Some (not all) of ARMv7 boards define CONFIG_ARMV7, which is useless.
Besides, it is never referenced.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

When an MPC5200 based board is used with SPL support, the main
U-Boot needs to clear the GD (global data) struct again.

Otherwise the generic board init code in board_init_f (when
CONFIG_SYS_GENERIC_BOARD is defined) will not initialize all
GD variables correctly. Resulting in a hangup on the a4m2k
board.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>

a3m071 and a4m2k share one config header. So adding the generic board defines
in this one file is enough to convert both boards.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>

The gdsys hrcon board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.

On board peripherals include:
- 1x GbE (optional)
- Lattice ECP3 FPGA connected via eLBC and PCIe
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: NStefan Roese <sr@denx.de>

Wolfgang Denk found this issue using cppcheck:
(error) Uninitialized variable: fpga_features
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: NStefan Roese <sr@denx.de>

Addressing was completely broken for cmd_fpgad.
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: NStefan Roese <sr@denx.de>

The device id makes u-boot think that this chip needs
cfi_reverse_geometry(), which is not the case.
Add it to jedec_flash, so it is handled properly.
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: NStefan Roese <sr@denx.de>

Tune dlvision configuration similar to other gdsys boards to reduce memory
footprint.
Signed-off-by: NDirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: NStefan Roese <sr@denx.de>

The UBI layer will disable much of its error reporting when it is
compiled into the linux kernel to avoid stopping boot.  We want this
error reporting in U-Boot since we don't initialize the UBI layer until
it is used and want the error reporting.

We force this by telling the UBI layer we are building as a module.
Signed-off-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>

ff94bc40 "mtd, ubi, ubifs: resync with Linux-3.14"
introduced the writebufsize field in struct mtd_info, which
is not initialized in the cfi_flash driver, which leads in
not working ubi on cfi flashes. Fix it
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reported-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: NStefan Roese <sr@denx.de>
Acked-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>

The code for this board supports following features:
  - Boot media support: NAND flash/SD card/SPI flash
  - Support LCD display (optional, disabled by default)
  - Support ethernet
  - Support USB mass storage
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

The code for this board supports following features:
  - Boot media support: NAND flash/SD card/SPI flash
  - Support LCD display
  - Support ethernet
  - Support USB mass storage
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

The User Register in GMAC IP is used to select interface type.
When with GE feature, it is used to select interface between
RGMII and GMII. If without GE feature, it is used to select
interface between MII and RMII.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

As in SAMA5D4 SoC, the gf table in ROM code can not be seen.
So, when we try to use PMECC, we need to build it when do
initialization.
Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it
is defined we will build gf table runtime.

The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin

this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

replaces the at91bootstrap code with SPL code.

make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin

this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

add support for using spl code on at91sam9260 and at91sam9g45
based boards.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
[adopt Bo's change in spl.c]
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

device ready pin is signalling that the device is ready on state 1
not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NScott Wood <scottwood@freescale.com>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

using this driver in SPL code with CONFIG_SPL_NAND_ECC
configured leads in an compileerror. Fix this.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

enable to boot only a raw u-boot.bin image from nand with the
CONFIG_SPL_NAND_RAW_ONLY define. This option saves space on
boards where spl space is low.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

- compile mpddrc ram init code also for AT91SAM9M10G45
  based boards.
- in CONFIG_SAMA5D3 case, look for the ATMEL_MPDDRC_CR_DECOD_INTERLEAVED
  in the cr configuration
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

use the configure value for computing the ba_off value
not the value from the cr register. This leaded in a
wrong ram configuration on the upcoming corvus spl board
support.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NBo Shen <voice.shen@atmel.com>
Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h
and define a default value. Delete this define in the board
config files, where it is possible (all boards use currently
the same value).
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

generate the boot.bin file for all atmel SoC (arm920, arm926, armv7)
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
[fix subject]
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

The clock source for master clock can be slow clock, main clock,
plla clock or upll clock. So, make the clock source selection
field in mckr can be configured.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

We need to make sure the main clock ready field in MCFR is set
after switch to main crystal oscillator.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: NBo Shen <voice.shen@atmel.com>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

When boot up without mac address setting, it will give the warning
message like: "Warning: failed to set MAC address", however when
execute network related command, it still execute them without any
warning information.

With this patch, it will exit directly with following information:
"gmac0: mac address is not valid"

It also solve the problem after bootup then set mac address and the
mac address won't set to net device issue.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Tested-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>