.3.3 - Update U-Boot binary name - Remove CSF padding since is not documented in AN4581 Signed-off-by: NBreno Lima <breno.lima@nxp.com>
-
由 Breno Lima 提交于
Currently the High Assurance Boot procedure is documented in two places: - doc/README.imx6 - doc/README.mxc_hab It is better to consolidate all HAB related information into README.mxc_hab file, so move the content from README.imx6 to README.mxc_hab. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Bryan O'Donoghue 提交于
commit cd2d4600 ("arm: imx: hab: Add IVT header definitions") declares struct ivt_header as "__attribute__((packed))". commit ed286bc8 ("imx: hab: Check if CSF is valid before authenticating image") declares struct hab_hdr with __packed. This patch makes the __packed convention consistent. Signed-off-by: NBryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com> Cc: Breno Lima <breno.lima@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Bryan O'Donoghue 提交于
commit ed286bc8 ("imx: hab: Check if CSF is valid before authenticating image") makes use of "__packed" as a prefix to the "struct hab_hdr" declaration. With my compiler "gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)" we get: ./arch/arm/include/asm/mach-imx/hab.h:42:25: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘{’ token struct __packed hab_hdr { Fix this problem by including <linux/compiler.h> Signed-off-by: NBryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com> Cc: Breno Lima <breno.lima@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Jagan Teki 提交于
This patch fixes the wrongly included dtsi file which was breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS. Linux commit details for the same change as "ARM: dts: imx6dl: Include correct dtsi file for Engicam i.CoreM6 DualLite/Solo RQS" (sha1: c0c6bb2322964bd264b4ddedaa5776f40c709f0c) Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Jagan Teki 提交于
usdhc4 node need to update pinctrl, bus-width and non-removable properties, sync the same from Linux. Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
- 10 3月, 2018 9 次提交
-
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Stefan Theil 提交于
The system call used by mkimage to run dtc redirects stdout to a temporary file. This can cause problems on Windows (with a MinGW cross-compiled version). Using the "-o" dtc parameter avoids this problem. Signed-off-by: NStefan Theil <stefan.theil@mixed-mode.de> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Marek Behún 提交于
Other filesystem drivers don't do this. Signed-off-by: NMarek Behun <marek.behun@nic.cz>
-
由 Heinrich Schuchardt 提交于
NETWORK should be after NAND_FLASH. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Heinrich Schuchardt 提交于
kmerr: verify that malloc and calloc are followed by a check to verify that we are not out of memory. badzero: Compare pointer-typed values to NULL rather than 0 Both checks are copied from the Linux kernel archive. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Heinrich Schuchardt 提交于
The iterator of list_for_each() is never NULL. Identified with coccinelle. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Alexander Graf 提交于
After the UART was initialized, we may still have bogus data in the RX queue if it was enabled with incorrect pin muxing before. So let's flush the RX queue whenever we initialize baud rates. This fixes a regression with the dynamic pinmuxing code when enable_uart=1 is not set in config.txt on Raspberry Pis that use pl011 for serial. Fixes: caf2233b ("bcm283x: Add pinctrl driver") Reported-by: NGöran Lundberg <goran@lundberg.email> Reported-by: NPeter Robinson <pbrobinson@gmail.com> Signed-off-by: NAlexander Graf <agraf@suse.de> Tested-by: NPeter Robinson <pbrobinson@gmail.com> Tested-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Alexander Graf 提交于
After the UART was initialized, we may still have bogus data in the RX queue if it was enabled with incorrect pin muxing before. So let's flush the RX queue whenever we initialize baud rates. This fixes a regression with the dynamic pinmuxing code when enable_uart=1 is not set in config.txt. Fixes: caf2233b ("bcm283x: Add pinctrl driver") Reported-by: NGöran Lundberg <goran@lundberg.email> Reported-by: NPeter Robinson <pbrobinson@gmail.com> Signed-off-by: NAlexander Graf <agraf@suse.de> Tested-by: NPeter Robinson <pbrobinson@gmail.com> Tested-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
- 09 3月, 2018 7 次提交
-
-
由 Tuomas Tynkkynen 提交于
The following config symbols are only defined once and never referenced anywhere else: CONFIG_AT91SAM9263EK CONFIG_AT91SAM9RLEK CONFIG_BARIX_IPAM390 CONFIG_BOARD_H2200 CONFIG_EP9301 CONFIG_KZM_A9_GT CONFIG_PICOSAM CONFIG_PLATINUM_PICON CONFIG_PLATINUM_TITANIUM CONFIG_PM9261 CONFIG_PM9263 CONFIG_PM9G45 CONFIG_SIEMENS_DRACO CONFIG_SIEMENS_PXM2 CONFIG_SIEMENS_RUT CONFIG_SMDKC100 CONFIG_SMDKV310 CONFIG_STM32F4DISCOVERY Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
The following config symbols are only defined once and never referenced anywhere else: CONFIG_ARM926EJS CONFIG_CPUAT91 CONFIG_EXYNOS5800 CONFIG_SYS_CORTEX_R4 Most of them are config symbols named after the respective SoCs which seems to have been a standard practice at some point. Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
The following config symbols are only defined once and never referenced anywhere else: CONFIG_DBAU1X00 CONFIG_PB1X00 Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Mario Six 提交于
The @gdsys.cc addresses are supposed to be used for mailing lists. Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc equivalent. Also, Dirk's address was wrong in one place; fix that as well. Signed-off-by: NMario Six <six@gdsys.cc>
-
由 Tuomas Tynkkynen 提交于
CONFIG_SYS_CBSIZE determines the maximum length of the kernel command line, and the default value of 256 is too small for booting some Linux images in the wild. Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
由 Yasushi SHOJI 提交于
Without the volatile attribute, compilers are entitled to optimize out the same asm(). In the case of __udelay() in syscounter.c, it calls `get_ticks()` twice, one for the starting time and the second in the loop to check the current time. When compilers inline `get_ticks()` they see the same `mrrc` instructions and optimize out the second one. This leads to infinite loop since we don't get updated value from the system counter. Here is a portion of the disassembly of __udelay: 88: 428b cmp r3, r1 8a: f8ce 20a4 str.w r2, [lr, #164] ; 0xa4 8e: bf08 it eq 90: 4282 cmpeq r2, r0 92: f8ce 30a0 str.w r3, [lr, #160] ; 0xa0 96: d3f7 bcc.n 88 <__udelay+0x88> 98: e8bd 8cf0 ldmia.w sp!, {r4, r5, r6, r7, sl, fp, pc} Note that final jump / loop at 96 to 88, we don't have any `mrrc`. With a volatile attribute, the above changes to this: 8a: ec53 2f0e mrrc 15, 0, r2, r3, cr14 8e: 42ab cmp r3, r5 90: f8c1 20a4 str.w r2, [r1, #164] ; 0xa4 94: bf08 it eq 96: 42a2 cmpeq r2, r4 98: f8c1 30a0 str.w r3, [r1, #160] ; 0xa0 9c: d3f5 bcc.n 8a <__udelay+0x8a> 9e: e8bd 8cf0 ldmia.w sp!, {r4, r5, r6, r7, sl, fp, pc} a2: bf00 nop I'm advised[1] to put volatile on all asm(), so this commit also adds it to the asm() in timer_init(). [1]: https://lists.denx.de/pipermail/u-boot/2018-March/322062.htmlSigned-off-by: NYasushi SHOJI <yasushi.shoji@gmail.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
Sometimes imximage throws the following error: CFGS board/freescale/vf610twr/imximage.cfg.cfgtmp CFGS board/freescale/vf610twr/imximage.cfg.cfgtmp MKIMAGE u-boot-dtb.imx Error: No BOOT_FROM tag in board/freescale/vf610twr/imximage.cfg.cfgtmp arch/arm/mach-imx/Makefile:100: recipe for target 'u-boot-dtb.imx' failed Later on, when running mkimage for the u-boot.imx it will succeed in finding the IVT offset. Looks like some race condition happening during parallel build when processing mkimage for u-boot-dtb.imx and u-boot.imx. A proper fix still needs to be implemented, but as a workaround let's remove the error when the IVT offset is not found. It is useful to have such message, especially during bring-up phase, but the build error that it causes is severe, so better avoid the build error for now. The error checking can be re-implemented later when we have a proper fix. Reported-by: NBreno Lima <breno.lima@nxp.com> Reported-by: NThomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
- 06 3月, 2018 2 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
- 05 3月, 2018 10 次提交
-
-
由 Tom Rini 提交于
This was missing the 'S' line causing a warning from genboardscfg.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
This should clean up a warning about a missing phy-cells Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Heinrich Schuchardt 提交于
POWER should be after ONENAND Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Fabio Estevam 提交于
Keep spelling.txt in sync with the version from kernel 4.16-rc4. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Adam Ford 提交于
Due to evolution of the MMC driver and better support, let's remove unnecessary undefs. Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Adam Ford 提交于
With the migration to Kconfig, the I2C block no longer exists in here. Let's clean up the comment. Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Ed Bartosh 提交于
Enable DHCP support for this board. Signed-off-by: NEd Bartosh <ed.bartosh@linux.intel.com> Signed-off-by: NMarek Vasut <marex@denx.de> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Masahiro Yamada 提交于
Thomas reported U-Boot failed to build host tools if libfdt-devel package is installed because tools include libfdt headers from /usr/include/ instead of using internal ones. This commit moves the header code: include/libfdt.h -> include/linux/libfdt.h include/libfdt_env.h -> include/linux/libfdt_env.h and replaces include directives: #include <libfdt.h> -> #include <linux/libfdt.h> #include <libfdt_env.h> -> #include <linux/libfdt_env.h> Reported-by: NThomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Paul Kocialkowski 提交于
There are no headers for libfdt in lib/libfdt, as they are instead located in scripts/dtc/libfdt. Specifying lib/libfdt for headers inclusion in host tools results in using the system libfdt headers, which is not what we want. Change this to the proper path. Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
-
由 Heinrich Schuchardt 提交于
Add a comment indicating that the German key map assumes code page 437. Add support for character ² (square sign) in the German key map. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-