- 24 1月, 2020 1 次提交
-
-
由 Alex Marginean 提交于
Currently LS1028A board code uses arch_misc_init to set up the board mux on QDS. Move this code to misc_init_r. This is consistent with LS gen 2 and T series SoCs/boards. Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 23 1月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 16 1月, 2020 1 次提交
-
-
由 Yangbo Lu 提交于
The SDHC clock divider value for LS1028A should be default 2, not 1. Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
-
- 26 12月, 2019 1 次提交
-
-
由 Kuldeep Singh 提交于
Enable 4-byte Fast Read command for Flexspi AHB mode Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 05 12月, 2019 2 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Miquel Raynal 提交于
MTD must be enabled when there is a SPI NOR flash using the SPI_FLASH_MTD config entry. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>
-
- 29 11月, 2019 1 次提交
-
-
由 Alex Marginean 提交于
Since at least some of the drivers relevant to LS1028A are now following DM, it's useful to have dm command enabled by default. Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 27 11月, 2019 1 次提交
-
-
由 Alex Marginean 提交于
LS1028A QDS board supports multiple combinations of SerDes protocols and multiple add-on cards with Ethernet PHYs. Some of them require specific configuration in Linux DT, and the plan is to use DT overlays for them. Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 21 11月, 2019 1 次提交
-
-
由 Tom Rini 提交于
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
- 08 11月, 2019 2 次提交
-
-
由 Udit Agarwal 提交于
Rename CONFIG_SECURE_BOOT to CONFIG_NXP_ESBC to avoid conflict with UEFI secure boot. Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 22 8月, 2019 1 次提交
-
-
由 Chuanhua Han 提交于
Enable related configs on all ls1028aqds boards to support pcf2127 rtc DM function. Signed-off-by: NChuanhua Han <chuanhua.han@nxp.com> Reviewed-by: NAlex Marginean <alexm.osslist@gmail.com> Tested-by: NAlex Marginean <alexm.osslist@gmail.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 14 8月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 7月, 2019 1 次提交
-
-
由 Alex Marginean 提交于
Enables ethernet, MDIO, PHY drivers for LS1028A RDB and QDS. Signed-off-by: NAlex Marginean <alexm.osslist@gmail.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 23 6月, 2019 1 次提交
-
-
由 Yangbo Lu 提交于
Moved CONFIG_FSL_ESDHC from header files to defconfig files. Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com> Tested-by: NSteffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NLukasz Majewski <lukma@denx.de> Reviewed-by: NMartyn Welch <martyn.welch@collabora.com> Acked-by: NJason Liu <Jason.hui.liu@nxp.com>
-
- 19 6月, 2019 1 次提交
-
-
由 Yuantian Tang 提交于
Add secure boot defconfig for ls1028aqds and ls1028ardb boards. Signed-off-by: NYuantian Tang <andy.tang@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 22 5月, 2019 3 次提交
-
-
由 Qiang Zhao 提交于
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Yuantian Tang 提交于
LS1028AQDS Development System is a high-performance computing, evaluation, and development platform that supports LS1028A QorIQ Architecture processor. Signed-off-by: NSudhanshu Gupta <sudhanshu.gupta@nxp.com> Signed-off-by: NRai Harninder <harninder.rai@nxp.com> Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: NBhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Signed-off-by: NTang yuantian <andy.tang@nxp.com> Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Yuantian Tang 提交于
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation platform that supports the LS1028A family SoCs. This patch add basic support of the platform. Signed-off-by: NSudhanshu Gupta <sudhanshu.gupta@nxp.com> Signed-off-by: NRai Harninder <harninder.rai@nxp.com> Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: NBhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Signed-off-by: NTang Yuantian <andy.tang@nxp.com> Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 30 4月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 2月, 2019 1 次提交
-
-
由 Peng Ma 提交于
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls208xardb and ls208xaqds defconfigs that missing one of them or more. enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK Support sata for all ls208xa defconfigs Signed-off-by: NPeng Ma <peng.ma@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 19 1月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 1月, 2019 2 次提交
-
-
由 Rajesh Bhagat 提交于
update TFABOOT defconfig for SD boot on below NXP chasis2 and chasis3 platforms: ls1043a, ls1046a, ls1088a and ls2088a. Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Rajesh Bhagat 提交于
TFABOOT support includes: - ls2088aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT Signed-off-by: NPankit Garg <pankit.garg@nxp.com> Signed-off-by: NRuchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 07 12月, 2018 1 次提交
-
-
由 Peng Ma 提交于
Enable related configs to support sata DM feature. Signed-off-by: NPeng Ma <peng.ma@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org> [YS: moveconfig -s -d] Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 20 10月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 9月, 2018 1 次提交
-
-
由 Yinbo Zhu 提交于
This enables the folowing to Kconfig: CONFIG_BLK CONFIG_DM_MMC Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 04 9月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 8月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: NAdam Ford <aford173@gmail.com> Acked-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 17 8月, 2018 1 次提交
-
-
由 Tom Rini 提交于
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 7月, 2018 1 次提交
-
-
This patch moves CONFIG_MP to Kconfig Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 28 4月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: NAdam Ford <aford173@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 4月, 2018 1 次提交
-
-
由 Mario Six 提交于
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 11 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 11月, 2017 1 次提交
-
-
由 Tom Rini 提交于
We first introduce CONFIG_USE_BOOTCOMMAND, similar to CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex scheme around this usage, and these have been defered for the moment so that platform maintainers can work on a migration plan. Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NLukasz Majewski <lukma@denx.de>
-
- 11 10月, 2017 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
- 28 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 8月, 2017 2 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Sam Protsenko 提交于
Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 8月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-