- 01 6月, 2015 1 次提交
-
-
由 Joe Hershberger 提交于
Another shell scripting command that has not been moved. Moved using tools/moveconfig.py using these settings: CMD_SETEXPR bool n y Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
-
- 25 9月, 2014 1 次提交
-
-
由 Masahiro Yamada 提交于
CONFIG_CMD_BOOTM is defined in config_cmd_defaults.h which is forcebly included from each board. So, the default value of "config CMD_BOOTM" should be "y". For some boards undefining it (bf506f-ezkit, controlcenterd_TRAILBLA, controlcenterd_TRAILBLAZER_DEVELOP, controlcenterd_TRAILBLAZER), "# CONFIG_CMD_BOOTM is not set" should be added to their defconfig. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
- 25 7月, 2014 1 次提交
-
-
由 Dirk Eibach 提交于
Add the generic board infrastructure to all gdsys boards. Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 08 7月, 2014 1 次提交
-
-
由 Dirk Eibach 提交于
The I2C bridge on DP501 supports EDID, MCCS and HDCP by default. Allow EDID only to avoid I2C address conflicts. Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
-
- 25 1月, 2014 1 次提交
-
-
由 Masahiro Yamada 提交于
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk because all target boards with mpc85xx cpu define it. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
- 26 11月, 2013 1 次提交
-
-
由 York Sun 提交于
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: NYork Sun <yorksun@freescale.com>
-
- 05 11月, 2013 2 次提交
-
-
由 Rob Herring 提交于
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
由 Rob Herring 提交于
The definitions for CONFIG_SYS_PROMPT are varied with little reason other than to display the board name. Over half the definitions are "==> ", so make this the default. The rest of the boards remain unchanged to avoid breaking any external scripts expecting a certain prompt. Signed-off-by: NRob Herring <rob.herring@calxeda.com> Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 23 7月, 2013 1 次提交
-
-
由 Heiko Schocher 提交于
- added to fsl_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
-
- 17 7月, 2013 1 次提交
-
-
由 Dirk Eibach 提交于
The gdsys ControlCenter Digital board is based on a Freescale P1022 QorIQ SOC. It boots from SPI-Flash but can be configured to boot from SD-card for factory programming and testing. On board peripherals include: - 2x GbE - Lattice ECP3 FPGA connected via PCIe - mSATA RAID1 - USB host - DisplayPort video output - Atmel TPM Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: NReinhard Pfau <reinhard.pfau@gdsys.cc> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-