As per new naming convention for Samsung SoC's, all Cortex-A9 and Cortex-A15
based SoC's will be classified under the name Exynos. Cortex-A9 and Cortex-A15
based SoC's will be sub-classified as Exynos4 and Exynos5 respectively.

In order to better adapt and reuse code across various upcoming Samsung Exynos
based boards, all uses of s5pc210 prefix/suffix/directory-names are renamed in
this patch. s5pc210 is renamed as exynos4210 and S5PC210/s5pc210 suffix/prefix
are renamed as exynos4/EXYNOS4.
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

In board_init_f() the gd->bd pointer is not valid when dram_init() is called.
This only avoids dying because DRAM is at zero on Tegra2. The common ARM
routine sets up the banks in the same way anyway, so we can just remove this
code.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

This message is not required, since it is followed by an 'official' U-Boot
message.

U-Boot 2011.03-00048-gd7cb0d3 (May 11 2011 - 17:17:23)

TEGRA2
Board: NVIDIA Seaboard
dynamic ram_size = 1073741824
DRAM:  1 GiB

becomes:

TEGRA2
Board: NVIDIA Seaboard
DRAM:  1 GiB

This is a separate commit since it changes behavior.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

This was used by the AVP in early boot but is no longer used. Unless we
plan to enable it somehow it is not needed. In any case we should try
to use the ns16550 driver instead as it has the same code.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

CONFIG_ENABLE_CORTEXA9 and CONFIG_SKIP_RELOCATE_UBOOT are not needed,
so remove them.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Since we have cache support built in we can remove Tegra's existing cache
initialization code amd other related dead code.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Since low-level init is skipped, the instruction cache is never enabled on
Tegra2. This explicitly calls this initialization as soon as the A9 is
initialized.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Some SOCs have do not start up with their 'main' CPU. The first U-Boot
code may then be executed with a CPU which does not have a CP15, or not a
useful one.

Here we split the initialization of CP15 into a separate call, which can
be performed later if required.

Once the main CPU is running, you should call cpu_init_cp15() to perform
this init as early as possible.

Existing ARMv7 boards which define CONFIG_SKIP_LOWLEVEL_INIT should not
need to change, this CP15 init is still skipped in that case. The only
impact for these boards is that the cpu_init_cp15() will be available
even if it is never used on these boards.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

The Tegra2 boot path is more complicated than it needs to be. Since we want
to move to building most of U-Boot with ARMv7 and only a small part with
ARMv4T (for AVP) it should be as simple as possible.

This makes tegra2_start() into a simple function which either does AVP
init or A9 init depending on which core is running it. Both cores now
following the same init path, beginning at _start, and the special Tegra2
boot path code is no longer required.

Only two files need to be built for ARMv4T, and this is handled in the
Tegra2 CPU Makefile.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

We want to move away from a special Tegra2 start-up, and just use
arch_cpu_init() instead. However, if we run board_init_f() from boot
we need to build it for ARMv4T, since the Tegra's AVP start-up CPU
does not support ARMv7.

The effect of this is to do the AVP init earlier, and in
arch_cpu_init(), rather that board_early_init_f().
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

... rather than open-coding the register accesses.

However, gpio_request() typically stores the "label" parameter in a global
data structure. This causes problems when called from gpio_config_uart(),
since the code is running before relocation. To solve this, pass a NULL
string to gpio_request(), and modify gpio_request() not to touch the string
if it's NULL.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Tested-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Ventana is a board which is very similar to Seaboard. Support it by
re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals.

v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets.
v6: Make gpio_config_uart_seaboard() static.
v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so
    he asked me to add myself for this board.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.

Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.

Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.

v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
    Remove prototype of gpio_config_mmc() from board.h
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Tested-by: NSimon Glass <sjg@chromium.org>
Acked-by: NSimon Glass <sjg@chromium.org>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

For Seaboard, this is mostly a cut/paste of board_mmc_init() and
pin_mux_mmc() into seaboard.c; pin_mux_mmc() was modified to add some
missing pinmux_tristate_disable calls for the GPIOs.

For Harmony, those functions were modified to configure SDMMC2 (index 2)
instead of SDMMC3 (index 1), since that's what is present on the board.

However, harmony.c is still missing the required GPIO setup, so neither
port is likely to function correctly yet.  This will be fixed in the next
change.

v4: Include board.h to prototype tegra2_mmc_init().
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NSimon Glass <sjg@chromium.org>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

During the rebase of commit 00b7d6ec "USB: Squash checkpatch warnings
in usb_kbd.c" I missed a brace, resulting in a number of build errors.
Fix these.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix:
da8xx_gpio.c: In function 'gpio_toggle_value':
da8xx_gpio.c:208:23: warning: variable 'bank' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Build dbau1550_el only in LIST_au1xx0_el and LIST_mips_el.
Also remove obsolete lists for mips5kc.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Thomas Lange <thomas@corelatus.se>

Fix:
ep0.c: In function 'ep0_get_descriptor':
ep0.c:187:8: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: NRemy Bohmer <linux@bohmer.net>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>

Fix:
core.c: In function 'usbd_device_event_irq':
core.c:596:21: warning: variable 'state' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: NRemy Bohmer <linux@bohmer.net>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>

Fix:
musb_udc.c: In function 'musb_peri_softconnect':
musb_udc.c:166:14: warning: variable 'intrtx' set but not used
[-Wunused-but-set-variable]
musb_udc.c:166:6: warning: variable 'intrrx' set but not used
[-Wunused-but-set-variable]
musb_udc.c:165:5: warning: variable 'intrusb' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: NRemy Bohmer <linux@bohmer.net>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>

Fix:
ehci-mxc.c: In function 'ehci_hcd_init':
ehci-mxc.c:113:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Sorry if this is already fixed somewhere - I could not find it.

This fixes these warnings:

usb_ohci.c: In function 'submit_control_msg':
usb_ohci.c:1081: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules
usb_ohci.c:1081: note: initialized from here
usb_ohci.c:1084: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules
usb_ohci.c:1084: note: initialized from here
usb_ohci.c:1087: warning: dereferencing pointer 'data_buf.76' does break strict-aliasing rules
usb_ohci.c:1087: note: initialized from here
Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Rebased to current code.
Signed-off-by: NWolfgang Denk <wd@denx.de>

This fixes the build of the two sh boards shmin and r7780mp and qemu-mips
which currently fail to build due to dropped pre-CONFIG_NET_MULTI code.

This v2 patch minimizes the number of lines in the diff for easy review
and to eliminate any possible accidential changes resulting from moving
lines of code in the file. This also makes the register function very easy.

Any cleanups and improvements are intentionally deferred to follow-up patches
to keep this patch as simple and as easy to review as possible.

A new driver register function, ne2k_register() calls the existing
one-time setup part of the old init function and calls eth_register().

Changes to shmin, r7780mp and qemu-mips:
- Call the new ne2k_register() from board_eth_init() of the boards.

- Tested using qemu-mips board,
- Tested the two renesas / sh boards r7780mp and shmin to compile again,
  and should work.

checkpatch-clean when "--ignore VOLATILE" is added to .checkpatch.conf,
and no warnings introduced in none of the three boards using this driver.
Signed-off-by: NBernhard Kaindl <bernhard.kaindl@gmx.net>

Fix:
inca-ip_sw.c: In function 'inca_switch_init':
inca-ip_sw.c:210:6: warning: variable 'v' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix:
board.c: In function 'board_init_r':
board.c:262:8: warning: unused variable 's' [-Wunused-variable]

(raised for configurations without ethernet support like
vct_premium_small)
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

Fix all errors and all warnings except for "externs should be avoided"
which could require more extensive changes.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

* 'master' of git://git.denx.de/u-boot-nand-flash:
  nand_spl/nand_boot.c: Fix build warning
  drivers/mtd/nand/nand_spl_load.c: Fix GCC 4.6 warning
  drivers/mtd/nand/nand_spl_simple.c: Fix GCC 4.6 warnings

Fix:
vpd.c: In function 'vpd_is_valid':
vpd.c:168:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
vpd.c:169:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
vpd.c:178:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
vpd.c: In function 'vpd_get_data':
vpd.c:281:6: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
vpd.c:291:6: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
vpd.c:297:6: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
vpd.c:302:6: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: NWolfgang Denk <wd@denx.de>

Accept 2 warnings "externs should be avoided".
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix:
flash.c: In function 'flash_init':
flash.c:47:25: warning: variable 'base_b1' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>

No full cleanup was attempted.  Warnings about "Use of volatile is
usually wrong" were ignored.  One line > 80 char was intentionally
accepted.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix:
fpga.c: In function 'fpgaDownload':
fpga.c:68:29: warning: variable 'val' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NWolfgang Denk <wd@denx.de>

Just reformated the code.  No attempts were made to clean up warnings
about "Use of volatile is usually wrong" or "externs should be avoided".
Signed-off-by: NWolfgang Denk <wd@denx.de>

The "rmu" board has long been unmaintained, and is broken.
Remove it.
Signed-off-by: NWolfgang Denk <wd@denx.de>

The OXC board has long been unmaintained, and is broken.
Remove it.
Signed-off-by: NWolfgang Denk <wd@denx.de>

The BAB7xx boards are almost deceased.  They cause build warnings, an
it's not worth the effort to fix these.  Remove the dead body.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>

Fix:
nand_boot.c: In function 'nand_read_page':
nand_boot.c:150:6: warning: variable 'stat' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Standard Debian powerpc and powerpcspe systems only include hard-float
libgcc in their native compilers, which causes scary build warnings when
building U-Boot.

Debian and other PowerPC-supporting distributions used to provide libgcc
and other libraries in a "nof" (soft-float) form in the "multilib"
packages.  As they were completely unused by the distribution and
therefore tended to be very buggy it was decided to save some time on
the part of the maintainers and build-servers by removing them.

Admittedly, right now the linker warnings do not indicate any problems,
as the included routines do not use any floating point at all.

The concern is that if floating-point code were ever added it might
cause hard-float code to be unexpectedly included in U-Boot without
generating a hard error.  This would cause unexplained crashes or
indeterminate results at runtime.

The easiest way to resolve this is to borrow the routines that U-Boot
needs from the Linux kernel, which has the same issue.

Specifically, the routines are: _ashldi3(), _ashrdi3(), and _lshrdi3().
They were borrowed from arch/powerpc/kernel/misc_32.S as of v2.6.38-rc5,
commit 85e2efbb1db9a18d218006706d6e4fbeb0216213, and are GPLv2+.

The Makefile framework was copied from the U-Boot ARM port.
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Stefan Roese <sr@denx.de>

Fix:
nand_spl_load.c: In function 'nand_boot':
nand_spl_load.c:31:6: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: NHeiko Schocher <hs@denx.de>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>