- 23 7月, 2014 11 次提交
-
-
由 Heiko Schocher 提交于
enable the W#/Vpp signal to disable writing to the status register on ST MICRON flashes like the N25Q128 thorugh the new config option CONFIG_SYS_SPI_ST_ENABLE_WP_PIN Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
-
由 Heiko Schocher 提交于
add enable_spi_clk(), so board code can enable spi clocks. Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Heiko Schocher 提交于
add basic support for the pwm modul found on imx6. Pieces of this code are based on linux code from drivers/pwm/pwm-imx.c Commit "cd3de83f1476 Linux 3.16-rc4" Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NStefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
-
由 Heiko Schocher 提交于
add defines for pwm modul found on imx6. Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Heiko Schocher 提交于
add IOMUXC_GPR1_USB_OTG_ID_OFFSET and IOMUXC_GPR1_USB_OTG_ID_SEL_MASK define for the USB_OTG_ID_SEL bit. Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Marek Vasut 提交于
As a result of 0defddc8 , which did a consolidation of the prompt string, this ifdef became empty. Remove it. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
On mx6solox there is an additional 0x4000 offset for the GPR registers. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
There is no need to keep iomuxc_base_regs structure as it serves the exact same purpose of the iomuxc structure, which is to provide access to the GPR registers. The additional fields of iomuxc_base_regs are not used. Other advantage of 'iomuxc' is that it has a shorter name and the variable declarations can fit into a single line. So remove iomuxc_base_regs structure and use iomuxc instead. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
The PFD issue is not present on mx6solox, so skip it in this case. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Iain Paton 提交于
Enable CONFIG_SYS_GENERIC_BOARD to remove warning on boot. Signed-off-by: NIain Paton <ipaton0@gmail.com>
-
- 16 7月, 2014 1 次提交
-
-
git://git.denx.de/u-boot由 Stefano Babic 提交于
Signed-off-by: NStefano Babic <sbabic@denx.de> Conflicts: boards.cfg
-
- 15 7月, 2014 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
- 14 7月, 2014 4 次提交
-
-
由 Pavel Machek 提交于
Timer on cyclone5 actually counts down. It took me a while to figure out, as timer counting in wrong direction actually _can_ be used, it just appears to tick at extremely high frequency in u-boot. The bug was introduced in commit 23ab7ee0. Signed-off-by: NPavel Machek <pavel@denx.de> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Lokesh Vutla 提交于
Update the board_name env variable and accordingly populate the dtb file. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Masahiro Yamada 提交于
In the previous commit, all the board fields were filled. Now we can use "-" in the board field for a different meaning. Going forward, "-" stands for no board directory as in cpu, soc, vendor fields. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
The boards.cfg file has allowed to use "-" for the board (= 6th) field if the board name is the same as the 7th field. But I notice one problem. Because tools/reformat.py sorts the lines in the simple alphabetical order (= the order of character code), some entries for the same board are not lined up together. For example, "bf527-ezkit" and "bf527-ezkit-v2" share the same board. But they are located separately because "bf527-ezkit" fills the board field with "-" whereas "bf527-ezkit-v2" specifies it explicitely. The similar things can be seen: - between "trizepsive" and "polaris" - between "RRvision" and "RRvision_LCD" - between "korat" and "korat_perm" - between "lwmon5" and "lcd4_lwmon5" This commit was generated by the following command: awk '$6 == "-" { $6 = $7 } { print }' boards.cfg \ | tools/reformat.py -i -d '-' -s 8 > boards0.cfg; \ mv boards0.cfg boards.cfg Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
- 12 7月, 2014 1 次提交
-
-
- 10 7月, 2014 7 次提交
-
-
由 Fabio Estevam 提交于
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
mx6sx does not have sata nor ipu blocks, so do not handle such clocks. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Add the pin definitions for mx6sx. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
mx6solox is the newest member of the mx6 family. Some of the new features on this variants are: - Cortex M4 microcontroller (besides the CortexA9) - Dual Gigabit Ethernet Add the initial support for it. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Eric Nelson 提交于
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not set in the same way as DISP0_DAT00-23, causing much flicker in parallel RGB displays on Dual-Lite and Solo processors. These settings now match the i.MX6 Dual and Quad core versions. Note that this fixes a regression in commit b47abc36 and that this is the second time we've had a regression on these two pads (See commit e654ddf7). Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com> Acked-by: NOtavio Salvador <otavio@ossystems.com.br>
-
由 Felipe Balbi 提交于
Newer AM437x silicon requires us to explicitly power up the USB2 PHY. By implementing usb_phy_power() we can achieve that. Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
由 Felipe Balbi 提交于
some boards won't work if the PHY isn't explicitly powered up. Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
- 09 7月, 2014 11 次提交
-
-
由 Michal Simek 提交于
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Lokesh Vutla 提交于
Updating omap4_sdp/panda and omap5_uevm maintainer. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Acked-by: NR Sricharan <r.sricharan@ti.com>
-
-
由 Fabio Estevam 提交于
Commit 3d622b78 (mx6: soc: Introduce set_ldo_voltage()) introduces set_ldo_voltage() function that can be used to set the voltages of any of the three LDO regulators controlled by the PMU_REG_CORE register. Prior to this commit there was a single set_vddsoc() which only configured the VDDSOC regulator. Update the comments to align with the new set_ldo_voltage() implementation. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Andre Renaud 提交于
DIV_SELECT is used as Fout = Fin * div_select / 2.0, so we should do the shift after the multiply to avoid rounding errors Signed-off-by: NAndre Renaud <andre@bluewatersys.com>
-
由 Lothar Rubusch 提交于
Signed-off-by: NMarek Vasut <marex@denx.de> Signed-off-by: NLothar Rubusch <lothar@denx.de> Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Marek Vasut 提交于
Adjust the mtdparts settings to allow for alternative boot images and for using UBI. Signed-off-by: NMarek Vasut <marex@denx.de> Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Marek Vasut 提交于
- "env ask", "env grep" and "setexpr" are needed for commissioning - add support for ext4 file systems - adjust default environment to use ext4 commands - add write support for (V)FAT and EXT4 - add bitmap and splashscreen support - print timestamp information for images Signed-off-by: NMarek Vasut <marex@denx.de> Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Lothar Rubusch 提交于
Signed-off-by: NMarek Vasut <marex@denx.de> Signed-off-by: NLothar Rubusch <lothar@denx.de>
-
由 Marek Vasut 提交于
Adjust the mtdparts to also consider factory-programmed config block. Signed-off-by: NMarek Vasut <marex@denx.de>
-
由 Marek Vasut 提交于
- "env ask", "env grep" and "setexpr" are needed for commissioning - add support for ext4 file systems - adjust default environment to use ext4 commands - add write support for (V)FAT and EXT4 - add bitmap and splashscreen support - print timestamp information for images Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
- 08 7月, 2014 4 次提交
-
-
-
由 Tyler Baker 提交于
The following patch re-enables the dhcp functionality on omap3_beagle. It was removed with df4dbb5d when omap3_beagle was converted to use ti_omap3_common.h. I have tested beagleboard and beagleboard-xm with this patch and confirmed dhcp is working. Signed-off-by: NTyler Baker <tyler.baker@linaro.org>
-
由 Alexey Ignatov 提交于
Fixes a bug when objcopy doesn't put .dtb.init.rodata section to resulting u-boot.bin, so u-boot was unable to find embedded DTB.
-
由 Ian Campbell 提交于
Signed-off-by: NIan Campbell <ijc@hellion.org.uk> Acked-by: NHans de Goede <hdegoede@redhat.com>
-