LX2160ARDB is an evaluation board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: NWasim Khan <wasim.khan@nxp.com>
Signed-off-by: NYogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: NMeenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: NVabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: NSriram Dash <sriram.dash@nxp.com>
Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: NPankit Garg <pankit.garg@nxp.com>
Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: NPeng Ma <peng.ma@nxp.com>
Signed-off-by: NChuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
[PK: Sqaush patches from Yinbo Zhu, Peng Ma, Chuanhua Han
and re-arrange defconfig]
Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

device-tree paths should never be used that reference node addresses
making an assumption about leading zeros. They should not be there per
the device-tree specification however they have been there until Linux
4.15 when they were removed via kernel commit
8dccafaa281aa1d240a58bbcdff338aec114a021.

This fixes various issues which will occur when using Linux 4.15+
that are being fixed up on a per model per PCB revision basis such as:
 - enabling MMC UHS-I on board revisions that support it
 - enabling PWM based on hwconfig
 - fixing PCIe reset on GW552x
 - removing cpu external watchdog reset on boards that do not support it
 - populate PCI dt nodes based on PCI scan in order to fix GW16082
   interrupt mapping and inject MAC address for PCI based GbE
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

The GW5904/GW5909 have a SP33E multi-protocol serial transceiver which we
want to configure to RS232 by default (by de-asserting RS485_EN)
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

Signed-off-by: NTim Harvey <tharvey@gateworks.com>

The GW5909 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW5904 but with half the DRAM loaded
and an additional RS232 transceiver off UART2.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

The GW5908 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW530x but with 1GiB density DRAM
(64bit 512MiB).
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

The GW5907 is a small single board computer based on the i.MX6DL SoC
with the following peripheral set:
 - DDR3 memory (512MB default)
 - 1x GigE (i.MX6 FEC)
 - Gateworks System Controller
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

The GW5906 is a GW552x with mechanical and power supply connector
differences.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

Signed-off-by: NTim Harvey <tharvey@gateworks.com>

Signed-off-by: NTim Harvey <tharvey@gateworks.com>

Signed-off-by: NTim Harvey <tharvey@gateworks.com>

The GW5905 is single-board tablet computer based on the i.MX6 SoC with the
following peripheral set:
 - eMMC flash (boot device)
 - microSD expansion
 - LVDS display connector for off-board 3D+1C with PWM backlight
   and I2C based touch controller
 - MIPI camera connector supporting the TRULY CM8487-B500SA-E (OV5640)
 - ublox EMMY-W1 WiFi/Bluetooth/NFC module (SDIO/UART)
 - ublox ZOE-M8Q GPS
 - LSM9DS1 9-DOF IMU
 - 1x 1-lane miniPCIe socket with USB 2.0
 - Gateworks System Controller
 - Audio jack with TLV320AIC Audio Codec, Speaker AMP
   and TSA227E Headphone detect
 - MAX8607 3-mode LED camera flash
 - DECT ULE module
 - FUSB302 USB-C PD and ISL9238 Battery charger
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

Do not setup I2C3 in the SPL for Ventana as some devices on that bus
(aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until
they are put into reset. Removing the setup of I2C3 from the SPL allows
the board-specific GPIO to be configured to take care of putting codecs
in reset prior to U-Boot setting up I2C3.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

The only UART that is garunteed on Ventana boards is UART2 (serial-console).

Remove UART1 pinmux as that it is not consistent across all Ventana boards
and U-Boot doesn't need it.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>

Signed-off-by: NTim Harvey <tharvey@gateworks.com>

Rely on the phy-reset-gpios which is set in imx6qdl-sabresd dtsi
and get rid of the enet reset gpio handling from the board file.
Signed-off-by: NAbel Vesa <abel.vesa@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabresd board file.
Signed-off-by: NAbel Vesa <abel.vesa@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabreauto board file.
Signed-off-by: NAbel Vesa <abel.vesa@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

Add the DM_GPIO related config for mx6sabreauto.
Also add the gpio request calls.
Signed-off-by: NAbel Vesa <abel.vesa@nxp.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

Add the DM_GPIO related config for mx6sabresd.
Also add the gpio request calls.
Signed-off-by: NAbel Vesa <abel.vesa@nxp.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

This matches one of the following three boards (or fails):
 - imx6q-sabreauto
 - imx6qp-sabreauto
 - imx6dl-sabreauto
Signed-off-by: NAbel Vesa <abel.vesa@nxp.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>

This matches one of the following three boards (or fails):
 - imx6q-sabresd
 - imx6qp-sabresd
 - imx6dl-sabresd
Signed-off-by: NAbel Vesa <abel.vesa@nxp.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>

distro boot expects that fdtfile name is setup for alternative DTB.
Create this file based on the first platform compatible string.
This should ensure that one rootfs can store multiple DTBs for different
boards.
Reflect structure which is used in Linux kernel. It means dtbs are
strored in xilinx folder.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NAlexander Graf <agraf@suse.de>

Add Raspberry Pi Compute Module 3+ to list of models, the revision code
is 0x10 according to the list on raspberrypi.org.

v2: Use the same dtb name as CM3 as CM3+ is a drop in replacement
    for CM3.
Signed-off-by: NJonathan Gray <jsg@jsg.id.au>
Reviewed-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NMatthias Brugger <mbrugger@suse.com>

The Ethernet has been broken for some time.  This patch unifies
this board with a few others that use a similar approach to
enabling phy.  This fixes ar8031 Ethernet controller so it works.
Signed-off-by: NAdam Ford <aford173@gmail.com>

All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>

Move hardcoded IOU_SWITCH_DIVISOR0 to Kconfig to be able to set it up
for different platforms.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Simplify code indentation.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Update boot_targets based on bootmode to run corresponding
distroboot command first.
Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

It is much easier to point to eeprom which stores information like MAC
address directly via DT. eeprom which contains this information is
pointed by /chosen/xlnx,eeprom parameter.

For example:
        chosen {
                bootargs = "earlycon";
                stdout-path = "serial0:115200n8";
+               xlnx,eeprom = &eeprom;
        };
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy
which is only one Zynq board which is using this feature.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

MV_DDR_FREQ_SAR lets the DDR frequency be determined by hardware
strapping. This also has the side effect of running the DDR clock in
synchronous mode with the CPU core clock rather than from an independent
PLL. We've seen this improve reliability in operation across a number of
boards and temperature ranges.
Signed-off-by: NChris Packham <judge.packham@gmail.com>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

Now that these boards use driver model we can drop the old code. At
present s5p_mmc_init() is still used by goni and smdkv310 so cannot be
removed unless we remove those boards.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NMinkyu Kang <mk7.kang@samsung.com>

This function is not needed now since the audio codecs have been converted
to proper drivers. The codec-enable GPIO is handled there.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NMinkyu Kang <mk7.kang@samsung.com>

At present the model is shown twice, once in the generic code and once
in the exynos code. Drop the latter.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NMinkyu Kang <mk7.kang@samsung.com>

The name of the board is bcm968580xref,
so rename the config to bcm968580xref too.
Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>

This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.

This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>

The TPS62517 PMIC driver has been partially converted to DM, so the
legacy I2C access layer isn't needed anymore.
Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>

Change maintainers to Prabhakar Kushwaha for fsl-qoriq, mpc85xx
and mpc86xx.
Signed-off-by: NYork Sun <york.sun@nxp.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Acked-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this
move, the legacy interface board_video_init() is removed from the
theadorable board code (only user of this video driver). The support
via DT will be added in a separate patch.

This patch also enables DM_VIDEO for the theadorable board, as this is
needed to not break git bisect'ability.
Signed-off-by: NStefan Roese <sr@denx.de>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NAnatolij Gustschin <agust@denx.de>