- 23 10月, 2015 40 次提交
-
-
由 Mugunthan V N 提交于
In some platforms like am437x, serial node is not populated with clock-frequency node. So in that case have a default clock-clock frequency. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Mugunthan V N 提交于
enable mmc driver model for am335x gp_evm as omap_hsmmc supports driver model Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Mugunthan V N 提交于
enable mmc driver model for am335x bbb as omap_hsmmc supports driver model Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Mugunthan V N 提交于
adopt omap_hsmmc driver to device driver model Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
-
由 Mugunthan V N 提交于
Since spl doesn't support DM currently, do not define DM_MMC for spl build. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Mugunthan V N 提交于
Existing driver gets the actual omap hammc base address + 0x100 bytes as the first 0x100 bytes is not used by the driver. But with DM conversion the base address from DT is different, to accommodate the offset adding res0[0x100] to struct hsmmc. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Mugunthan V N 提交于
Import various DT files for dra7-evm from Linux Kernel v4.2 Add config file for this board, enable DM and DM_GPIO Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Add config file for k2g Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NVitaly Andrianov <vitalya@ti.com>
-
由 Lokesh Vutla 提交于
Add basic DT support for k2g evm. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
GPIO1_9 controls SPI flash on k2g evm. So make GPIO1_9 as output pin, inorder to use SPI. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Roger Quadros 提交于
Add MMC support for k2g Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Tested-by: NMugunthan V N <mugunthanvnm@ti.com>
-
由 Vitaly Andrianov 提交于
Add Ethernet support for tftp support Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Mugunthan V N 提交于
remove unused code as the same is achieved when configuring sgmii and link status is verifed. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
In K2G, Ethernet doesn't support SGMII instead it support RGMII, adding support to the driver to connect to RGMII phy. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
Fix Linkram size. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Mugunthan V N 提交于
Phy mode is a board property and it can be different between multiple board and ports, so it should not be hardcoded in driver to one specific mode. So adding a field in eth_priv_t structure to pass phy mode to driver. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
update K2G nav rx queue number Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
Coreect base addresses for SPI, Queue Manager, Ethernet, GPIO, and MSMC segments. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
Add pin mux data for k2g-evm Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
Add api for configuring pin mux. Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
Add ddr3 related info Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
Add psc information for k2g Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Vitaly Andrianov 提交于
Add clock information for Galileo Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
-
由 Vitaly Andrianov 提交于
Add pll data for k2g Signed-off-by: NVitaly Andrianov <vitalya@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Add Kconfig support Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Adding CPU detection support for Keystone2 Galileo. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Now that OF_CONTROL is enabled on all keystone2 platforms, build the default images with DT. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Import k2e specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Import k2l specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Import k2hk specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Keystone dts files assumes that LPAE is enabled and top level root node uses 64bit addresses. This breaks the keystone boot with CONFIG_OF_CONTROL enabled. So do not use 64 bit addresse in U-Boot DT. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Import various generic dts files from Linux kernel so that all keystone2 platforms can be DT in U-boot. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
If CONFIG_SYS_MALLOC_F_LEN is enabled, the stack is moved down to the specified size to make the malloc function available before relocation. But on keystone platforms SYS_SPL_MALLOC is immediately preceding stack, which is causing an overlap with this config enabled. So leave a gap between malloc space and stack space. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
With CONFIG_DM_SERIAL is enabled NS16550_init() cannot be called directly. Driver probe should be taking care of this. So call this function only when DM_SERIAL is not enabled. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Tom Rini 提交于
Tested on J6Eco EVM. Signed-off-by: NTom Rini <trini@konsulko.com> Tested-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Tom Rini 提交于
Tested on J6Eco EVM Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Tested on Pandaboard Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Nishanth Menon 提交于
Use the sandbox environment for the basic tests. Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NNishanth Menon <nm@ti.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Nishanth Menon 提交于
Introduce dummy devices for sandbox remoteproc device and enable it by default Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NNishanth Menon <nm@ti.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Nishanth Menon 提交于
Introduce a dummy driver for sandbox that allows us to verify basic functionality. This is not meant to do anything functional - but is more or less meant as a framework plumbing debug helper. The sandbox remoteproc driver maintains absolutey no states and is a simple driver which just is filled with empty hooks. Idea being to give an approximate idea to implement own remoteproc driver using this as a template. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NNishanth Menon <nm@ti.com> Acked-by: NSimon Glass <sjg@chromium.org>
-