Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

This patch fixes a problem introdiced with patch
bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by
initdram()].

The boards affected are:
- PCI405
- PPChameleonEVB
- quad100hd
- taihu
- zeus
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This patch prevents linker error on AT91RM9200 boards, if
CONFIG_CMD_I2_TREE is set.
It implements i2c_set_bus_speed and i2c_get_bus_speed as a dummy function.
Signed-off-by: NJens Scharsig <esw@bus-elektronik.de>

ARM DaVinci: Remove duplicate code in cpu/arm926ejs/davinci/dp83848.c
Signed-off-by: NHugo Villeneuve <hugo.villeneuve@lyrtech.com>

__ARM__ is given by arm_config.mk automatically.
Signed-off-by: NShinya Kuribayashi <skuribay@ruby.dti.ne.jp>

Signed-off-by: NClaudio Scordino <claudio@evidence.eu.com>

This patch changes get_timer() for i.MX to return the time since
'base' instead of the time since the counter was at zero.

Symptom seen is flash timeout errors when erasing or programming a
sector using the common cfi flash code.
Signed-off-by: NAndrew Dyer <adyer@righthandtech.com>

1) Change the i.MX serial driver to use the baud rate set in the
 u-boot environment

2) don't assume a 16MHz value for PERCLK1 in baud rate calculations

3) don't write a 1 to the RDR bit in the USR2 reg. (bit is not "write
 one to clear" like other status bits in the reg.)
Signed-off-by: NAndrew Dyer <adyer@righthandtech.com>

Code in cpu/arm920t/start.S will die with a compilation error if
CONFIG_STACKSIZE + CFG_MALLOC_LEN works out to an invalid constant for
the ARM sub instruction.  Change the code so that each is subtracted
independently to avoid the error.
Signed-off-by: NAndrew Dyer <adyer@righthandtech.com>

- Correct Invalid #define of MPUTIM_PTV_MASK for
   omap1510 & omap730 register definition

 MPUTIM_PTV_MASK is defined as
 #define MPUTIM_PTV_MASK		(0x7<<PTV_BIT)

 while it should have been
 #define MPUTIM_PTV_MASK		(0x7<<MPUTIM_PTV_BIT)

- Below Patch corrects the same
Signed-off-by: NGururaja Hebbar <gururajakr@sanyo.co.in>

Signed-off-by: NAdrian Filipi <adrian.filipi@eurotech.com>

Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>

The i.MX31 has three SPI buses and each bus has several chip selects
and the MC13783 chip can be connected to any of these. The current
RTC driver for MC13783 is hardcoded for CSPI2/SS2.

This patch makes make MC13783 SPI bus and chip select configurable
via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>

This patch adds the reset_timer() function (needed by nand_base.c) and
modifies the get_timer_masked() to work in the same way as the omap24xx
function.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>

Also set up the port pins for using I2C.
Signed-off-by: NHeiko Schocher <hs@denx.de>

When not using hush, the autoscr command now executes lines that are
only one character long. It also runs the last line of scripts even if
it does not end in a newline.
Signed-off-by: NPetri Lehtinen <petri.lehtinen@inoi.fi>

On AMCC Arches board DTT_I2C_DEV_CODE is different then canyonlands
and glacier.
Signed-off-by: NVictor Gallardo <vgallardo@amcc.com>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Fix printf format-string/arg mismatches under -DDEBUG.

These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx.  Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: NAndrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

The e500um says the timebase is volatile out of reset.  To ensure
TB sync works we need to make sure its zero.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

print load_end value not pointer
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

...as done in image.c
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NMarkus Heidelberg <markus.heidelberg@web.de>

Signed-off-by: NMarkus Heidelberg <markus.heidelberg@web.de>

Fix the problem that cannot work RTL8169 on sh7785lcr board.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>

Add MTD SPI Flash support for M25P16, M25P20, M25P32,
M25P40, M25P64, M25P80, M25P128.
Signed-off-by: NJason McMullan <mcmullan@netapp.com>
Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>

We must link with libgeneric now.
Signed-off-by: NWolfgang Denk <wd@denx.de>