- 07 2月, 2014 1 次提交
-
-
由 Piotr Wilczek 提交于
This patch enables to read cpu revision on Exynos CPU. Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 05 2月, 2014 4 次提交
-
-
由 Inha Song 提交于
This patch fix the u-boot shell problem on TRATS2 board. - If hold the key while booting is in progress, white spaces are written in u-boot shell. Set Automatically clears after resetting Rx FIFO. Signed-off-by: NInha Song <ideal.song@samsung.com> Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NLukasz Majewski <l.majewski@samsung.com> Tested-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Minkyu Kang 提交于
Because of the list of peripherals is not sequential, such a routine does not check for valid correctly. Error check will be done when call the exynos_pinmux_config function. Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Acked-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NRajeshwari Shinde <rajeshwari.s@samsung.com>
-
由 Minkyu Kang 提交于
The value of PERIPH_ID_COUNT was wrong, and unnecessary. Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Minkyu Kang 提交于
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Acked-by: NRajehswari Shinde <rajeshwari.s@samsung.com>
-
- 03 2月, 2014 14 次提交
-
-
由 Przemyslaw Marczak 提交于
This change allows updating environment stored on MMC by dfu or thor. New setting: - "params.bin mmc 0x38 0x8" File params.bin can be generated by: tools/mkenvimage. e.g. ./mkenvimage -s 4096 -o params.bin <env_text_file> Every new env variable in text file should start with a new line. Sample env text file: - board/samsung/common/dfu_sample_env.txt Requirements: - file name: "params.bin" - file size: 4096 Bytes - the same as CONFIG_ENV_SIZE. Other size will cause CRC miscalculation at boot. Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> CC: Piotr Wilczek <p.wilczek@samsung.com> CC: Lukasz Majewski <l.majewski@samsung.com> Acked-by: NLukasz Majewski <l.majewski@samsung.com> Acked-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Acked-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
This simple LCD menu allows run one of download mode on device without writing on console or for fast and easy upgrade. This feature check user keys combination at boot: - power key + volume up - download menu - power key + volume down - thor mode (without menu) New configs: - CONFIG_LCD_MENU - CONFIG_LCD_MENU_BOARD For proper effect this feature needs following definitions: Power key: - KEY_PWR_PMIC_NAME - (string) pmic which supports power key check Register address: - KEY_PWR_STATUS_REG - KEY_PWR_INTERRUPT_REG Register power key mask: - KEY_PWR_STATUS_MASK - KEY_PWR_INTERRUPT_MASK Gpio numbers: - KEY_PWR_INTERRUPT_MASK - KEY_VOL_DOWN_GPIO Functions needs to be called: - keys_init() - for set proper gpio direction - check_boot_mode() - menu - main function Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
16 bpp mode is required by LCD console mode. This change updates exynos board files. Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Now fimd BPP color mode depends on vl_bpp value in struct "panel_info". There is only 16BPP mode check, default mode is 24BPP. Other fimd modes are usually unneeded and also needs some fimd driver modifications and tests. Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Changes: - check image bpp instead of resolution when returns logo address - remove 32bpp logo - add 16bpp logo in two formats: bmp and gzipped bmp - init logo address with "0" for unsupported bpp mode - update boards configs with proper image size for gunzip - extend structure vidinfo by two fields: logo_x_offset and logo_y_offset. Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Tested-by: NHyungwon Hwang <human.hwang@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Changes: - le16_to_cpu() to get_unaligned_le16() - le32_to_cpu() to get_unaligned_le32() when access fields in struct bmp header. This changes avoids data abort exception caused by unaligned data access. Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Acked-by: NAnatolij Gustschin <agust@denx.de> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Changes: new file: - board/samsung/common/misc.c depends on: CONFIG_MISC_COMMON - move draw_logo() to misc.c configs: trats, trats2, universal: - enable CONFIG_MISC_COMMON, - enable CONFIG_MISC_INIT_R, - add misc_init_r() and call draw_logo() in it. Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Remove wrong and unused env variables Trats2 is not as GT-I8800. Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Acked-by: NJaehoon Chung <jh80.chung@samsung.com> Cc: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Old s5p gpio coding method was not clean and was not working properly for all parts and banks. New method is clean and easy to extend. Gpio coding mask: 0x000000ff - pin number 0x00ffff00 - bank offset 0xff000000 - part number Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Vivek Gautam 提交于
Previously as a part of moving the VBUS gpio support to device tree following patch removed this and added relevant support in driver: 4a271cb1 exynos: usb: Switch USB VBUS GPIOs to be device tree configured Recent changes for common board file migration for exynos platform added it again. So removing it now. Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Vivek Gautam 提交于
The gpio_*() apis require the exact gpio line number to deduce the gpio bank and the gpio pin addresses. So fix the gpio number for VBUS used for EHCI ports as well as XHCI ports on exynos5250 boards. Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 29 1月, 2014 1 次提交
-
-
由 Albert ARIBAUD 提交于
-
- 28 1月, 2014 1 次提交
-
-
由 Albert ARIBAUD 提交于
-
- 27 1月, 2014 2 次提交
-
-
由 Fabio Estevam 提交于
Run "tools/reformat.py -i -d '-' -s 8 <boards.cfg >boards0.cfg && mv boards0.cfg boards.cfg" in order to keep the entries sorted. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Alexey Brodkin 提交于
This is only required for "PIC" relocation and doesn't apply to modern "PIE" relocation which does data relocation as well as code. "init_sequence_r" is just an array that consists of compile-time adresses of init functions. Since this is basically an array of integers (pointers to "void" to be more precise) it won't be modified during relocation - it will be just copied to new location as it is. As a consequence on execution after relocation "initcall_run_list" will be jumping to pre-relocation addresses. As long as we don't overwrite pre-relocation memory area init calls are executed correctly. But still it is dangerous because after relocation we don't expect initially used memory to stay untouched. Cc: Tom Rini <trini@ti.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Doug Anderson <dianders@chromium.org> Cc: Thomas Langer <thomas.langer@lantiq.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
- 25 1月, 2014 17 次提交
-
-
由 Dan Murphy 提交于
Add the USB host boot support for the am43xx evm Add the macros to boot from a usb drive in uBoot Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Dan Murphy 提交于
Add SPL support to be able to detect a USB Mass Storage device connected to a USB host. Once a USB Mass storage device is detected the SPL will load the u-boot.img from a FAT partition to target address. Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Dan Murphy 提交于
Move the FAT functions to a common location for reuse. Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_MPC5xxx in board config headers (and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Delete some serial.h files, whole code in which is surrounded by #if 0 ... #endif Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NStefan Roese <sr@denx.de>
-
由 Masahiro Yamada 提交于
The function os_free() returns nothing. Its return type should be "void" rather than "void *". Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Before this commit, all arch/arm/cpu/${CPU}/config.mk except ARMv8 had the same option: $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) This commit moves it into arch/arm/config.mk. If the compiler does not support the option, it is ignored by $(call cc-option,...). So this commit gives no harm to ARMv8. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk because all target boards with mpc86xx cpu define it. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk because all target boards with mpc85xx cpu define it. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_MPC824X in board config headers because it is defined in arch/powerpc/cpu/mpc824x/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_5xx in a source file because it is defined in arch/powerpc/cpu/mpc5xx/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_MPC512X in board config headers because it is defined in arch/powerpc/cpu/mpc512x/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_8xx in source files because it is defined in arch/powerpc/cpu/mpc8xx/config.mk Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_MPC83xx in board config headers because it is defined in arch/powerpc/cpu/mpc83xx/config.mk. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
We do not have to define CONFIG_4xx in board config headers because it is defined in arch/powerpc/cpu/ppc4xx/config.mk. include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx". I believe it is a typo because "CONFIG_4x" is not used at all in other files. So, I also deleted "CONFIG_4x" in include/configs/JSE.h. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Commit e5c5301f refactored the build system not to make directories in board makefiles. But commit 8f380381 create directories again in board/avionic-design/tec-ng/Makefile. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Alban Bedel <alban.bedel@avionic-design.de>
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-