- 20 2月, 2014 1 次提交
-
-
由 Masahiro Yamada 提交于
Unlike Linux Kernel, U-Boot historically had *.dts files under board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/. I think arch/$(ARCH)/dts dicretory is a better location to store both *.dts and *.dtsi files. For example, before this commit, board/xilinx/dts directory had both Microblaze dts (microblaze-generic.dts) and ARM dts (zynq-*.dts), which are totally unrelated. This commit moves *.dts to arch/$(ARCH)/dts/ directories, allowing us to describe nicely mutiple DTBs generation in the next commit. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
- 12 7月, 2013 1 次提交
-
-
由 Stephen Warren 提交于
Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 15 3月, 2013 2 次提交
-
-
由 Tom Warren 提交于
Linux dts files were used for those boards that didn't already have sdhci info populated. Tamonten has their own dtsi file with common sdhci nodes (sourced from Linux). Signed-off-by: NTom Warren <twarren@nvidia.com> Tested-by: NThierry Reding <thierry.reding@avionic-design.de> Reviewed-by: NStephen Warren <swarren@nvidia.com>
-
由 Tom Warren 提交于
dts Makefile has the arch & board include paths added to DTS_CPPFLAGS. This allows the use of '#include "xyz"' in the dts/dtsi file which helps the C preprocessor find common dtsi include files. Signed-off-by: NTom Warren <twarren@nvidia.com> Reviewed-by: NStephen Warren <swarren@nvidia.com>
-
- 18 1月, 2013 2 次提交
-
-
由 Allen Martin 提交于
Sort nodes in dts files according the the following rules: 1) Any nodes that already exist in any /include/d file, in the order they appear in the /include/d file. 2) Any nodes with a reg property, in order of their address. 3) Any nodes without a reg property, alphabetically by node name. Signed-off-by: NAllen Martin <amartin@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Allen Martin 提交于
These nodes are unused. Signed-off-by: NAllen Martin <amartin@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 30 10月, 2012 1 次提交
-
-
由 Stephen Warren 提交于
The ULPI port is routed onto pins on the mini PCI Express connector. A standard breakout board may be used to access the port. * Add required DT entries to configure the ULPI port. * Setup up the ULPI pinmux in the board code. * Enable multiple USB controller and ULPI support in the board config. Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 08 9月, 2012 1 次提交
-
-
由 Stephen Warren 提交于
Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 01 9月, 2012 1 次提交
-
-
由 Allen Martin 提交于
This is make naming consistent with the kernel and devicetree and in preparation of pulling out the common tegra20 code. Signed-off-by: NAllen Martin <amartin@nvidia.com> Acked-by: NStephen Warren <swarren@wwwdotorg.org> Tested-by: NThierry Reding <thierry.reding@avionic-design.de> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 07 7月, 2012 2 次提交
-
-
由 Stephen Warren 提交于
... to enable USB host support, which enables Ethernet support. Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Stephen Warren 提交于
Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-