The soc node of the mpc52xx needs to be loaded with the IPB bus frequency,
not the XLB frequency.

This patch depends on the previous patches for MPC52xx device tree support
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>

This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".
Signed-off-by: NStefan Roese <sr@denx.de>

In the bootvx command the load address was only read from the env
variable "loadaddr" and not optionally passed as paramter as described
in the help. This is fixed with this patch. The behaviour is now the
same as in the bootelf command.
Signed-off-by: NStefan Roese <sr@denx.de>

Fixed include/ppc440.c for UIC address Bug

Corrects bug affecting the addresses for the universal interrupt
controller UIC2 and UIC3 on the PPC440 Epx, GRx, and SPE chips.
Signed-off-by: NJeff Mann <mannj@embeddedplanet.com>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch adds the code and configuration necessary to boot with an
arch/powerpc Linux kernel.
Signed-off-by: NGrant Likely <grant.likely@gmail.com>
Acked-by: NJon Loeliger <jdl@freescale.com>

Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

Patch below corrects the setting of the zmiifer register, it was
overwritting the register rather than ORing the settings.
Signed-off-by: NNeil Wilson <NWilson@airspan.com>
Signed-off-by: NStefan Roese <sr@denx.de>

The current NAND Bootloader setup forces the environment
variables to be in line with the bootloader. This change
enables the configuration to be made in the board include
file instead so that it can be individually enabled.
Signed-off-by: NNick Spence <nick.spence@freescale.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Two fixes for the nand_wait() function in
drivers/nand/nand_base.c:

1. Use correct timeouts. The original timeouts in Linux
source are 400ms and 20ms not 40s and 20s

2. Return correct error value in case of timeout. 0 is
interpreted as OK.
Signed-off-by: NRui Sousa <rui.sousa@laposte.net>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch allows an arch/ppc kernel to be booted by just passing 1 or 2
arguments to bootm.  It removes the getenv("disable_of") test that used
to be used for this purpose.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NJon Loeliger <jdl@freescale.com>

Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

- fix off-by-one error in board/tqm5200/cam5200_flash.c error message
- simplify "udate" definitions

Fixed cpu/ppc4xx/start.S for 440EPx Errata: further corrects PPC440EPx
errata 1.12: 440_33 by moving patch up in code.
Signed-off-by: NJeff Mann <mannj@embeddedplanet.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

   * Adds support for AMD command set Top Boot flash geometry reversal
   * Adds support for reading JEDEC Manufacturer ID and Device ID
   * Adds support for displaying command set, manufacturer id and
     device ids (flinfo)
   * Makes flinfo output to be consistent when CFG_FLASH_EMPTY_INFO defined
   * Removes outdated change history (refer to git log instead)
Signed-off-by: NTolunay Orkun <listmember@orkun.us>
Signed-off-by: NStefan Roese <sr@denx.de>

group is enabled for USB earlier (in cpu_init_f() instead of
usb_lowlevel_init()).

at least on G2 cores.

This fixes get_ram_size() problems on MPC5200 Rev. B boards.

 - add watchdog support
 - enable GPIO_WKUP_7 pin for input
 - code cleanup