- 13 9月, 2017 2 次提交
-
-
由 Rob Clark 提交于
EFI_LOADER really wants UTF-16 strings (ie. %ls and L"string" are 16bit chars instead of 32bit chars). But rather than enabling -fshort-wchar conditionally if EFI_LOADER is enabled, it was deemed preferrable to globally switch. Signed-off-by: NRob Clark <robdclark@gmail.com> Acked-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
-
- 12 9月, 2017 36 次提交
-
-
由 Tom Rini 提交于
We now can no longer re-use the provided path and need to give the full PATH we want used now. Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
由 Patrice Chotard 提交于
This allows to scan the DT including all "clocks" node's sub-nodes in which fixed-clock are defined. All fixed-clock should be defined inside a clocks node which collect all external oscillators. Until now, all clocks sub-nodes can't be binded except if the "simple-bus" compatible string is added which is a hack. Update test.dts by moving clk_fixed node inside clocks. Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Patrice Chotard 提交于
Currently, all fixed-clock declared in "clocks" node in device tree can be binded by clk_fixed_rate.c driver only if each of them have the "simple-bus" compatible string. This constraint has been invoked here [1]. This patch offers a solution to avoid adding "simple-bus" compatible string to nodes that are not busses. [1] https://patchwork.ozlabs.org/patch/558837/Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Chris Packham 提交于
Add support for reading a list of bouncing addresses from a in-tree file (doc/bounces) and from the ~/.patman config file. These addresses are stripped from the Cc list. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
-
由 Simon Glass 提交于
Adjust this code so that it can work with Python 2 and 3. Fixes: d73fcb12 (moveconfig: Support building a simple config database) Reported-by: NChris Packham <judge.packham@gmail.com> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Add a convenience macro to iterate over subnodes of a node. Make use of this where appropriate in the code. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present we sometimes see warnings of the form: /tmp/tmpMA89kB:36: warning: overriding the value of CMD_SPL. Old value: "y", new value: "y". This is not very useful as it does not show whch defconfig file it relates to. Update the tool to show this. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
It is often useful to see which driver was actually selected for each device. Add a new 'Driver' column to provide this information. Sample output: Class Probed Driver Name ---------------------------------------- root [ + ] root_drive root_driver keyboard [ + ] i8042_kbd |-- keyboard serial [ + ] ns16550_se |-- serial rtc [ ] rtc_mc1468 |-- rtc timer [ + ] tsc_timer |-- tsc-timer syscon [ + ] ich6_pinct |-- pch_pinctrl pci [ + ] pci_x86 |-- pci northbridge [ + ] bd82x6x_no | |-- northbridge@0,0 video [ + ] bd82x6x_vi | |-- gma@2,0 vidconsole0 [ + ] vidconsole | | `-- gma@2,0.vidconsole0 ... Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Tested-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Simon Glass 提交于
We can use printf() to limit the string width. Adjust the code to do this instead of using strlcpy() which is a bit clumbsy. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Tested-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bin Meng 提交于
Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct number depending on which host we are going to build and run. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
It seems most of the time we are building and running sandbox on 64-bit host. But we do support 32-bit host as well. Introduce Kconfig option for this. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Jean-Jacques Hiblot 提交于
There is an overflow problem when taking the size instead of the number of blocks in blk_create_device(). This results in a wrong device size: the device apparent size is its real size modulo 4GB. Using the number of blocks instead of the device size fixes the problem and is more coherent with the internals of the block layer. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Wenyou Yang 提交于
This option is an SPL-variant of the I2C_EEPROM option to enable the driver for generic I2C-attached EEPROMs for SPL. Signed-off-by: NWenyou Yang <wenyou.yang@microchip.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Wenyou Yang 提交于
Add the code to set the ethernet mac address from eeprom by using the common code from the common folder. Signed-off-by: NWenyou Yang <wenyou.yang@microchip.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Wenyou Yang 提交于
Replace the code to set the ethernet mac address with the code from the common folder. Signed-off-by: NWenyou Yang <wenyou.yang@microchip.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Wenyou Yang 提交于
Create board/$(VENDOR)/common folder to accommodate the common code shared by other atmel boards, now put the code to set ethernet mac address from eeprom, which uses the i2c eeprom driver. Signed-off-by: NWenyou Yang <wenyou.yang@microchip.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Lokesh Vutla 提交于
Select dtb name for am57xx BeagleBoard-X15 revC Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Add support for selecting proper dtb for am57xx BeagleBoard X15 revC u-boot from FIT Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Steve Kipisz 提交于
AM571x supports DDR running at 666MHz. Right now it is clocked at 532MHz which is lower than what is supported. In order to have maximum performance on AM571-IDK, switch DDR to 666MHz. Signed-off-by: NSteve Kipisz <s-kipisz2@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Add support for selecting proper dtb for dra76x u-boot from FIT. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Separate out u-boot specific compatibles from dts files. This will help in syncing dts files in future. Also these will get deleted eventually once respective drivers are capable of handling Linux dts files. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Sync all dra7* specific dts files with the upstream kernel including changes queued for 4.14 https://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git/log/?h=omap-for-v4.14/dt-v3Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Select dtb name for dra76-evm. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
ldo4 is used to poweron mmc on dra76-evm. Enable it. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Adding pinmux and IODELAY data for dra76-evm. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NVignesh R <vigneshr@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
dra76-evm has the ddr parts connectedi running at 666MHz: EMIF1: MT41K512M16HA-125 AIT:A x 2 EMIF2: MT41K512M8RH-125-AAT:E x 4 Add support for configuring the above DDR parts. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Keerthy 提交于
dra76-evm uses lp8736 and tps65917 pmic for powering on various peripherals. Add data for these pmics and register for dra76-evm. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NKeerthy <j-keerthy@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
The dra76-evm is a board based on TI's DRA76 processor Add eeprom support Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Praneeth Bajjuri 提交于
dra76 family is a high-performance, infotainment application device, based on OMAP architecture on a 28-nm technology. This contains most of the subsystems, peripherals that are available on dra74, dra72 family. This SoC mainly features Subsystems: - 2 x Cortex-A15 with max speed of 1.8GHz - 2 X DSP - 2 X Cortex-M4 IPU - ISS - CAL - DSS - VPE - VIP Connectivity peripherals: - 1 USB3.0 and 3 USB2.0 subsystems - 1 x SATA - 2 x PCI Express Gen2 - 3-port Gigabit ethernet switch - 2 x CAN - MCAN Adding CPU detection support for the dra76 ES1.0 soc and update prcm, control module, dplls data. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NPraneeth Bajjuri <praneeth@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
LP87565 is present on dra76-evm. Select it for TARGET_DRA7XX_EVM. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
It is not necessary that ldo1 is used to power on mmc. So, add support for passing ldo registers for powering on mmc. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
It is not necessary all omap5+ based uses the same PMIC to poweron mmc. So add support for enabling mmc based on board. Reviewed-by: NTom Rini <trini@konsulko.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Jorge Ramirez-Ortiz 提交于
Replacing original author Mateusz Kulikowski <mateusz.kulikowski@gmail.com> as db410c maintainer Signed-off-by: NJorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
-
- 11 9月, 2017 2 次提交
-
-
由 York Sun 提交于
CCN-504 HPF registers were believed to be accessible only from EL3. However, recent tests proved otherwise. Remove checking for exception level to re-enable L3 cache flushing for all levels. Signed-off-by: NYork Sun <york.sun@nxp.com> Tested-by: NZhao Qiang <qiang.zhao@nxp.com>
-
由 Hou Zhiqiang 提交于
Enabled PCIe support and PCI command feature. Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-