- 08 6月, 2015 8 次提交
-
-
由 Bhuvanchandra DV 提交于
Add iomux definitions for DSPI second instance. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
-
由 Bhuvanchandra DV 提交于
Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
-
由 Bhuvanchandra DV 提交于
Acked-by: NStefan Agner <stefan@agner.ch> Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
-
由 Bhuvanchandra DV 提交于
Inorder to use the pins as GPIO, apart from setting the alt-function, pinmuxing need to be done, this patch adds pinmux entries of few GPIOs. Acked-by: NStefan Agner <stefan@agner.ch> Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
-
由 Bhuvanchandra DV 提交于
Add GPIO driver support to Freescale VF610 Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
-
由 Bhuvanchandra DV 提交于
Like SPI and I2C few GPIO controllers also have multiple chip instances. This patch adds the flag 'DM_UC_FLAG_SEQ_ALIAS' in gpio_uclass driver to control device sequence numbering. By defalut the dev->r_seq for gpio_uclass will alwalys returns -1, which leads the gpio driver probe failure when using the driver with device trees. Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
-
由 Fabio Estevam 提交于
Commit 81830581 ("imx6: centralise common boot options in mx6_common.h") broke boot on mx6sl and mx6sx by assuming that all mx6 SoCs use the same LOADADDR/SYS_TEXT_BASE range, which is not correct. DDR on mx6sx/mx6sl starts at 0x80000000. Adjust LOADADDR/SYS_TEXT_BASE to the proper values for mx6sx/mx6sl, so that these SoCs can boot again. Also, TQMA6 requires a custom CONFIG_SYS_TEXT_BASE value, so move its setting prior to the inclusion of mx6_common.h. Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
-
由 Fabio Estevam 提交于
There are two revisions of wandboard: version B1 and C1. Add the revision detection support, so that the correct dtb file can be automatically loaded. Based on the patch from Richard Hu <hakahu@gmail.com>. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Reviewed-by: NStefano Babic <sbabic@denx.de> Tested-By: NVagrant Cascadian <vagrant@aikidev.net>
-
- 01 6月, 2015 8 次提交
-
-
由 Markus Niebel 提交于
this removes a config entry and uses the default value defined in config_fallbacks.h. This implements the same behaviour as a patch series for other i.MX6 boards from Freescale Signed-off-by: NMarkus Niebel <Markus.Niebel@tq-group.com>
-
由 Markus Niebel 提交于
Signed-off-by: NMarkus Niebel <Markus.Niebel@tq-group.com>
-
由 Tim Harvey 提交于
This avoids an error message on NAND-less boards. Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-
由 Tim Harvey 提交于
If the EEPROM could not be read or is corrupt we always want to hang. Note that an error message will have been displayed by read_eeprom in this case. Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-
由 Tim Harvey 提交于
The fdt_file1 and fdt_file2 vars provide fallbacks for the fdt file loading script. There is no need to allow the user to override these as if they want to specify the fdt, they should do so in the first attempt which is the fdt_file var. Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-
由 Tim Harvey 提交于
We want to model env var to always reflect what was in the EEPROM. There is no point in allowing a user to override this. Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-
由 Tim Harvey 提交于
- Added iomux for CAN_STBY and RS484_TEN (GW52xx/GW53xx/GW54xx/GW551x) - Moved iomux of USBHUB_RST# out of board_ehci_hcd_init so that it is done regardless of USB being initialized in bootloader - Added usb_sel iomux/hwconfig for GW552x - Fixed mezzanine DIO for GW54xx - Fixed PANLEDR# for GW54xx - Fixed dio iomux/hwconfig for GW552x - Fixed dio iomux for GW551x - removed redundant #define Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-
由 Stefan Wahren 提交于
In case the DC-DC is already enabled mxs_enable_4p2_dcdc_input() returns without reenabling brown out detection. So fix this issue by moving the return before brown out deactivation. Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com> Reviewed-by: NMarek Vasut <marex@denx.de>
-
- 28 5月, 2015 7 次提交
-
-
由 Fabio Estevam 提交于
After the mx6 config consolidation, 'save' command is no longer recognized. Pass the full command name 'saveenv' instead. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Select the fuse command support. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
CONFIG_SUPPORT_EMMC_BOOT is important to enable the boot partition via 'mmc partconf 0 1 1 0' command, for example. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Warp uses eMMC connected to esdhc2 port, so fix CONFIG_SYS_FSL_ESDHC_ADDR to reflect that. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Adjust CONFIG_SYS_DFU_DATA_BUF_SIZE in order to avoid the following error when running the dfu command: => dfu 0 mmc 0 dfu_get_buf: Could not memalign 0x2000000 bytes Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Tim Harvey 提交于
If CONFIG_PCI_SCAN_SHOW enabled then lets print a message of no link was detected. Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-
由 Stefano Babic 提交于
This reverts commit a0117a5e. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
- 27 5月, 2015 1 次提交
-
-
由 Stefano Babic 提交于
max_freq in print_cpuinfo is used only with imx6. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
- 26 5月, 2015 16 次提交
-
-
-
-
由 Peter Robinson 提交于
Move CONFIG_CMD_CACHE to mx6_common and standardise the way it's defined. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Reviewed-by: Tom Rini <trini at konsulko.com>
-
由 Peter Robinson 提交于
Move all standard mx6 MMC configs to mx6_common. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Reviewed-by: Tom Rini <trini at konsulko.com>
-
由 Peter Robinson 提交于
Move all standard filesystem, partition and fdt options to mx6_common. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Peter Robinson 提交于
Move generic miscellaneous options that are standard across most, if not all, mx6 boards to central mx6_common define to ensure consistent features. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Peter Robinson 提交于
Define common LOADADDR and BOOTDELAY to ensure a consistent experience across mx6 boards Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Peter Robinson 提交于
Define CONFIG_MXC_GPIO and CONFIG_CMD_GPIO by default in mx6_common Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Peter Robinson 提交于
Define the standard ATAG consfigs in mx6_common. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Reviewed-by: Tom Rini <trini at konsulko.com>
-
由 Peter Robinson 提交于
All boards define CONFIG_MX6, CONFIG_DISPLAY_BOARDINFO, CONFIG_DISPLAY_CPUINFO and CONFIG_SYS_GENERIC_BOARD so define them in mx6_common Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Reviewed-by: Tom Rini <trini at konsulko.com>
-
由 Peter Robinson 提交于
The linux/sizes.h, asm/arch/imx-regs.h, asm/imx-common/gpio.h, config_cmd_default.h includes are used fairly universally across imx6 boards so include them in mx6_common.h by default. We define CONFIG_SYS_NO_FLASH before config_cmd_default.h so that we don't have to undef CONFIG_CMD_FLASH / CONFIG_CMD_IMLS everywhere. Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
-
由 Peter Robinson 提交于
Standardise mx6_common.h to the same as other mx6 boards Signed-off-by: NPeter Robinson <pbrobinson@gmail.com> Reviewed-by: Tom Rini <trini at konsulko.com>
-
由 Tim Harvey 提交于
91199f4a broke mmc based Falcon mode. The block_read function returns the number of blocks read thus the error check needs to look for a return of 0 blocks read. Cc: Paul Kocialkowski <contact@paulk.fr> Signed-off-by: NTim Harvey <tharvey@gateworks.com> Acked-by: NPaul Kocialkowski <contact@paulk.fr>
-
由 Tim Harvey 提交于
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-
由 Tim Harvey 提交于
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-
由 Tim Harvey 提交于
We will use the same env size and redundancy used for NAND env for MMC. Signed-off-by: NTim Harvey <tharvey@gateworks.com>
-